OpenCores
URL https://opencores.org/ocsvn/s6soc/s6soc/trunk

Subversion Repositories s6soc

[/] [s6soc/] [trunk/] [sw/] [host/] [dumpuart.cpp] - Rev 47

Go to most recent revision | Compare with Previous | Blame | View Log

////////////////////////////////////////////////////////////////////////////////
//
// Filename:	dumpuart.cpp
//
// Project:	CMod S6 System on a Chip, ZipCPU demonstration project
//
// Purpose:	To produce any and all data from the UART port onto an output
//		pipe and/or an output file.  This replaces the minicom
//	interface.  This is necessary because 1) minicom can take a while to
//	set up, 2) the default interface is at 9600 Baud (not minicom's 
//	default), 3) this produces an unfiltered/unbuffered terminal output,
//	and 4) it also guarantees that output goes to a file (when requested).
//
// Creator:	Dan Gisselquist, Ph.D.
//		Gisselquist Technology, LLC
//
////////////////////////////////////////////////////////////////////////////////
//
// Copyright (C) 2015-2016, Gisselquist Technology, LLC
//
// This program is free software (firmware): you can redistribute it and/or
// modify it under the terms of  the GNU General Public License as published
// by the Free Software Foundation, either version 3 of the License, or (at
// your option) any later version.
//
// This program is distributed in the hope that it will be useful, but WITHOUT
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
//
// License:	GPL, v3, as defined and found on www.gnu.org,
//		http://www.gnu.org/licenses/gpl.html
//
//
////////////////////////////////////////////////////////////////////////////////
//
//
//
#include <stdio.h>
#include <stdlib.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#include <strings.h>
#include <ctype.h>
#include <string.h>
#include <signal.h>
#include <assert.h>
#include <termios.h>
 
int main(int argc, char **argv) {
	const char	*dev = argv[1];
	const	char	*fname = (argc>=3)?argv[2]:NULL;
	int	ttyfd = -1, dumpfd = -1;
 
	if (argc < 2) {
		fprintf(stderr, "USAGE: dumpuart /dev/tty... \n");
		exit(EXIT_FAILURE);
	}
 
	ttyfd = open(dev, O_RDONLY);
	if (ttyfd < 0) {
		fprintf(stderr, "Could not open device, %s\n", dev);
		exit(EXIT_FAILURE);
	}
	if (!isatty(ttyfd)) {
		fprintf(stderr, "Err: %s is not a terminal!\n", dev);
		exit(EXIT_FAILURE);
	}
 
	if (fname)
		dumpfd = open(fname, O_CREAT|O_TRUNC|O_WRONLY, 0644);
 
	// Set the baud rate ...
	{
		struct	termios tb;
 
		tcgetattr(ttyfd, &tb);
		// Set to raw mode
		cfmakeraw(&tb);
		// Non-canonical mode (no line editing ...)
		tb.c_lflag &= (~(ICANON));
		// Set no parity, 8 bit
		tb.c_cflag &= (~(CRTSCTS));
		// One stop bit
		tb.c_cflag &= (~(CSTOPB));
		// 9600 Baud
		cfsetspeed(&tb, B9600);
		// Block until at least one byte is available
		tb.c_cc[VMIN] = 1;
		tb.c_cc[VTIME] = 0;
		// Commit the changes
		tcsetattr(ttyfd, TCSANOW, &tb);
	}
 
	/*
	if (isatty(STDOUT_FILENO)) {
		struct	termios	tb;
		tcgetattr(STDOUT_FILENO, &tb);
	}
	*/
 
	char	buf[64];
	int	nr;
 
	while((nr=read(ttyfd, buf, sizeof(buf)))>0) {
		if (dumpfd >= 0)
			write(dumpfd, buf, nr);
		write(STDOUT_FILENO, buf, nr);
	}
 
	close(ttyfd);
	if (dumpfd >= 0)
		close(dumpfd);
}
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.