Subversion Repositories rf68000

// ============================================================================
//        __
//   \\__/ o\    (C) 2022  Robert Finch, Waterloo
//    \  __ /    All rights reserved.
//     \/_//     robfinch<remove>@finitron.ca
//       ||
//
//      io_bitmap.sv
//
// BSD 3-Clause License
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// 1. Redistributions of source code must retain the above copyright notice, this
//    list of conditions and the following disclaimer.
//
// 2. Redistributions in binary form must reproduce the above copyright notice,
//    this list of conditions and the following disclaimer in the documentation
//    and/or other materials provided with the distribution.
//
// 3. Neither the name of the copyright holder nor the names of its
//    contributors may be used to endorse or promote products derived from
//    this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
// DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
// FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
// DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
// SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
// CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
// OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
// ============================================================================

module io_bitmap(rst_i, clk_i, cs_i, cyc_i, stb_i, ack_o, we_i, asid_i, adr_i, dat_i, dat_o,
        iocs_i, gate_o, gate_en);
input rst_i;
input clk_i;
input cs_i;
input cyc_i;
input stb_i;
output ack_o;
input we_i;
input [5:0] asid_i;
input [19:0] adr_i;
input [31:0] dat_i;
output reg [31:0] dat_o;
input iocs_i;
output reg gate_o;
output gate_en;

wire [31:0] douta, doutb;
reg ena, enb;

ack_gen #(
        .READ_STAGES(2),
        .WRITE_STAGES(1),
        .REGISTER_OUTPUT(1)
) uag1
(
        .rst_i(rst_i),
        .clk_i(clk_i),
        .ce_i(1'b1),
        .rid_i('d0),
        .wid_i('d0),
        .i(ena & ~we_i),
        .we_i(ena & we_i),
        .o(ack_o),
        .rid_o(),
        .wid_o()
);

ack_gen #(
        .READ_STAGES(2),
        .WRITE_STAGES(1),
        .REGISTER_OUTPUT(1)
) uag2
(
        .rst_i(rst_i),
        .clk_i(clk_i),
        .ce_i(1'b1),
        .rid_i('d0),
        .wid_i('d0),
        .i(enb & ~we_i),
        .we_i(enb & we_i),
        .o(gate_en),
        .rid_o(),
        .wid_o()
);

always_comb
        ena = cs_i & cyc_i & stb_i;
always_comb
        enb = iocs_i & cyc_i & stb_i;

   // xpm_memory_tdpram: True Dual Port RAM
   // Xilinx Parameterized Macro, version 2022.2

   xpm_memory_tdpram #(
      .ADDR_WIDTH_A(13),               // DECIMAL
      .ADDR_WIDTH_B(13),               // DECIMAL
      .AUTO_SLEEP_TIME(0),            // DECIMAL
      .BYTE_WRITE_WIDTH_A(32),        // DECIMAL
      .BYTE_WRITE_WIDTH_B(32),        // DECIMAL
      .CASCADE_HEIGHT(0),             // DECIMAL
      .CLOCKING_MODE("common_clock"), // String
      .ECC_MODE("no_ecc"),            // String
      .MEMORY_INIT_FILE("none"),      // String
      .MEMORY_INIT_PARAM("0"),        // String
      .MEMORY_OPTIMIZATION("true"),   // String
      .MEMORY_PRIMITIVE("auto"),      // String
      .MEMORY_SIZE(4096*64),          // DECIMAL
      .MESSAGE_CONTROL(0),            // DECIMAL
      .READ_DATA_WIDTH_A(32),         // DECIMAL
      .READ_DATA_WIDTH_B(32),         // DECIMAL
      .READ_LATENCY_A(2),             // DECIMAL
      .READ_LATENCY_B(1),             // DECIMAL
      .READ_RESET_VALUE_A("0"),       // String
      .READ_RESET_VALUE_B("0"),       // String
      .RST_MODE_A("SYNC"),            // String
      .RST_MODE_B("SYNC"),            // String
      .SIM_ASSERT_CHK(0),             // DECIMAL; 0=disable simulation messages, 1=enable simulation messages
      .USE_EMBEDDED_CONSTRAINT(0),    // DECIMAL
      .USE_MEM_INIT(1),               // DECIMAL
      .USE_MEM_INIT_MMI(0),           // DECIMAL
      .WAKEUP_TIME("disable_sleep"),  // String
      .WRITE_DATA_WIDTH_A(32),        // DECIMAL
      .WRITE_DATA_WIDTH_B(32),        // DECIMAL
      .WRITE_MODE_A("no_change"),     // String
      .WRITE_MODE_B("no_change"),     // String
      .WRITE_PROTECT(1)               // DECIMAL
   )
   xpm_memory_tdpram_inst (
      .dbiterra(),             // 1-bit output: Status signal to indicate double bit error occurrence
                                       // on the data output of port A.

