URL
https://opencores.org/ocsvn/pcie_ds_dma/pcie_ds_dma/trunk
Subversion Repositories pcie_ds_dma
[/] [pcie_ds_dma/] [trunk/] [core/] [ds_dma64/] [pcie_src/] [pcie_core64_m1/] [source_virtex6/] [axi_basic_tx_thrtl_ctl.vhd] - Rev 15
Go to most recent revision | Compare with Previous | Blame | View Log
------------------------------------------------------------------------------- -- -- (c) Copyright 2009-2011 Xilinx, Inc. All rights reserved. -- -- This file contains confidential and proprietary information -- of Xilinx, Inc. and is protected under U.S. and -- international copyright and other intellectual property -- laws. -- -- DISCLAIMER -- This disclaimer is not a license and does not grant any -- rights to the materials distributed herewith. Except as -- otherwise provided in a valid license issued to you by -- Xilinx, and to the maximum extent permitted by applicable -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON- -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and -- (2) Xilinx shall not be liable (whether in contract or tort, -- including negligence, or under any other theory of -- liability) for any loss or damage of any kind or nature -- related to, arising under or in connection with these -- materials, including for any direct, or any indirect, -- special, incidental, or consequential loss or damage -- (including loss of data, profits, goodwill, or any type of -- loss or damage suffered as a result of any action brought -- by a third party) even if such damage or loss was -- reasonably foreseeable or Xilinx had been advised of the -- possibility of the same. -- -- CRITICAL APPLICATIONS -- Xilinx products are not designed or intended to be fail- -- safe, or for use in any application requiring fail-safe -- performance, such as life-support or safety devices or -- systems, Class III medical devices, nuclear facilities, -- applications related to the deployment of airbags, or any -- other applications that could lead to death, personal -- injury, or severe property or environmental damage -- (individually and collectively, "Critical -- Applications"). Customer assumes the sole risk and -- liability of any use of Xilinx products in Critical -- Applications, subject only to applicable laws and -- regulations governing limitations on product liability. -- -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS -- PART OF THIS FILE AT ALL TIMES. -- ------------------------------------------------------------------------------- -- Project : Virtex-6 Integrated Block for PCI Express -- File : axi_basic_tx_thrtl_ctl.vhd -- Version : 2.3 -- -- Description: -- TX throttle controller. Anticipates back-pressure from PCIe block and -- preemptively back-pressures user design (packet boundary throttling). -- -- Notes: -- Optional notes section. -- -- Hierarchical: -- axi_basic_top -- axi_basic_tx -- axi_basic_tx_thrtl_ctl -------------------------------------------------------------------------------- -- Library Declarations -------------------------------------------------------------------------------- LIBRARY ieee; USE ieee.std_logic_1164.all; USE ieee.std_logic_unsigned.all; ENTITY axi_basic_tx_thrtl_ctl IS GENERIC ( C_DATA_WIDTH : INTEGER := 128; -- RX/TX interface data width C_FAMILY : STRING := "X7"; -- Targeted FPGA family C_ROOT_PORT : BOOLEAN := FALSE; -- PCIe block is in root port mode TCQ : INTEGER := 1 -- Clock to Q time ); PORT ( -- AXI TX ------------- S_AXIS_TX_TDATA : IN STD_LOGIC_VECTOR(C_DATA_WIDTH - 1 DOWNTO 0) := (OTHERS=>'0'); -- TX data from user S_AXIS_TX_TVALID : IN STD_LOGIC := '0'; -- TX data is valid S_AXIS_TX_TUSER : IN STD_LOGIC_VECTOR(3 DOWNTO 0) := "0000"; -- TX user signals S_AXIS_TX_TLAST : IN STD_LOGIC := '0'; -- TX data is last -- User Misc. ------------- USER_TURNOFF_OK : IN STD_LOGIC := '0'; -- Turnoff OK from user USER_TCFG_GNT : IN STD_LOGIC := '0'; -- Send cfg OK from user -- TRN TX ------------- TRN_TBUF_AV : IN STD_LOGIC_VECTOR(5 DOWNTO 0) := "000000"; -- TX buffers available TRN_TDST_RDY : IN STD_LOGIC := '0'; -- TX destination ready -- TRN Misc. ------------- TRN_TCFG_REQ : IN STD_LOGIC := '0'; -- TX config request TRN_TCFG_GNT : OUT STD_LOGIC ;--:= '0'; -- RX config grant TRN_LNK_UP : IN STD_LOGIC := '0'; -- PCIe link up -- 7 Series/Virtex6 PM ------------- CFG_PCIE_LINK_STATE : IN STD_LOGIC_VECTOR(2 DOWNTO 0) := "000"; -- Encoded PCIe link state -- Virtex6 PM ------------- CFG_PM_SEND_PME_TO : IN STD_LOGIC := '0'; -- PM send PME turnoff msg CFG_PMCSR_POWERSTATE : IN STD_LOGIC_VECTOR(1 DOWNTO 0) := "00"; -- PMCSR power state TRN_RDLLP_DATA : IN STD_LOGIC_VECTOR(31 DOWNTO 0) := x"00000000"; -- RX DLLP data TRN_RDLLP_SRC_RDY : IN STD_LOGIC := '0'; -- RX DLLP source ready -- Virtex6/Spartan6 PM ------------- CFG_TO_TURNOFF : IN STD_LOGIC := '0'; -- Turnoff request CFG_TURNOFF_OK : OUT STD_LOGIC ;--:= '0'; -- Turnoff grant -- System ------------- TREADY_THRTL : OUT STD_LOGIC ;--:= '0'; -- TREADY to pipeline USER_CLK : IN STD_LOGIC := '0'; -- user clock from block USER_RST : IN STD_LOGIC := '0' -- user reset from block ); END axi_basic_tx_thrtl_ctl; ARCHITECTURE trans OF axi_basic_tx_thrtl_ctl IS function tbuf_av_min_fn ( constant wdt : integer) return integer is variable buf_min : integer := 1; begin -- tbuf_av_min_fn if (wdt = 128) then buf_min := 5; elsif (wdt = 64) then buf_min := 1; else buf_min := 0; end if; return buf_min; end tbuf_av_min_fn; function tbuf_gap_time_fn ( constant wdt : integer) return integer is variable gap_time : integer := 1; begin -- tbuf_gap_time_fn if (wdt = 128) then gap_time := 4; else gap_time := 1; end if; return gap_time; end tbuf_gap_time_fn; -- Thrtl user when TBUF hits this val CONSTANT TBUF_AV_MIN : INTEGER := tbuf_av_min_fn(C_DATA_WIDTH); -- Pause user when TBUF hits this val CONSTANT TBUF_AV_GAP : INTEGER := TBUF_AV_MIN + 1; -- GAP pause time - the latency from the time a packet is accepted on the TRN -- interface to the time trn_tbuf_av from the Block will decrement. CONSTANT TBUF_GAP_TIME : INTEGER := tbuf_gap_time_fn(C_DATA_WIDTH); -- Latency time from when tcfg_gnt is asserted to when PCIe block will throttle CONSTANT TCFG_LATENCY_TIME : INTEGER := 2; CONSTANT LINKSTATE_L0 : INTEGER := 0; CONSTANT LINKSTATE_PPM_L1 : INTEGER := 1; CONSTANT LINKSTATE_PPM_L1_TRANS : INTEGER := 5; CONSTANT LINKSTATE_PPM_L23R_TRANS : INTEGER := 6; CONSTANT PM_ENTER_L1 : INTEGER := 32; CONSTANT POWERSTATE_D0 : INTEGER := 0; SIGNAL lnk_up_thrtl : STD_LOGIC; SIGNAL lnk_up_trig : STD_LOGIC; SIGNAL lnk_up_exit : STD_LOGIC; SIGNAL tbuf_av_min_thrtl : STD_LOGIC; SIGNAL tbuf_av_min_trig : STD_LOGIC; SIGNAL tbuf_av_gap_thrtl : STD_LOGIC; SIGNAL tbuf_gap_cnt : STD_LOGIC_VECTOR(2 DOWNTO 0); SIGNAL tbuf_gap_cnt_t : STD_LOGIC_VECTOR(2 DOWNTO 0); SIGNAL tbuf_av_gap_trig : STD_LOGIC; SIGNAL tbuf_av_gap_exit : STD_LOGIC; SIGNAL gap_trig_tlast : STD_LOGIC; SIGNAL gap_trig_tlast_1 : STD_LOGIC; SIGNAL gap_trig_decr : STD_LOGIC; SIGNAL gap_trig_decr_1 : STD_LOGIC; SIGNAL gap_trig_decr_2 : STD_LOGIC; SIGNAL tbuf_av_d : STD_LOGIC_VECTOR(5 DOWNTO 0); SIGNAL tcfg_req_thrtl : STD_LOGIC; SIGNAL tcfg_req_cnt : STD_LOGIC_VECTOR(1 DOWNTO 0); SIGNAL trn_tdst_rdy_d : STD_LOGIC; SIGNAL tcfg_req_trig : STD_LOGIC; SIGNAL tcfg_req_exit : STD_LOGIC; SIGNAL pre_throttle : STD_LOGIC; SIGNAL reg_throttle : STD_LOGIC; SIGNAL exit_crit : STD_LOGIC; SIGNAL reg_tcfg_gnt : STD_LOGIC; SIGNAL trn_tcfg_req_d : STD_LOGIC; SIGNAL tcfg_gnt_pending : STD_LOGIC; SIGNAL wire_to_turnoff : STD_LOGIC; SIGNAL reg_turnoff_ok : STD_LOGIC; SIGNAL tready_thrtl_mux : STD_LOGIC; SIGNAL ppm_L1_thrtl : STD_LOGIC; SIGNAL ppm_L1_trig : STD_LOGIC; SIGNAL ppm_L1_exit : STD_LOGIC; SIGNAL cfg_pcie_link_state_d : STD_LOGIC_VECTOR(2 DOWNTO 0); SIGNAL trn_rdllp_src_rdy_d : STD_LOGIC; SIGNAL ppm_L23_thrtl : STD_LOGIC; SIGNAL ppm_L23_trig : STD_LOGIC; SIGNAL cfg_turnoff_ok_pending : STD_LOGIC; SIGNAL reg_tlast : STD_LOGIC; SIGNAL cur_state : STD_LOGIC; SIGNAL next_state : STD_LOGIC; SIGNAL reg_axi_in_pkt : STD_LOGIC; SIGNAL axi_in_pkt : STD_LOGIC; SIGNAL axi_pkt_ending : STD_LOGIC; SIGNAL axi_throttled : STD_LOGIC; SIGNAL axi_thrtl_ok : STD_LOGIC; SIGNAL tx_ecrc_pause : STD_LOGIC; SIGNAL gap_trig_tcfg : STD_LOGIC; SIGNAL reg_to_turnoff : STD_LOGIC; SIGNAL reg_tx_ecrc_pkt : STD_LOGIC; SIGNAL tx_ecrc_pkt : STD_LOGIC; SIGNAL packet_fmt : STD_LOGIC_VECTOR(1 DOWNTO 0); SIGNAL packet_td : STD_LOGIC; SIGNAL header_len : STD_LOGIC_VECTOR(2 DOWNTO 0); SIGNAL payload_len : STD_LOGIC_VECTOR(9 DOWNTO 0); SIGNAL packet_len : STD_LOGIC_VECTOR(13 DOWNTO 0); SIGNAL pause_needed : STD_LOGIC; -- Declare intermediate signals for referenced outputs SIGNAL trn_tcfg_gnt_xhdl2 : STD_LOGIC; SIGNAL cfg_turnoff_ok_xhdl0 : STD_LOGIC; SIGNAL tready_thrtl_xhdl1 : STD_LOGIC; -- TYPE T_STATE is (IDLE_A,THROTTLE); -- SIGNAL CUR_STATE_A, NEXT_STATE_A : T_STATE; SIGNAL CUR_STATE_A, NEXT_STATE_A : STD_LOGIC; constant IDLE : std_logic := '0'; constant THROTTLE : std_logic := '1'; BEGIN -- Drive referenced outputs TRN_TCFG_GNT <= trn_tcfg_gnt_xhdl2; CFG_TURNOFF_OK <= cfg_turnoff_ok_xhdl0; TREADY_THRTL <= tready_thrtl_xhdl1; -------------------------------------------------------------------------------- -- THROTTLE REASON: PCIe link is down -- -- - When to throttle: trn_lnk_up deasserted -- -- - When to stop: trn_tdst_rdy assesrted -- -------------------------------------------------------------------------------- lnk_up_trig <= NOT(TRN_LNK_UP); lnk_up_exit <= TRN_TDST_RDY; PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN lnk_up_thrtl <= '1' AFTER (TCQ)*1 ps; ELSE IF (lnk_up_trig = '1') THEN lnk_up_thrtl <= '1' AFTER (TCQ)*1 ps; ELSIF (lnk_up_exit = '1') THEN lnk_up_thrtl <= '0' AFTER (TCQ)*1 ps; END IF; END IF; END IF; END PROCESS; -------------------------------------------------------------------------------- -- THROTTLE REASON: Transmit buffers depleted -- -- - When to throttle: trn_tbuf_av falls to 0 -- -- - When to stop: trn_tbuf_av rises above 0 again -- -------------------------------------------------------------------------------- tbuf_av_min_trig <= '1' WHEN (TRN_TBUF_AV <= TBUF_AV_MIN) ELSE '0'; PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN tbuf_av_min_thrtl <= '0' AFTER (TCQ)*1 ps; ELSE IF (tbuf_av_min_trig = '1') THEN tbuf_av_min_thrtl <= '1' AFTER (TCQ)*1 ps; -- The