Subversion Repositories plasma

---------------------------------------------------------------------
-- TITLE: Register Bank
-- AUTHOR: Steve Rhoads (rhoadss@yahoo.com)
-- DATE CREATED: 2/2/01
-- FILENAME: reg_bank.vhd
-- PROJECT: Plasma CPU core
-- COPYRIGHT: Software placed into the public domain by the author.
--    Software 'as is' without warranty.  Author liable for nothing.
-- DESCRIPTION:
--    Implements a register bank with 32 registers that are 32-bits wide.
--    There are two read-ports and one write port.
---------------------------------------------------------------------
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
use work.mlite_pack.all;
 
entity reg_bank is
   generic(memory_type : string := "XILINX_16X");
   port(clk            : in  std_logic;
        reset_in       : in  std_logic;
        pause          : in  std_logic;
        rs_index       : in  std_logic_vector(5 downto 0);
        rt_index       : in  std_logic_vector(5 downto 0);
        rd_index       : in  std_logic_vector(5 downto 0);
        reg_source_out : out std_logic_vector(31 downto 0);
        reg_target_out : out std_logic_vector(31 downto 0);
        reg_dest_new   : in  std_logic_vector(31 downto 0);
        intr_enable    : out std_logic);
end; --entity reg_bank
 
 
--------------------------------------------------------------------
-- The ram_block architecture attempts to use TWO dual-port memories.
-- Different FPGAs and ASICs need different implementations.
-- Choose one of the RAM implementations below.
-- I need feedback on this section!
--------------------------------------------------------------------
architecture ram_block of reg_bank is
   signal intr_enable_reg : std_logic;
   type ram_type is array(31 downto 0) of std_logic_vector(31 downto 0);
 
   --controls access to dual-port memories
   signal addr_read1, addr_read2 : std_logic_vector(4 downto 0);
   signal addr_write             : std_logic_vector(4 downto 0);
   signal data_out1, data_out2   : std_logic_vector(31 downto 0);
   signal write_enable           : std_logic;
 
begin
 
reg_proc: process(clk, rs_index, rt_index, rd_index, reg_dest_new, 
      intr_enable_reg, data_out1, data_out2, reset_in, pause)
begin
   --setup for first dual-port memory
   if rs_index = "101110" then  --reg_epc CP0 14
      addr_read1 <= "00000";
   else
      addr_read1 <= rs_index(4 downto 0);
   end if;
   case rs_index is
   when "000000" => reg_source_out <= ZERO;
   when "101100" => reg_source_out <= ZERO(31 downto 1) & intr_enable_reg;
                    --interrupt vector address = 0x3c
   when "111111" => reg_source_out <= ZERO(31 downto 8) & "00111100";
   when others   => reg_source_out <= data_out1;
   end case;
 
   --setup for second dual-port memory
   addr_read2 <= rt_index(4 downto 0);
   case rt_index is
   when "000000" => reg_target_out <= ZERO;
   when others   => reg_target_out <= data_out2;
   end case;
 
   --setup write port for both dual-port memories
   if rd_index /= "000000" and rd_index /= "101100" and pause = '0' then
      write_enable <= '1';
   else
      write_enable <= '0';
   end if;
   if rd_index = "101110" then  --reg_epc CP0 14
      addr_write <= "00000";
   else
      addr_write <= rd_index(4 downto 0);
   end if;
 
   if reset_in = '1' then
      intr_enable_reg <= '0';
   elsif rising_edge(clk) then
      if rd_index = "101110" then     --reg_epc CP0 14
         intr_enable_reg <= '0';      --disable interrupts
      elsif rd_index = "101100" then
         intr_enable_reg <= reg_dest_new(0);
      end if;
   end if;
 
   intr_enable <= intr_enable_reg;
end process;
 
 
--------------------------------------------------------------
---- Pick only ONE of the dual-port RAM implementations below!
--------------------------------------------------------------
 
   -- Option #1
   -- One tri-port RAM, two read-ports, one write-port
   -- 32 registers 32-bits wide
   tri_port_mem:
   if memory_type = "TRI_PORT_X" generate
      ram_proc: process(clk, addr_read1, addr_read2, 
            addr_write, reg_dest_new, write_enable)
      variable tri_port_ram : ram_type := (others => ZERO);
      begin
         data_out1 <= tri_port_ram(conv_integer(addr_read1));
         data_out2 <= tri_port_ram(conv_integer(addr_read2));
         if rising_edge(clk) then
            if write_enable = '1' then
               tri_port_ram(conv_integer(addr_write)) := reg_dest_new;
            end if;
         end if;
      end process;
   end generate; --tri_port_mem
 
