Subversion Repositories or1k_soc_on_altera_embedded_dev_kit

|
|       x_operr.sa 3.5 7/1/91
|
|       fpsp_operr --- FPSP handler for operand error exception
|
|       See 68040 User's Manual pp. 9-44f
|
| Note 1: For trap disabled 040 does the following:
| If the dest is a fp reg, then an extended precision non_signaling
| NAN is stored in the dest reg.  If the dest format is b, w, or l and
| the source op is a NAN, then garbage is stored as the result (actually
| the upper 32 bits of the mantissa are sent to the integer unit). If
| the dest format is integer (b, w, l) and the operr is caused by
| integer overflow, or the source op is inf, then the result stored is
| garbage.
| There are three cases in which operr is incorrectly signaled on the
| 040.  This occurs for move_out of format b, w, or l for the largest
| negative integer (-2^7 for b, -2^15 for w, -2^31 for l).
|
|         On opclass = 011 fmove.(b,w,l) that causes a conversion
|         overflow -> OPERR, the exponent in wbte (and fpte) is:
|               byte    56 - (62 - exp)
|               word    48 - (62 - exp)
|               long    32 - (62 - exp)
|
|                       where exp = (true exp) - 1
|
|  So, wbtemp and fptemp will contain the following on erroneously
|         signalled operr:
|                       fpts = 1
|                       fpte = $4000  (15 bit externally)
|               byte    fptm = $ffffffff ffffff80
|               word    fptm = $ffffffff ffff8000
|               long    fptm = $ffffffff 80000000
|
| Note 2: For trap enabled 040 does the following:
| If the inst is move_out, then same as Note 1.
| If the inst is not move_out, the dest is not modified.
| The exceptional operand is not defined for integer overflow
| during a move_out.
|

|               Copyright (C) Motorola, Inc. 1990
|                       All Rights Reserved
|
|       For details on the license for this file, please see the
|       file, README, in this same directory.

X_OPERR:        |idnt    2,1 | Motorola 040 Floating Point Software Package

        |section        8

#include "fpsp.h"

        |xref   mem_write
        |xref   real_operr
        |xref   real_inex
        |xref   get_fline
        |xref   fpsp_done
        |xref   reg_dest

        .global fpsp_operr
fpsp_operr:
|
        link            %a6,#-LOCAL_SIZE
        fsave           -(%a7)
        moveml          %d0-%d1/%a0-%a1,USER_DA(%a6)
        fmovemx %fp0-%fp3,USER_FP0(%a6)
        fmoveml %fpcr/%fpsr/%fpiar,USER_FPCR(%a6)

|
| Check if this is an opclass 3 instruction.
|  If so, fall through, else branch to operr_end
|
        btstb   #TFLAG,T_BYTE(%a6)
        beqs    operr_end

|
| If the destination size is B,W,or L, the operr must be
| handled here.
|
        movel   CMDREG1B(%a6),%d0
        bfextu  %d0{#3:#3},%d0  |0=long, 4=word, 6=byte
        cmpib   #0,%d0          |determine size; check long
        beq     operr_long
        cmpib   #4,%d0          |check word
        beq     operr_word
        cmpib   #6,%d0          |check byte
        beq     operr_byte

|
| The size is not B,W,or L, so the operr is handled by the
| kernel handler.  Set the operr bits and clean up, leaving
| only the integer exception frame on the stack, and the
| fpu in the original exceptional state.
|
operr_end:
        bsetb           #operr_bit,FPSR_EXCEPT(%a6)
        bsetb           #aiop_bit,FPSR_AEXCEPT(%a6)

        moveml          USER_DA(%a6),%d0-%d1/%a0-%a1
        fmovemx USER_FP0(%a6),%fp0-%fp3
        fmoveml USER_FPCR(%a6),%fpcr/%fpsr/%fpiar
        frestore        (%a7)+
        unlk            %a6
        bral            real_operr