exit condition for tbuf_av_min_thrtl is !tbuf_av_min_trig ELSE tbuf_av_min_thrtl <= '0' AFTER (TCQ)*1 ps; END IF; END IF; END IF; END PROCESS; ------------------------------------------------------------------------------// -- THROTTLE REASON: Transmit buffers getting low // -- - When to throttle: trn_tbuf_av falls below "gap" threshold TBUF_AV_GAP // -- - When to stop: after TBUF_GAP_TIME cycles elapse // -- // -- If we're about to run out of transmit buffers, throttle the user for a // -- few clock cycles to give the PCIe block time to catch up. This is // -- needed to compensate for latency in decrementing trn_tbuf_av in the PCIe // -- Block transmit path. // ------------------------------------------------------------------------------// -- Detect two different scenarios for buffers getting low: -- 1) If we see a TLAST. a new packet has been inserted into the buffer, and -- we need to pause and let that packet "soak in" gap_trig_tlast_1 <= '1' WHEN (TRN_TBUF_AV <= TBUF_AV_GAP) ELSE '0'; gap_trig_tlast <= (gap_trig_tlast_1 AND S_AXIS_TX_TVALID AND tready_thrtl_xhdl1 AND S_AXIS_TX_TLAST ); -- 2) Any time tbug_avail decrements to the TBUF_AV_GAP threshold, we need to -- pause and make sure no other packets are about to soak in and cause the -- buffer availability to drop further. gap_trig_decr_1 <= '1' WHEN ( TRN_TBUF_AV = TBUF_AV_GAP) ELSE '0' ; gap_trig_decr_2 <= '1' WHEN (tbuf_av_d = TBUF_AV_GAP + 1) ELSE '0' ; gap_trig_decr <= ( gap_trig_decr_1 AND gap_trig_decr_2); gap_trig_tcfg <= ((tcfg_req_thrtl AND tcfg_req_exit)); tbuf_av_gap_trig <= (gap_trig_tlast OR gap_trig_decr OR gap_trig_tcfg) ; tbuf_av_gap_exit <= '1' WHEN (tbuf_gap_cnt = "000") ELSE '0' ; tbuf_gap_cnt_t <= "100" WHEN (C_DATA_WIDTH = 128) ELSE "001"; PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN tbuf_av_gap_thrtl <= '0' AFTER (TCQ)*1 ps; tbuf_gap_cnt <= "000" AFTER (TCQ)*1 ps; tbuf_av_d <= "000000" AFTER (TCQ)*1 ps; ELSE IF (tbuf_av_gap_trig = '1') THEN tbuf_av_gap_thrtl <= '1' AFTER (TCQ)*1 ps; ELSIF (tbuf_av_gap_exit = '1') THEN tbuf_av_gap_thrtl <= '0' AFTER (TCQ)*1 ps; END IF; -- tbuf gap counter: -- This logic controls the length of the throttle condition when tbufs are -- getting low. IF (tbuf_av_gap_thrtl = '1' AND (CUR_STATE_A = THROTTLE)) THEN IF (tbuf_gap_cnt > "000") THEN tbuf_gap_cnt <= tbuf_gap_cnt - "001" AFTER (TCQ)*1 ps; END IF; ELSE tbuf_gap_cnt <= tbuf_gap_cnt_t AFTER (TCQ)*1 ps; END IF; tbuf_av_d <= TRN_TBUF_AV AFTER (TCQ)*1 ps; END IF; END IF; END PROCESS; ------------------------------------------------------------------------------ -- THROTTLE REASON: Block needs to send a CFG response -- - When to throttle: trn_tcfg_req and user_tcfg_gnt asserted -- - When to stop: after trn_tdst_rdy transitions to unasserted -- -- If the block needs to send a response to a CFG packet, this will cause -- the subsequent deassertion of trn_tdst_rdy. When the user design permits, -- grant permission to the block to service request and throttle the user. ------------------------------------------------------------------------------ tcfg_req_trig <= (TRN_TCFG_REQ AND reg_tcfg_gnt); tcfg_req_exit <= '1' WHEN (tcfg_req_cnt = "00" AND trn_tdst_rdy_d = '0' AND TRN_TDST_RDY ='1') ELSE '0'; PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN tcfg_req_thrtl <= '0' AFTER (TCQ)*1 ps; trn_tcfg_req_d <= '0' AFTER (TCQ)*1 ps; trn_tdst_rdy_d <= '1' AFTER (TCQ)*1 ps; reg_tcfg_gnt <= '0' AFTER (TCQ)*1 ps; tcfg_req_cnt <= "00" AFTER (TCQ)*1 ps; tcfg_gnt_pending <= '0' AFTER (TCQ)*1 ps; ELSE IF (tcfg_req_trig = '1') THEN tcfg_req_thrtl <= '1' AFTER (TCQ)*1 ps; ELSIF (tcfg_req_exit = '1') THEN tcfg_req_thrtl <= '0' AFTER (TCQ)*1 ps; END IF; -- We need to wait the appropriate amount of time for the tcfg_gnt to -- "sink in" to the PCIe block. After that, we know that the PCIe block will -- not reassert trn_tdst_rdy until the CFG request has been serviced. If a -- new request is being service (trn_tcfg_gnt == 1), then reset the timer. IF ((NOT(trn_tcfg_req_d = '1' ) AND TRN_TCFG_REQ = '1' ) OR tcfg_gnt_pending = '1') THEN -- As TCFG_LATENCY_TIME value is 2 tcfg_req_cnt <= "10" AFTER (TCQ)*1 ps; ELSE IF (tcfg_req_cnt > "00") THEN tcfg_req_cnt <= tcfg_req_cnt - "01" AFTER (TCQ)*1 ps; END IF; END IF; -- Make sure trn_tcfg_gnt pulses once for one clock cycle for every -- cfg packet request. IF (TRN_TCFG_REQ = '1' AND NOT(trn_tcfg_req_d = '1' )) THEN tcfg_gnt_pending <= '1' AFTER (TCQ)*1 ps; ELSIF (trn_tcfg_gnt_xhdl2 = '1') THEN tcfg_gnt_pending <= '0' AFTER (TCQ)*1 ps; END IF; trn_tcfg_req_d <= TRN_TCFG_REQ AFTER (TCQ)*1 ps; trn_tdst_rdy_d <= TRN_TDST_RDY AFTER (TCQ)*1 ps; reg_tcfg_gnt <= USER_TCFG_GNT AFTER (TCQ)*1 ps; END IF; END IF; END PROCESS; ------------------------------------------------------------------------------ -- THROTTLE REASON: Block needs to transition to low power state PPM L1 -- - When to throttle: appropriate low power state signal asserted -- (architecture dependent) -- - When to stop: cfg_pcie_link_state goes to proper value (C_ROOT_PORT -- dependent) -- -- If the block needs to transition to PM state PPM L1, we need to finish -- up what we're doing and throttle immediately. ------------------------------------------------------------------------------ xhdl3 : IF ((C_FAMILY = "X7") AND (C_ROOT_PORT)) GENERATE -- PPM L1 signals for 7 Series in RC mode ppm_L1_trig <= '1' WHEN ((cfg_pcie_link_state_d = "000") AND (CFG_PCIE_LINK_STATE = "101")) ELSE '0'; ppm_L1_exit <= '1' WHEN (CFG_PCIE_LINK_STATE = "001") ELSE '0'; END GENERATE; -- PPM L1 signals for 7 Series in EP mode xhdl4 : IF (NOT((C_FAMILY = ("X7")) AND (C_ROOT_PORT))) GENERATE xhdl5 : IF ((C_FAMILY = ("X7")) AND (NOT(C_ROOT_PORT))) GENERATE ppm_L1_trig <= '1' WHEN ((cfg_pcie_link_state_d = "000") AND (CFG_PCIE_LINK_STATE = "101")) ELSE '0'; ppm_L1_exit <= '1' WHEN (CFG_PCIE_LINK_STATE = "000") ELSE '0'; END GENERATE; -- PPM L1 signals for V6 in RC mode xhdl6 : IF (NOT((C_FAMILY = ("X7")) AND (NOT(C_ROOT_PORT)))) GENERATE xhdl7 : IF ((C_FAMILY = ("V6")) AND (C_ROOT_PORT)) GENERATE ppm_L1_trig <= '1' WHEN ((TRN_RDLLP_DATA(31 DOWNTO 24) = x"20") AND TRN_RDLLP_SRC_RDY = '1' AND trn_rdllp_src_rdy_d = '0') ELSE '0'; ppm_L1_exit <= '1' WHEN (CFG_PCIE_LINK_STATE = "001") ELSE '0'; END GENERATE; -- PPM L1 signals for V6 in EP mode xhdl8 : IF (NOT((C_FAMILY = ("V6")) AND (C_ROOT_PORT))) GENERATE xhdl9 : IF ((C_FAMILY = ("V6")) AND (NOT(C_ROOT_PORT))) GENERATE ppm_L1_trig <= '1' WHEN (CFG_PMCSR_POWERSTATE /= "000") ELSE '0'; ppm_L1_exit <= '1' WHEN (CFG_PCIE_LINK_STATE = "000") ELSE '0'; END GENERATE; -- PPM L1 detection not supported for S6 xhdl10 : IF (NOT((C_FAMILY = ("V6")) AND (NOT(C_ROOT_PORT)))) GENERATE ppm_L1_trig <= '0'; ppm_L1_exit <= '1'; END GENERATE; END GENERATE; END GENERATE; END GENERATE; PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN ppm_L1_thrtl <= '0' AFTER (TCQ)*1 ps; cfg_pcie_link_state_d <= "000" AFTER (TCQ)*1 ps; trn_rdllp_src_rdy_d <= '0' AFTER (TCQ)*1 ps; ELSE IF (ppm_L1_trig = '1') THEN ppm_L1_thrtl <= '1' AFTER (TCQ)*1 ps; ELSIF (ppm_L1_exit = '1') THEN ppm_L1_thrtl <= '0' AFTER (TCQ)*1 ps; END IF; cfg_pcie_link_state_d <= CFG_PCIE_LINK_STATE AFTER (TCQ)*1 ps; trn_rdllp_src_rdy_d <= TRN_RDLLP_SRC_RDY AFTER (TCQ)*1 ps; END IF; END IF; END PROCESS; ------------------------------------------------------------------------------ -- THROTTLE REASON: Block needs to transition to low power state PPM L2/3 -- - When to throttle: appropriate PM signal indicates a transition to -- L2/3 is pending or in progress (family and role dependent) -- - When to stop: never (the only path out of L2/3 is a full reset) -- -- If the block needs to transition to PM state PPM L2/3, we need to finish -- up what we're doing and throttle when the user gives permission. ------------------------------------------------------------------------------ -- PPM L2/3 signals for 7 Series in RC mode xhdl11 : IF ((C_FAMILY = ("X7")) AND (C_ROOT_PORT)) GENERATE ppm_L23_trig <= '1' WHEN (cfg_pcie_link_state_d = "110") ELSE '0'; wire_to_turnoff <= '0'; END GENERATE; -- PPM L2/3 signals for V6 in RC mode xhdl12 : IF (NOT((C_FAMILY = ("X7")) AND (C_ROOT_PORT))) GENERATE xhdl13 : IF ((C_FAMILY = ("V6")) AND (C_ROOT_PORT)) GENERATE ppm_L23_trig <= CFG_PM_SEND_PME_TO; wire_to_turnoff <= '0'; END GENERATE; -- PPM L2/3 signals in EP mode xhdl14 : IF (NOT((C_FAMILY = ("V6")) AND (C_ROOT_PORT))) GENERATE ppm_L23_trig <= (wire_to_turnoff AND reg_turnoff_ok); -- PPM L2/3 signals for 7 Series in EP mode -- For 7 Series, cfg_to_turnoff pulses once when a turnoff request is -- outstanding, so we need a "sticky" register that grabs the request. xhdl15 : IF (C_FAMILY = ("X7")) GENERATE PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN reg_to_turnoff <= '0' AFTER (TCQ)*1 ps; ELSE IF (CFG_TO_TURNOFF = '1') THEN reg_to_turnoff <= '1' AFTER (TCQ)*1 ps; END IF; END IF; END IF; END PROCESS; wire_to_turnoff <= reg_to_turnoff; END GENERATE; -- PPM L2/3 signals for V6/S6 in EP mode -- In V6 and S6, the to_turnoff signal asserts and remains asserted until -- turnoff_ok is asserted, so a sticky reg is not necessary. xhdl16 : IF (NOT(C_FAMILY = ("X7"))) GENERATE wire_to_turnoff <= CFG_TO_TURNOFF; END GENERATE; PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN reg_turnoff_ok <= '0' AFTER (TCQ)*1 ps; ELSE reg_turnoff_ok <= USER_TURNOFF_OK AFTER (TCQ)*1 ps; END IF; END IF; END PROCESS; END GENERATE; END GENERATE; PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN ppm_L23_thrtl <= '0' AFTER (TCQ)*1 ps; cfg_turnoff_ok_pending <= '0' AFTER (TCQ)*1 ps; ELSE -- Make sure cfg_turnoff_ok pulses once for one clock cycle for every -- turnoff request. IF (ppm_L23_trig = '1') THEN ppm_L23_thrtl <= '1' AFTER (TCQ)*1 ps; END IF; IF (ppm_L23_trig = '1' AND (ppm_L23_thrtl = '0')) THEN cfg_turnoff_ok_pending <= '1' AFTER (TCQ)*1 ps; ELSIF (cfg_turnoff_ok_xhdl0 = '1') THEN cfg_turnoff_ok_pending <= '0' AFTER (TCQ)*1 ps; END IF; END IF; END IF; END PROCESS; -------------------------------------------------------------------------------- -- Create axi_thrtl_ok. This signal determines if it's OK to throttle the -- -- user design on the AXI interface. Since TREADY is registered, this signal -- -- needs to assert on the cycle ~before~ we actually intend to throttle. -- -- The