 
   -- Option #2
   -- Two dual-port RAMs, each with one read-port and one write-port
   dual_port_mem:
   if memory_type = "DUAL_PORT_" generate
      ram_proc2: process(clk, addr_read1, addr_read2, 
            addr_write, reg_dest_new, write_enable)
      variable dual_port_ram1 : ram_type := (others => ZERO);
      variable dual_port_ram2 : ram_type := (others => ZERO);
      begin
         data_out1 <= dual_port_ram1(conv_integer(addr_read1));
         data_out2 <= dual_port_ram2(conv_integer(addr_read2));
         if rising_edge(clk) then
            if write_enable = '1' then
               dual_port_ram1(conv_integer(addr_write)) := reg_dest_new;
               dual_port_ram2(conv_integer(addr_write)) := reg_dest_new;
            end if;
         end if;
      end process;
   end generate; --dual_port_mem
 
 
   -- Option #3
   -- RAM16X1D: 16 x 1 positive edge write, asynchronous read dual-port 
   -- distributed RAM for all Xilinx FPGAs
   -- From library UNISIM; use UNISIM.vcomponents.all;
   xilinx_16x1d:
   if memory_type = "XILINX_16X" generate
      signal data_out1A, data_out1B : std_logic_vector(31 downto 0);
      signal data_out2A, data_out2B : std_logic_vector(31 downto 0);
      signal weA, weB               : std_logic;
      signal no_connect             : std_logic_vector(127 downto 0);
   begin
      weA <= write_enable and not addr_write(4);  --lower 16 registers
      weB <= write_enable and addr_write(4);      --upper 16 registers
 
      reg_loop: for i in 0 to 31 generate
      begin
         --Read port 1 lower 16 registers
         reg_bit1a : RAM16X1D
         port map (
            WCLK  => clk,              -- Port A write clock input
            WE    => weA,              -- Port A write enable input
            A0    => addr_write(0),    -- Port A address[0] input bit
            A1    => addr_write(1),    -- Port A address[1] input bit
            A2    => addr_write(2),    -- Port A address[2] input bit
            A3    => addr_write(3),    -- Port A address[3] input bit
            D     => reg_dest_new(i),  -- Port A 1-bit data input
            DPRA0 => addr_read1(0),    -- Port B address[0] input bit
            DPRA1 => addr_read1(1),    -- Port B address[1] input bit
            DPRA2 => addr_read1(2),    -- Port B address[2] input bit
            DPRA3 => addr_read1(3),    -- Port B address[3] input bit
            DPO   => data_out1A(i),    -- Port B 1-bit data output
            SPO   => no_connect(i)     -- Port A 1-bit data output
         );
         --Read port 1 upper 16 registers
         reg_bit1b : RAM16X1D
         port map (
            WCLK  => clk,              -- Port A write clock input
            WE    => weB,              -- Port A write enable input
            A0    => addr_write(0),    -- Port A address[0] input bit
            A1    => addr_write(1),    -- Port A address[1] input bit
            A2    => addr_write(2),    -- Port A address[2] input bit
            A3    => addr_write(3),    -- Port A address[3] input bit
            D     => reg_dest_new(i),  -- Port A 1-bit data input
            DPRA0 => addr_read1(0),    -- Port B address[0] input bit
            DPRA1 => addr_read1(1),    -- Port B address[1] input bit
            DPRA2 => addr_read1(2),    -- Port B address[2] input bit
            DPRA3 => addr_read1(3),    -- Port B address[3] input bit
            DPO   => data_out1B(i),    -- Port B 1-bit data output
            SPO   => no_connect(32+i)  -- Port A 1-bit data output
         );
         --Read port 2 lower 16 registers
         reg_bit2a : RAM16X1D
         port map (
            WCLK  => clk,              -- Port A write clock input
            WE    => weA,              -- Port A write enable input
            A0    => addr_write(0),    -- Port A address[0] input bit
            A1    => addr_write(1),    -- Port A address[1] input bit
            A2    => addr_write(2),    -- Port A address[2] input bit
            A3    => addr_write(3),    -- Port A address[3] input bit
            D     => reg_dest_new(i),  -- Port A 1-bit data input
            DPRA0 => addr_read2(0),    -- Port B address[0] input bit
            DPRA1 => addr_read2(1),    -- Port B address[1] input bit
            DPRA2 => addr_read2(2),    -- Port B address[2] input bit
            DPRA3 => addr_read2(3),    -- Port B address[3] input bit
            DPO   => data_out2A(i),    -- Port B 1-bit data output
            SPO   => no_connect(64+i)  -- Port A 1-bit data output
         );
         --Read port 2 upper 16 registers
         reg_bit2b : RAM16X1D
         port map (
            WCLK  => clk,              -- Port A write clock input
            WE    => weB,              -- Port A write enable input
            A0    => addr_write(0),    -- Port A address[0] input bit
            A1    => addr_write(1),    -- Port A address[1] input bit
            A2    => addr_write(2),    -- Port A address[2] input bit
            A3    => addr_write(3),    -- Port A address[3] input bit
            D     => reg_dest_new(i),  -- Port A 1-bit data input
            DPRA0 => addr_read2(0),    -- Port B address[0] input bit
            DPRA1 => addr_read2(1),    -- Port B address[1] input bit
            DPRA2 => addr_read2(2),    -- Port B address[2] input bit
            DPRA3 => addr_read2(3),    -- Port B address[3] input bit
            DPO   => data_out2B(i),    -- Port B 1-bit data output
            SPO   => no_connect(96+i)  -- Port A 1-bit data output
         );
      end generate; --reg_loop
 
