URL
https://opencores.org/ocsvn/pcie_ds_dma/pcie_ds_dma/trunk
Subversion Repositories pcie_ds_dma
[/] [pcie_ds_dma/] [trunk/] [core/] [ds_dma64/] [pcie_src/] [pcie_core64_m1/] [source/] [cmm_errman_cnt_en.v] - Rev 15
Go to most recent revision | Compare with Previous | Blame | View Log
//----------------------------------------------------------------------------- // // (c) Copyright 2009-2010 Xilinx, Inc. All rights reserved. // // This file contains confidential and proprietary information // of Xilinx, Inc. and is protected under U.S. and // international copyright and other intellectual property // laws. // // DISCLAIMER // This disclaimer is not a license and does not grant any // rights to the materials distributed herewith. Except as // otherwise provided in a valid license issued to you by // Xilinx, and to the maximum extent permitted by applicable // law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND // WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES // AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING // BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON- // INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and // (2) Xilinx shall not be liable (whether in contract or tort, // including negligence, or under any other theory of // liability) for any loss or damage of any kind or nature // related to, arising under or in connection with these // materials, including for any direct, or any indirect, // special, incidental, or consequential loss or damage // (including loss of data, profits, goodwill, or any type of // loss or damage suffered as a result of any action brought // by a third party) even if such damage or loss was // reasonably foreseeable or Xilinx had been advised of the // possibility of the same. // // CRITICAL APPLICATIONS // Xilinx products are not designed or intended to be fail- // safe, or for use in any application requiring fail-safe // performance, such as life-support or safety devices or // systems, Class III medical devices, nuclear facilities, // applications related to the deployment of airbags, or any // other applications that could lead to death, personal // injury, or severe property or environmental damage // (individually and collectively, "Critical // Applications"). Customer assumes the sole risk and // liability of any use of Xilinx products in Critical // Applications, subject only to applicable laws and // regulations governing limitations on product liability. // // THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS // PART OF THIS FILE AT ALL TIMES. // //----------------------------------------------------------------------------- // Project : V5-Block Plus for PCI Express // File : cmm_errman_cnt_en.v //-------------------------------------------------------------------------------- //-------------------------------------------------------------------------------- /*********************************************************************** Description: This is the error counter module for tracking the outstanding correctible/fatal. When overflow or underflow occurs, it remains at either full scale (overflow) or zero (underflow) instead of rolling over. ***********************************************************************/ `ifndef FFD `define FFD 1 `endif module cmm_errman_cnt_en ( count, // Outputs index, // Inputs inc_dec_b, enable, rst, clk ); output [3:0] count; input [2:0] index; // ftl_num, nfl_num or cor_num input inc_dec_b; // 1 = increment, 0 = decrement input enable; // err_*_en input rst; input clk; //******************************************************************// // Reality check. // //******************************************************************// parameter FFD = 1; // clock to out delay model //******************************************************************// // There are 2 pipeline stages to help timing. // // Stage 1: a simple add/subtract accumulator with no overflow or // // underflow check. // // Stage 2: underflow, overflow and counter enable are handled. // //******************************************************************// // Stage 1: count up or count down reg [3:0] reg_cnt; reg reg_extra; reg reg_inc_dec_b; reg reg_uflow; //wire [3:0] cnt; reg [3:0] cnt; wire oflow; wire uflow; always @(posedge clk or posedge rst) begin if (rst) {reg_extra, reg_cnt} <= #`FFD 5'b00000; else if (~enable) {reg_extra, reg_cnt} <= #`FFD 5'b00000; else if (inc_dec_b) {reg_extra, reg_cnt} <= #`FFD cnt + index; else {reg_extra, reg_cnt} <= #`FFD cnt - index; end //assign cnt = oflow ? 4'hF : (uflow ? 4'h0 : reg_cnt); always @(oflow or uflow or reg_cnt) begin case ({oflow,uflow}) // synthesis full_case parallel_case 2'b11: cnt = 4'hF; 2'b10: cnt = 4'hF; 2'b01: cnt = 4'h0; 2'b00: cnt = reg_cnt; endcase end always @(posedge clk or posedge rst) begin if (rst) reg_inc_dec_b <= #`FFD 1'b0; else reg_inc_dec_b <= #`FFD inc_dec_b; end assign oflow = reg_extra & reg_inc_dec_b; always @(posedge clk or posedge rst) begin if (rst) reg_uflow <= #`FFD 1'b0; else //reg_uflow <= #`FFD (count == 4'b0000) & (index[2:0] != 3'b000) & ~inc_dec_b; reg_uflow <= #`FFD ~|count & |index[2:0] & ~inc_dec_b; end assign uflow = reg_uflow; // Stage 2: if overflow occurs, the counter is set to full scale; // if underflow occurs, it is set to zero. // if counter is not enable, it is set to zero. reg [3:0] reg_count; always @(posedge clk or posedge rst) begin if (rst) reg_count <= #`FFD 4'b0000; else if (~enable) reg_count <= #`FFD 4'b0000; else if (oflow) reg_count <= #`FFD 4'b1111; else if (uflow) reg_count <= #`FFD 4'b0000; else reg_count <= #`FFD cnt; end assign count = reg_count; //******************************************************************// // // //******************************************************************// endmodule
Go to most recent revision | Compare with Previous | Blame | View Log