only time it's OK to throttle when TVALID is asserted is on the first -- -- beat of a new packet. Therefore, assert axi_thrtl_ok if one of the -- -- is true: -- -- 1) The user is not in a packet and is not starting one -- -- 2) The user is just finishing a packet -- -- 3) We're already throttled, so it's OK to continue throttling -- -------------------------------------------------------------------------------- PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN reg_axi_in_pkt <= '0' AFTER (TCQ)*1 ps; ELSE IF (S_AXIS_TX_TVALID = '1' AND S_AXIS_TX_TLAST = '1') THEN reg_axi_in_pkt <= '0' AFTER (TCQ)*1 ps; ELSIF (tready_thrtl_xhdl1 = '1' AND S_AXIS_TX_TVALID = '1') THEN reg_axi_in_pkt <= '1' AFTER (TCQ)*1 ps; END IF; END IF; END IF; END PROCESS; axi_in_pkt <= (S_AXIS_TX_TVALID OR reg_axi_in_pkt); axi_pkt_ending <= (S_AXIS_TX_TVALID AND S_AXIS_TX_TLAST); axi_throttled <= NOT(tready_thrtl_xhdl1); axi_thrtl_ok <= (NOT(axi_in_pkt) OR axi_pkt_ending OR axi_throttled); -------------------------------------------------------------------------------- -- Throttle CTL State Machine: -- -- Throttle user design when a throttle trigger (or triggers) occur. -- -- Keep user throttled until all exit criteria have been met. -- -------------------------------------------------------------------------------- -- Immediate throttle signal. Used to "pounce" on a throttle opportunity when -- we're seeking one pre_throttle <= (tbuf_av_min_trig OR tbuf_av_gap_trig OR lnk_up_trig OR tcfg_req_trig OR ppm_L1_trig OR ppm_L23_trig); -- Registered throttle signals. Used to control throttle state machine reg_throttle <= (tbuf_av_min_thrtl OR tbuf_av_gap_thrtl OR lnk_up_thrtl OR tcfg_req_thrtl OR ppm_L1_thrtl OR ppm_L23_thrtl); exit_crit <= (NOT(tbuf_av_min_thrtl) AND NOT(tbuf_av_gap_thrtl) AND (NOT(lnk_up_thrtl)) AND (NOT(tcfg_req_thrtl)) AND (NOT(ppm_L1_thrtl)) AND (NOT(ppm_L23_thrtl))); PROCESS (CUR_STATE_A,reg_throttle, axi_thrtl_ok, tcfg_req_thrtl, tcfg_gnt_pending, cfg_turnoff_ok_pending, pre_throttle, exit_crit) BEGIN CASE CUR_STATE_A IS -- IDLE: in this state we're waiting for a trigger event to occur. As -- soon as an event occurs and the user isn't transmitting a packet, we -- throttle the PCIe block and the user and next state is THROTTLE. WHEN (IDLE) => IF(reg_throttle = '1' AND axi_thrtl_ok = '1') THEN tready_thrtl_mux <= '0'; NEXT_STATE_A <= (THROTTLE); -- Assert appropriate grant signal depending on the throttle type. IF (tcfg_req_thrtl = '1') THEN trn_tcfg_gnt_xhdl2 <= '1'; -- For cfg request, grant the request cfg_turnoff_ok_xhdl0 <= '0'; -- ELSIF (ppm_L23_thrtl = '1') THEN trn_tcfg_gnt_xhdl2 <= '0'; -- cfg_turnoff_ok_xhdl0 <= '1'; -- For PM request, permit transition ELSE trn_tcfg_gnt_xhdl2 <= '0'; -- Otherwise do nothing cfg_turnoff_ok_xhdl0 <= '0';-- END IF; ELSE -- If there's not throttle event, do nothing -- Throttle user as soon as possible tready_thrtl_mux <= (NOT((axi_thrtl_ok AND pre_throttle))); NEXT_STATE_A <= IDLE; trn_tcfg_gnt_xhdl2 <= '0'; cfg_turnoff_ok_xhdl0 <= '0'; END IF; -- THROTTLE: in this state the user is throttle and we're waiting for -- exit criteria, which tells us that the throttle event is over. When -- the exit criteria is satisfied, de-throttle the user and next state WHEN (THROTTLE) => IF (exit_crit = '1') THEN -- Dethrottle user tready_thrtl_mux <= (NOT(pre_throttle)); NEXT_STATE_A <= IDLE; ELSE -- Throttle user tready_thrtl_mux <= '0'; NEXT_STATE_A <= (THROTTLE); END IF; -- Assert appropriate grant signal depending on the throttle type. IF (tcfg_req_thrtl = '1' AND tcfg_gnt_pending = '1') THEN trn_tcfg_gnt_xhdl2 <= '1'; -- For cfg request, grant the request cfg_turnoff_ok_xhdl0 <= '0'; -- ELSIF (cfg_turnoff_ok_pending = '1') THEN trn_tcfg_gnt_xhdl2 <= '0'; -- cfg_turnoff_ok_xhdl0 <= '1'; -- For PM request, permit transition ELSE trn_tcfg_gnt_xhdl2 <= '0'; -- Otherwise do nothing cfg_turnoff_ok_xhdl0 <= '0'; -- END IF; WHEN OTHERS => tready_thrtl_mux <= '0'; NEXT_STATE_A <= (IDLE); trn_tcfg_gnt_xhdl2 <= '0' ; cfg_turnoff_ok_xhdl0 <= '0'; END CASE; END PROCESS; -- Synchronous logic PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN -- Throttle user by default until link comes up CUR_STATE_A <= (THROTTLE) AFTER (TCQ)*1 ps; reg_tlast <= '0' AFTER (TCQ)*1 ps; tready_thrtl_xhdl1 <= '0' AFTER (TCQ)*1 ps; ELSE CUR_STATE_A <= NEXT_STATE_A AFTER (TCQ)*1 ps; tready_thrtl_xhdl1 <= (tready_thrtl_mux AND NOT(tx_ecrc_pause)) AFTER (TCQ)*1 ps; reg_tlast <= S_AXIS_TX_TLAST AFTER (TCQ)*1 ps; END IF; END IF; END PROCESS; -- For X7, the PCIe block will generate the ECRC for a packet if trn_tecrc_gen -- is asserted at SOF. In this case, the Block needs an extra data beat to -- calculate the ECRC, but only if the following conditions are met: -- 1) there is no empty DWORDS at the end of the packet -- (i.e. packet length % C_DATA_WIDTH == 0) -- -- 2) There isn't a ECRC in the TLP already, as indicated by the TD bit in the -- TLP header -- -- If both conditions are met, the Block will stall the TRN interface for one -- data beat after EOF. We need to predict this stall and preemptively stall the -- User for one beat. xhdl17 : IF (C_FAMILY = ("X7")) GENERATE -- Grab necessary packet fields packet_fmt <= S_AXIS_TX_TDATA(30 DOWNTO 29); packet_td <= S_AXIS_TX_TDATA(15); -- Calculate total packet length header_len <= "100" WHEN packet_fmt(0) = '1' ELSE "011"; payload_len <= S_AXIS_TX_TDATA(9 DOWNTO 0) WHEN packet_fmt(1) = '1' ELSE "0000000000"; packet_len <= ("0000000000" & header_len) + ("0000" & payload_len); -- Determine if an ECRC pause is needed PACKET_LEN_CHECK_128 : IF (C_DATA_WIDTH = 128) GENERATE pause_needed <= '1' WHEN (packet_len(1 DOWNTO 0) = "00" AND packet_td = '0') ELSE '0'; END GENERATE; PACKET_LEN_CHECK_64 : IF (C_DATA_WIDTH /= 128) GENERATE pause_needed <= '1' WHEN (packet_len(0) = '0' AND packet_td = '0') ELSE '0'; END GENERATE; -- Create flag to alert TX pipeline to insert a stall tx_ecrc_pkt <= S_AXIS_TX_TUSER(0) AND pause_needed AND tready_thrtl_xhdl1 AND S_AXIS_TX_TVALID AND not(reg_axi_in_pkt); PROCESS (USER_CLK) BEGIN IF (USER_CLK'EVENT AND USER_CLK = '1') THEN IF (USER_RST = '1') THEN reg_tx_ecrc_pkt <= '0' AFTER (TCQ)*1 ps; ELSE IF (tx_ecrc_pkt = '1' AND S_AXIS_TX_TLAST = '0') THEN reg_tx_ecrc_pkt <= '1' AFTER (TCQ)*1 ps; ELSIF (tready_thrtl_xhdl1 = '1' AND S_AXIS_TX_TVALID = '1' AND S_AXIS_TX_TLAST = '1') THEN reg_tx_ecrc_pkt <= '0' AFTER (TCQ)*1 ps; END IF; END IF; END IF; END PROCESS; -- tx_ecrc_pkt <= (S_AXIS_TX_TUSER(0) AND tready_thrtl_xhdl1 AND S_AXIS_TX_TVALID AND (NOT(reg_axi_in_pkt))); tx_ecrc_pause <= (((tx_ecrc_pkt OR reg_tx_ecrc_pkt) AND S_AXIS_TX_TLAST AND S_AXIS_TX_TVALID AND tready_thrtl_xhdl1)); END GENERATE; xhdl18 : IF (NOT(C_FAMILY = ("X7"))) GENERATE tx_ecrc_pause <= '0'; END GENERATE; END trans;
Go to most recent revision | Compare with Previous | Blame | View Log