      data_out1 <= data_out1A when addr_read1(4)='0' else data_out1B;
      data_out2 <= data_out2A when addr_read2(4)='0' else data_out2B;
   end generate; --xilinx_16x1d
 
 
   -- Option #4
   -- Altera LPM_RAM_DP
   altera_mem:
   if memory_type = "ALTERA_LPM" generate
      signal clk_delayed : std_logic;
      signal addr_reg    : std_logic_vector(4 downto 0);
      signal data_reg    : std_logic_vector(31 downto 0);
      signal q1          : std_logic_vector(31 downto 0);
      signal q2          : std_logic_vector(31 downto 0);
   begin
      -- Altera dual port RAMs must have the addresses registered (sampled
      -- at the rising edge).  This is very unfortunate.
      -- Therefore, the dual port RAM read clock must delayed so that
      -- the read address signal can be sent from the mem_ctrl block.
      -- This solution also delays the how fast the registers are read so the 
      -- maximum clock speed is cut in half (12.5 MHz instead of 25 MHz).
 
      clk_delayed <= not clk;  --Could be delayed by 1/4 clock cycle instead
      dpram_bypass: process(clk, addr_write, reg_dest_new)
      begin
         if rising_edge(clk) and write_enable = '1' then
            addr_reg <= addr_write;
            data_reg <= reg_dest_new;
         end if;
      end process; --dpram_bypass
 
      -- Bypass dpram if reading what was just written (Altera limitation)
      data_out1 <= q1 when addr_read1 /= addr_reg else data_reg;
      data_out2 <= q2 when addr_read2 /= addr_reg else data_reg;
 
      lpm_ram_dp_component1 : lpm_ram_dp
      generic map (
         LPM_WIDTH => 32,
         LPM_WIDTHAD => 5,
         --LPM_NUMWORDS => 0,
         LPM_INDATA => "REGISTERED",
         LPM_OUTDATA => "UNREGISTERED",
         LPM_RDADDRESS_CONTROL => "REGISTERED",
         LPM_WRADDRESS_CONTROL => "REGISTERED",
         LPM_FILE => "UNUSED",
         LPM_TYPE => "LPM_RAM_DP",
         USE_EAB  => "ON",
         INTENDED_DEVICE_FAMILY => "UNUSED",
         RDEN_USED => "FALSE",
         LPM_HINT => "UNUSED")
      port map (
         RDCLOCK   => clk_delayed,
         RDCLKEN   => '1',
         RDADDRESS => addr_read1,
         RDEN      => '1',
         DATA      => reg_dest_new,
         WRADDRESS => addr_write,
         WREN      => write_enable,
         WRCLOCK   => clk,
         WRCLKEN   => '1',
         Q         => q1);
      lpm_ram_dp_component2 : lpm_ram_dp
      generic map (
         LPM_WIDTH => 32,
         LPM_WIDTHAD => 5,
         --LPM_NUMWORDS => 0,
         LPM_INDATA => "REGISTERED",
         LPM_OUTDATA => "UNREGISTERED",
         LPM_RDADDRESS_CONTROL => "REGISTERED",
         LPM_WRADDRESS_CONTROL => "REGISTERED",
         LPM_FILE => "UNUSED",
         LPM_TYPE => "LPM_RAM_DP",
         USE_EAB  => "ON",
         INTENDED_DEVICE_FAMILY => "UNUSED",
         RDEN_USED => "FALSE",
         LPM_HINT => "UNUSED")
      port map (
         RDCLOCK   => clk_delayed,
         RDCLKEN   => '1',
         RDADDRESS => addr_read2,
         RDEN      => '1',
         DATA      => reg_dest_new,
         WRADDRESS => addr_write,
         WREN      => write_enable,
         WRCLOCK   => clk,
         WRCLKEN   => '1',
         Q         => q2);
   end generate; --altera_mem
 
end; --architecture ram_block