URL
https://opencores.org/ocsvn/sdr_ctrl/sdr_ctrl/trunk
Subversion Repositories sdr_ctrl
[/] [sdr_ctrl/] [trunk/] [rtl/] [core/] [sdrc_core.v] - Rev 11
Go to most recent revision | Compare with Previous | Blame | View Log
/********************************************************************* SDRAM Controller Core File This file is part of the sdram controller project http://www.opencores.org/cores/sdr_ctrl/ Description: SDRAM Controller Core Module 2 types of SDRAMs are supported, 1Mx16 2 bank, or 4Mx16 4 bank. This block integrate following sub modules sdrc_bs_convert convert the system side 32 bit into equvailent 16/32 SDR format sdrc_req_gen This module takes requests from the app, chops them to burst booundaries if wrap=0, decodes the bank and passe the request to bank_ctl sdrc_xfr_ctl This module takes requests from sdr_bank_ctl, runs the transfer and controls data flow to/from the app. At the end of the transfer it issues a burst terminate if not at the end of a burst and another command to this bank is not available. sdrc_bank_ctl This module takes requests from sdr_req_gen, checks for page hit/miss and issues precharge/activate commands and then passes the request to sdr_xfr_ctl. Assumption: SDRAM Pads should be placed near to this module. else user should add a FF near the pads To Do: nothing Author(s): - Dinesh Annayya, dinesha@opencores.org Version : 1.0 - 8th Jan 2012 Copyright (C) 2000 Authors and OPENCORES.ORG This source file may be used and distributed without restriction provided that this copyright statement is not removed from the file and that any derivative work contains the original copyright notice and the associated disclaimer. This source file is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This source is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this source; if not, download it from http://www.opencores.org/lgpl.shtml *******************************************************************/ `include "sdrc.def" module sdrc_core ( clk, pad_clk, reset_n, sdr_width, /* Request from app */ app_req, // Transfer Request app_req_addr, // SDRAM Address app_req_addr_mask, // Address mask for queue wrap app_req_len, // Burst Length (in 16 bit words) app_req_wrap, // Wrap mode request (xfr_len = 4) app_req_wr_n, // 0 => Write request, 1 => read req app_req_ack, // Request has been accepted sdr_core_busy_n, // OK to arbitrate next request cfg_req_depth, //how many req. buffer should hold app_wr_data, app_wr_en_n, app_rd_data, app_rd_valid, app_wr_next_req, sdr_init_done, app_req_dma_last, /* Interface to SDRAMs */ sdr_cs_n, sdr_cke, sdr_ras_n, sdr_cas_n, sdr_we_n, sdr_dqm, sdr_ba, sdr_addr, pad_sdr_din, sdr_dout, sdr_den_n, /* Parameters */ cfg_sdr_en, cfg_sdr_dev_config, // using 64M/4bank SDRAMs cfg_sdr_mode_reg, cfg_sdr_tras_d, cfg_sdr_trp_d, cfg_sdr_trcd_d, cfg_sdr_cas, cfg_sdr_trcar_d, cfg_sdr_twr_d, cfg_sdr_rfsh, cfg_sdr_rfmax); parameter APP_AW = 30; // Application Address Width parameter APP_DW = 32; // Application Data Width parameter APP_BW = 4; // Application Byte Width parameter APP_RW = 9; // Application Request Width parameter SDR_DW = 16; // SDR Data Width parameter SDR_BW = 2; // SDR Byte