operr_long:
        moveql  #4,%d1          |write size to d1
        moveb   STAG(%a6),%d0   |test stag for nan
        andib   #0xe0,%d0               |clr all but tag
        cmpib   #0x60,%d0               |check for nan
        beq     operr_nan
        cmpil   #0x80000000,FPTEMP_LO(%a6) |test if ls lword is special
        bnes    chklerr         |if not equal, check for incorrect operr
        bsr     check_upper     |check if exp and ms mant are special
        tstl    %d0
        bnes    chklerr         |if d0 is true, check for incorrect operr
        movel   #0x80000000,%d0 |store special case result
        bsr     operr_store
        bra     not_enabled     |clean and exit
|
|       CHECK FOR INCORRECTLY GENERATED OPERR EXCEPTION HERE
|
chklerr:
        movew   FPTEMP_EX(%a6),%d0
        andw    #0x7FFF,%d0     |ignore sign bit
        cmpw    #0x3FFE,%d0     |this is the only possible exponent value
        bnes    chklerr2
fixlong:
        movel   FPTEMP_LO(%a6),%d0
        bsr     operr_store
        bra     not_enabled
chklerr2:
        movew   FPTEMP_EX(%a6),%d0
        andw    #0x7FFF,%d0     |ignore sign bit
        cmpw    #0x4000,%d0
        bcc     store_max       |exponent out of range

        movel   FPTEMP_LO(%a6),%d0
        andl    #0x7FFF0000,%d0 |look for all 1's on bits 30-16
        cmpl    #0x7FFF0000,%d0
        beqs    fixlong

        tstl    FPTEMP_LO(%a6)
        bpls    chklepos
        cmpl    #0xFFFFFFFF,FPTEMP_HI(%a6)
        beqs    fixlong
        bra     store_max
chklepos:
        tstl    FPTEMP_HI(%a6)
        beqs    fixlong
        bra     store_max

operr_word:
        moveql  #2,%d1          |write size to d1
        moveb   STAG(%a6),%d0   |test stag for nan
        andib   #0xe0,%d0               |clr all but tag
        cmpib   #0x60,%d0               |check for nan
        beq     operr_nan
        cmpil   #0xffff8000,FPTEMP_LO(%a6) |test if ls lword is special
        bnes    chkwerr         |if not equal, check for incorrect operr
        bsr     check_upper     |check if exp and ms mant are special
        tstl    %d0
        bnes    chkwerr         |if d0 is true, check for incorrect operr
        movel   #0x80000000,%d0 |store special case result
        bsr     operr_store
        bra     not_enabled     |clean and exit
|
|       CHECK FOR INCORRECTLY GENERATED OPERR EXCEPTION HERE
|
chkwerr:
        movew   FPTEMP_EX(%a6),%d0
        andw    #0x7FFF,%d0     |ignore sign bit
        cmpw    #0x3FFE,%d0     |this is the only possible exponent value
        bnes    store_max
        movel   FPTEMP_LO(%a6),%d0
        swap    %d0
        bsr     operr_store
        bra     not_enabled

operr_byte:
        moveql  #1,%d1          |write size to d1
        moveb   STAG(%a6),%d0   |test stag for nan
        andib   #0xe0,%d0               |clr all but tag
        cmpib   #0x60,%d0               |check for nan
        beqs    operr_nan
        cmpil   #0xffffff80,FPTEMP_LO(%a6) |test if ls lword is special
        bnes    chkberr         |if not equal, check for incorrect operr
        bsr     check_upper     |check if exp and ms mant are special
        tstl    %d0
        bnes    chkberr         |if d0 is true, check for incorrect operr
        movel   #0x80000000,%d0 |store special case result
        bsr     operr_store
        bra     not_enabled     |clean and exit
|
|       CHECK FOR INCORRECTLY GENERATED OPERR EXCEPTION HERE
|
chkberr:
        movew   FPTEMP_EX(%a6),%d0
        andw    #0x7FFF,%d0     |ignore sign bit
        cmpw    #0x3FFE,%d0     |this is the only possible exponent value
        bnes    store_max
        movel   FPTEMP_LO(%a6),%d0
        asll    #8,%d0
        swap    %d0
        bsr     operr_store
        bra     not_enabled

|
| This operr condition is not of the special case.  Set operr
| and aiop and write the portion of the nan to memory for the
| given size.
|
operr_nan:
        orl     #opaop_mask,USER_FPSR(%a6) |set operr & aiop

        movel   ETEMP_HI(%a6),%d0       |output will be from upper 32 bits
        bsr     operr_store
        bra     end_operr
|
| Store_max loads the max pos or negative for the size, sets
| the operr and aiop bits, and clears inex and ainex, incorrectly
| set by the 040.
|
store_max:
        orl     #opaop_mask,USER_FPSR(%a6) |set operr & aiop
        bclrb   #inex2_bit,FPSR_EXCEPT(%a6)
        bclrb   #ainex_bit,FPSR_AEXCEPT(%a6)
        fmovel  #0,%FPSR

        tstw    FPTEMP_EX(%a6)  |check sign
        blts    load_neg
        movel   #0x7fffffff,%d0
        bsr     operr_store
        bra     end_operr
load_neg:
        movel   #0x80000000,%d0
        bsr     operr_store
        bra     end_operr