      .dbiterrb(),             // 1-bit output: Status signal to indicate double bit error occurrence
                                       // on the data output of port A.

      .douta(douta),                   // READ_DATA_WIDTH_A-bit output: Data output for port A read operations.
      .doutb(doutb),                   // READ_DATA_WIDTH_B-bit output: Data output for port B read operations.
      .sbiterra(),             // 1-bit output: Status signal to indicate single bit error occurrence
                                       // on the data output of port A.

      .sbiterrb(),             // 1-bit output: Status signal to indicate single bit error occurrence
                                       // on the data output of port B.

      .addra({asid_i[5:0],adr_i[ 8: 2]}), // ADDR_WIDTH_A-bit input: Address for port A write and read operations.
      .addrb({asid_i[5:0],adr_i[19:13]}), // ADDR_WIDTH_B-bit input: Address for port B write and read operations.
      .clka(clk_i),                     // 1-bit input: Clock signal for port A. Also clocks port B when
                                       // parameter CLOCKING_MODE is "common_clock".

      .clkb(clk_i),                     // 1-bit input: Clock signal for port B when parameter CLOCKING_MODE is
                                       // "independent_clock". Unused when parameter CLOCKING_MODE is
                                       // "common_clock".

      .dina(dat_i),                     // WRITE_DATA_WIDTH_A-bit input: Data input for port A write operations.
      .dinb(32'h0),                     // WRITE_DATA_WIDTH_B-bit input: Data input for port B write operations.
      .ena(ena),                       // 1-bit input: Memory enable signal for port A. Must be high on clock
                                       // cycles when read or write operations are initiated. Pipelined
                                       // internally.

      .enb(enb),                       // 1-bit input: Memory enable signal for port B. Must be high on clock
                                       // cycles when read or write operations are initiated. Pipelined
                                       // internally.

      .injectdbiterra(1'b0), // 1-bit input: Controls double bit error injection on input data when
                                       // ECC enabled (Error injection capability is not available in
                                       // "decode_only" mode).

      .injectdbiterrb(1'b0), // 1-bit input: Controls double bit error injection on input data when
                                       // ECC enabled (Error injection capability is not available in
                                       // "decode_only" mode).

      .injectsbiterra(1'b0), // 1-bit input: Controls single bit error injection on input data when
                                       // ECC enabled (Error injection capability is not available in
                                       // "decode_only" mode).

      .injectsbiterrb(1'b0), // 1-bit input: Controls single bit error injection on input data when
                                       // ECC enabled (Error injection capability is not available in
                                       // "decode_only" mode).

      .regcea(1'b1),                 // 1-bit input: Clock Enable for the last register stage on the output
                                       // data path.

      .regceb(1'b1),                 // 1-bit input: Clock Enable for the last register stage on the output
                                       // data path.

      .rsta(1'b0),                     // 1-bit input: Reset signal for the final port A output register stage.
                                       // Synchronously resets output port douta to the value specified by
                                       // parameter READ_RESET_VALUE_A.

      .rstb(1'b0),                     // 1-bit input: Reset signal for the final port B output register stage.
                                       // Synchronously resets output port doutb to the value specified by
                                       // parameter READ_RESET_VALUE_B.

      .sleep(1'b0),                   // 1-bit input: sleep signal to enable the dynamic power saving feature.
      .wea(we_i),                       // WRITE_DATA_WIDTH_A/BYTE_WRITE_WIDTH_A-bit input: Write enable vector
                                       // for port A input data port dina. 1 bit wide when word-wide writes are
                                       // used. In byte-wide write configurations, each bit controls the
                                       // writing one byte of dina to address addra. For example, to
                                       // synchronously write only bits [15-8] of dina when WRITE_DATA_WIDTH_A
                                       // is 32, wea would be 4'b0010.

      .web(1'b0)                        // WRITE_DATA_WIDTH_B/BYTE_WRITE_WIDTH_B-bit input: Write enable vector
                                       // for port B input data port dinb. 1 bit wide when word-wide writes are
                                       // used. In byte-wide write configurations, each bit controls the
                                       // writing one byte of dinb to address addrb. For example, to
                                       // synchronously write only bits [15-8] of dinb when WRITE_DATA_WIDTH_B
                                       // is 32, web would be 4'b0010.

   );
                                
always_ff @(posedge clk_i)
        if (ena)
                dat_o <= douta;
        else
                dat_o <= 32'd0;

always_comb
        gate_o <= doutb[adr_i[12:8]];
                        
endmodule