Width //----------------------------------------------- // Global Variable // ---------------------------------------------- input clk ; // SDRAM Clock input pad_clk ; // SDRAM Clock from Pad, used for registering Read Data input reset_n ; // Reset Signal input sdr_width ; // 0 - 32 Bit SDR, 1 - 16 Bit SDR //------------------------------------------------ // Request from app //------------------------------------------------ input app_req ; // Application Request input [APP_AW-1:0] app_req_addr ; // Address input [APP_AW-2:0] app_req_addr_mask ; // Address Mask input app_req_wr_n ; // 0 - Write, 1 - Read input app_req_wrap ; // Address Wrap output app_req_ack ; // Application Request Ack output sdr_core_busy_n ; // 0 - busy, 1 - free input [APP_DW-1:0] app_wr_data ; // Write Data output app_wr_next_req ; // Next Write Data Request input [APP_BW-1:0] app_wr_en_n ; // Byte wise Write Enable output [APP_DW-1:0] app_rd_data ; // Read Data output app_rd_valid ; // Read Valid //------------------------------------------------ // Interface to SDRAMs //------------------------------------------------ output sdr_cke ; // SDRAM CKE output sdr_cs_n ; // SDRAM Chip Select output sdr_ras_n ; // SDRAM ras output sdr_cas_n ; // SDRAM cas output sdr_we_n ; // SDRAM write enable output [SDR_BW-1:0] sdr_dqm ; // SDRAM Data Mask output [1:0] sdr_ba ; // SDRAM Bank Enable output [11:0] sdr_addr ; // SDRAM Address input [SDR_DW-1:0] pad_sdr_din ; // SDRA Data Input output [SDR_DW-1:0] sdr_dout ; // SDRAM Data Output output [SDR_BW-1:0] sdr_den_n ; // SDRAM Data Output enable //------------------------------------------------ // Configuration Parameter //------------------------------------------------ output sdr_init_done ; input [3:0] cfg_sdr_tras_d ; input [3:0] cfg_sdr_trp_d ; input [3:0] cfg_sdr_trcd_d ; input cfg_sdr_en ; input [1:0] cfg_sdr_dev_config ; // 2'b00 - 8 MB, 01 - 16 MB, 10 - 32 MB , 11 - 64 MB input [1:0] cfg_req_depth ; input [APP_RW-1:0] app_req_len ; input [11:0] cfg_sdr_mode_reg ; input [2:0] cfg_sdr_cas ; input [3:0] cfg_sdr_trcar_d ; input [3:0] cfg_sdr_twr_d ; input [`SDR_RFSH_TIMER_W-1 : 0] cfg_sdr_rfsh; input [`SDR_RFSH_ROW_CNT_W -1 : 0] cfg_sdr_rfmax; input app_req_dma_last; // this signal should close the bank /****************************************************************************/ // Internal Nets // SDR_REQ_GEN wire r2x_idle, app_req_ack,app_req_ack_int; wire app_req_dma_last_int; wire r2b_req, r2b_start, r2b_last, r2b_write; wire [`SDR_REQ_ID_W-1:0]r2b_req_id; wire [1:0] r2b_ba; wire [11:0] r2b_raddr; wire [11:0] r2b_caddr; wire [APP_RW-1:0] r2b_len; // SDR BANK CTL wire b2r_ack, b2x_idle; wire b2x_req, b2x_start, b2x_last, b2x_tras_ok; wire [`SDR_REQ_ID_W-1:0]b2x_id; wire [1:0] b2x_ba; wire b2x_ba_last; wire [11:0] b2x_addr; wire [APP_RW-1:0] b2x_len; wire [1:0] b2x_cmd; // SDR_XFR_CTL wire x2b_ack; wire [3:0] x2b_pre_ok; wire x2b_refresh, x2b_act_ok, x2b_rdok, x2b_wrok; wire xfr_rdstart, xfr_rdlast; wire xfr_wrstart, xfr_wrlast; wire [`SDR_REQ_ID_W-1:0]xfr_id; wire [13:0] xfr_addr_msb; wire [APP_DW-1:0] app_rd_data; wire app_wr_next_req, app_rd_valid; wire sdr_cs_n, sdr_cke, sdr_ras_n, sdr_cas_n, sdr_we_n; wire [SDR_BW-1:0] sdr_dqm; wire [1:0] sdr_ba; wire [11:0] sdr_addr; wire [SDR_DW-1:0] sdr_dout; wire [SDR_DW-1:0] sdr_dout_int; wire [SDR_BW-1:0] sdr_den_n; wire [SDR_BW-1:0] sdr_den_n_int; wire [1:0] xfr_bank_sel; wire [1:0] cfg_sdr_dev_config; wire [APP_AW:0] app_req_addr_int; wire [APP_AW-1:0] app_req_addr; wire [APP_RW-1:0] app_req_len_int; wire [APP_RW-1:0] app_req_len; wire [APP_DW-1:0] app_wr_data; wire [SDR_DW-1:0] add_wr_data_int; wire [APP_BW-1:0] app_wr_en_n; wire [SDR_BW-1:0] app_wr_en_n_int; //wire [31:0] app_rd_data; wire [SDR_DW-1:0] app_rd_data_int; // wire app_req_int; wire r2b_wrap; wire b2r_arb_ok; wire b2x_wrap; wire app_wr_next_int; wire app_rd_valid_int; // synopsys translate_off wire [3:0] sdr_cmd; assign sdr_cmd = {sdr_cs_n, sdr_ras_n, sdr_cas_n, sdr_we_n}; // synopsys translate_on assign sdr_den_n = sdr_width ? {2'b00,sdr_den_n_int[1:0]} : sdr_den_n_int; assign sdr_dout = sdr_width ? {16'h0000,sdr_dout_int[15:0]} : sdr_dout_int; /****************************************************************************/ // Instantiate sdr_req_gen // This module takes requests from the app, chops them to burst booundaries // if wrap=0, decodes the bank and passe the request to bank_ctl sdrc_req_gen #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_req_gen ( .clk (clk ), .reset_n (reset_n ), .sdr_dev_config (cfg_sdr_dev_config ), /* Request from app */ .r2x_idle (r2x_idle ), .req (app_req_int ), .req_id (4'b0 ), .req_addr (app_req_addr_int ), .req_addr_mask (app_req_addr_mask ), .req_len (app_req_len_int ), .req_wrap (app_req_wrap ), .req_wr_n (app_req_wr_n ), .req_ack (app_req_ack_int ), .sdr_core_busy_n (sdr_core_busy_n ), /* Req to bank_ctl */ .r2b_req (r2b_req ), .r2b_req_id (r2b_req_id ), .r2b_start (r2b_start ), .r2b_last (r2b_last ), .r2b_wrap (r2b_wrap ), .r2b_ba (r2b_ba ), .r2b_raddr (r2b_raddr ), .r2b_caddr (r2b_caddr ), .r2b_len (r2b_len ), .r2b_write (r2b_write ), .b2r_ack (b2r_ack ), .b2r_arb_ok (b2r_arb_ok ), .sdr_width (sdr_width ), .sdr_init_done (sdr_init_done ) ); /****************************************************************************/ // Instantiate sdr_bank_ctl // This module takes requests from sdr_req_gen, checks for page hit/miss and // issues precharge/activate commands and then passes the request to // sdr_xfr_ctl. sdrc_bank_ctl #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_bank_ctl ( .clk (clk ), .reset_n (reset_n ), .a2b_req_depth (cfg_req_depth ), /* Req from req_gen */ .r2b_req (r2b_req ), .r2b_req_id (r2b_req_id ), .r2b_start (r2b_start ), .r2b_last (r2b_last ), .r2b_wrap (r2b_wrap ), .r2b_ba (r2b_ba ), .r2b_raddr (r2b_raddr ), .r2b_caddr (r2b_caddr ), .r2b_len (r2b_len ), .r2b_write (r2b_write ), .b2r_arb_ok (b2r_arb_ok ), .b2r_ack (b2r_ack ), /* Transfer request to xfr_ctl */ .b2x_idle (b2x_idle ), .b2x_req (b2x_req ), .b2x_start (b2x_start ), .b2x_last (b2x_last ), .b2x_wrap (b2x_wrap ), .b2x_id (b2x_id ), .b2x_ba (b2x_ba ), .b2x_addr (b2x_addr ), .b2x_len (b2x_len ), .b2x_cmd (b2x_cmd ), .x2b_ack (x2b_ack ), /* Status from xfr_ctl */ .b2x_tras_ok (b2x_tras_ok ), .x2b_refresh (x2b_refresh ), .x2b_pre_ok (x2b_pre_ok ), .x2b_act_ok (x2b_act_ok ), .x2b_rdok (x2b_rdok ), .x2b_wrok (x2b_wrok ), /* for generate cuurent xfr address msb */ .sdr_dev_config (cfg_sdr_dev_config ), .sdr_req_norm_dma_last(app_req_dma_last_int), .xfr_bank_sel (xfr_bank_sel ), .xfr_addr_msb (xfr_addr_msb ), /* SDRAM Timing */ .tras_delay (cfg_sdr_tras_d ), .trp_delay (cfg_sdr_trp_d ), .trcd_delay (cfg_sdr_trcd_d ) ); /****************************************************************************/ // Instantiate sdr_xfr_ctl // This module takes requests from sdr_bank_ctl, runs the transfer and // controls data flow to/from the app. At the end of the transfer it issues a // burst terminate if not at the end of a burst and another command to this // bank is not available. sdrc_xfr_ctl #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_xfr_ctl ( .clk (clk ), .reset_n (reset_n ), /* Transfer request from bank_ctl */ .r2x_idle (r2x_idle ), .b2x_idle (b2x_idle ), .b2x_req (b2x_req ), .b2x_start (b2x_start ), .b2x_last (b2x_last ), .b2x_wrap (b2x_wrap ), .b2x_id (b2x_id ), .b2x_ba (b2x_ba ), .b2x_addr (b2x_addr ), .b2x_len (b2x_len ), .b2x_cmd (b2x_cmd ), .x2b_ack (x2b_ack ), /* Status to bank_ctl, req_gen */ .b2x_tras_ok (b2x_tras_ok ), .x2b_refresh (x2b_refresh ), .x2b_pre_ok (x2b_pre_ok ), .x2b_act_ok (x2b_act_ok ), .x2b_rdok (x2b_rdok ), .x2b_wrok (x2b_wrok ), /* SDRAM I/O */ .sdr_cs_n (sdr_cs_n ), .sdr_cke (sdr_cke ), .sdr_ras_n (sdr_ras_n ), .sdr_cas_n (sdr_cas_n ), .sdr_we_n (sdr_we_n ), .sdr_dqm (sdr_dqm ), .sdr_ba (sdr_ba ), .sdr_addr (sdr_addr ), .sdr_din (pad_sdr_din ), .sdr_dout (sdr_dout_int ), .sdr_den_n (sdr_den_n_int ), /* Data Flow to the app */ .x2a_rdstart (xfr_rdstart ), .x2a_wrstart (xfr_wrstart ), .x2a_id (xfr_id ), .x2a_rdlast (xfr_rdlast ), .x2a_wrlast (xfr_wrlast ), .app_wrdt (add_wr_data_int ), .app_wren_n (app_wr_en_n_int ), .x2a_wrnext (app_wr_next_int ), .x2a_rddt (app_rd_data_int ), .x2a_rdok (app_rd_valid_int ), .sdr_init_done (sdr_init_done ), /* SDRAM Parameters */ .sdram_enable (cfg_sdr_en ), .sdram_mode_reg (cfg_sdr_mode_reg ), /* current xfr bank */ .xfr_bank_sel (xfr_bank_sel ), /* SDRAM Timing */ .cas_latency (cfg_sdr_cas ), .trp_delay (cfg_sdr_trp_d ), .trcar_delay (cfg_sdr_trcar_d ), .twr_delay (cfg_sdr_twr_d ), .rfsh_time (cfg_sdr_rfsh ), .rfsh_rmax (cfg_sdr_rfmax ) ); sdrc_bs_convert #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_bs_convert ( .clk (clk ), .reset_n (reset_n ), .sdr_width (sdr_width ), .app_req_addr (app_req_addr ), .app_req_addr_int (app_req_addr_int ), .app_req_len (app_req_len ), .app_req_len_int (app_req_len_int ), .app_sdr_req (app_req ), .app_sdr_req_int (app_req_int ), .app_req_dma_last (app_req_dma_last ), .app_req_dma_last_int(app_req_dma_last_int), .app_req_wr_n (app_req_wr_n ), .app_req_ack_int (app_req_ack_int ), .app_req_ack (app_req_ack ), .app_wr_data (app_wr_data ), .app_wr_data_int (add_wr_data_int ), .app_wr_en_n (app_wr_en_n ), .app_wr_en_n_int (app_wr_en_n_int ), .app_wr_next_int (app_wr_next_int ), .app_wr_next (app_wr_next_req ), .app_rd_data_int (app_rd_data_int ), .app_rd_data (app_rd_data ), .app_rd_valid_int (app_rd_valid_int ), .app_rd_valid (app_rd_valid ) ); endmodule // sdrc_core
Go to most recent revision | Compare with Previous | Blame | View Log