|
| This routine stores the data in d0, for the given size in d1,
| to memory or data register as required.  A read of the fline
| is required to determine the destination.
|
operr_store:
        movel   %d0,L_SCR1(%a6) |move write data to L_SCR1
        movel   %d1,-(%a7)      |save register size
        bsrl    get_fline       |fline returned in d0
        movel   (%a7)+,%d1
        bftst   %d0{#26:#3}             |if mode is zero, dest is Dn
        bnes    dest_mem
|
| Destination is Dn.  Get register number from d0. Data is on
| the stack at (a7). D1 has size: 1=byte,2=word,4=long/single
|
        andil   #7,%d0          |isolate register number
        cmpil   #4,%d1
        beqs    op_long         |the most frequent case
        cmpil   #2,%d1
        bnes    op_con
        orl     #8,%d0
        bras    op_con
op_long:
        orl     #0x10,%d0
op_con:
        movel   %d0,%d1         |format size:reg for reg_dest
        bral    reg_dest        |call to reg_dest returns to caller
|                               ;of operr_store
|
| Destination is memory.  Get <ea> from integer exception frame
| and call mem_write.
|
dest_mem:
        leal    L_SCR1(%a6),%a0 |put ptr to write data in a0
        movel   EXC_EA(%a6),%a1 |put user destination address in a1
        movel   %d1,%d0         |put size in d0
        bsrl    mem_write
        rts
|
| Check the exponent for $c000 and the upper 32 bits of the
| mantissa for $ffffffff.  If both are true, return d0 clr
| and store the lower n bits of the least lword of FPTEMP
| to d0 for write out.  If not, it is a real operr, and set d0.
|
check_upper:
        cmpil   #0xffffffff,FPTEMP_HI(%a6) |check if first byte is all 1's
        bnes    true_operr      |if not all 1's then was true operr
        cmpiw   #0xc000,FPTEMP_EX(%a6) |check if incorrectly signalled
        beqs    not_true_operr  |branch if not true operr
        cmpiw   #0xbfff,FPTEMP_EX(%a6) |check if incorrectly signalled
        beqs    not_true_operr  |branch if not true operr
true_operr:
        movel   #1,%d0          |signal real operr
        rts
not_true_operr:
        clrl    %d0             |signal no real operr
        rts

|
| End_operr tests for operr enabled.  If not, it cleans up the stack
| and does an rte.  If enabled, it cleans up the stack and branches
| to the kernel operr handler with only the integer exception
| frame on the stack and the fpu in the original exceptional state
| with correct data written to the destination.
|
end_operr:
        btstb           #operr_bit,FPCR_ENABLE(%a6)
        beqs            not_enabled
enabled:
        moveml          USER_DA(%a6),%d0-%d1/%a0-%a1
        fmovemx USER_FP0(%a6),%fp0-%fp3
        fmoveml USER_FPCR(%a6),%fpcr/%fpsr/%fpiar
        frestore        (%a7)+
        unlk            %a6
        bral            real_operr

not_enabled:
|
| It is possible to have either inex2 or inex1 exceptions with the
| operr.  If the inex enable bit is set in the FPCR, and either
| inex2 or inex1 occurred, we must clean up and branch to the
| real inex handler.
|
ck_inex:
        moveb   FPCR_ENABLE(%a6),%d0
        andb    FPSR_EXCEPT(%a6),%d0
        andib   #0x3,%d0
        beq     operr_exit
|
| Inexact enabled and reported, and we must take an inexact exception.
|
take_inex:
        moveb           #INEX_VEC,EXC_VEC+1(%a6)
        movel           USER_FPSR(%a6),FPSR_SHADOW(%a6)
        orl             #sx_mask,E_BYTE(%a6)
        moveml          USER_DA(%a6),%d0-%d1/%a0-%a1
        fmovemx USER_FP0(%a6),%fp0-%fp3
        fmoveml USER_FPCR(%a6),%fpcr/%fpsr/%fpiar
        frestore        (%a7)+
        unlk            %a6
        bral            real_inex
|
| Since operr is only an E1 exception, there is no need to frestore
| any state back to the fpu.
|
operr_exit:
        moveml          USER_DA(%a6),%d0-%d1/%a0-%a1
        fmovemx USER_FP0(%a6),%fp0-%fp3
        fmoveml USER_FPCR(%a6),%fpcr/%fpsr/%fpiar
        unlk            %a6
        bral            fpsp_done

        |end