URL
https://opencores.org/ocsvn/sdr_ctrl/sdr_ctrl/trunk
Subversion Repositories sdr_ctrl
[/] [sdr_ctrl/] [trunk/] [rtl/] [core/] [sdrc_core.v] - Rev 71
Go to most recent revision | Compare with Previous | Blame | View Log
/********************************************************************* SDRAM Controller Core File This file is part of the sdram controller project http://www.opencores.org/cores/sdr_ctrl/ Description: SDRAM Controller Core Module 2 types of SDRAMs are supported, 1Mx16 2 bank, or 4Mx16 4 bank. This block integrate following sub modules sdrc_bs_convert convert the system side 32 bit into equvailent 8/16/32 SDR format sdrc_req_gen This module takes requests from the app, chops them to burst booundaries if wrap=0, decodes the bank and passe the request to bank_ctl sdrc_xfr_ctl This module takes requests from sdr_bank_ctl, runs the transfer and controls data flow to/from the app. At the end of the transfer it issues a burst terminate if not at the end of a burst and another command to this bank is not available. sdrc_bank_ctl This module takes requests from sdr_req_gen, checks for page hit/miss and issues precharge/activate commands and then passes the request to sdr_xfr_ctl. Assumption: SDRAM Pads should be placed near to this module. else user should add a FF near the pads To Do: nothing Author(s): - Dinesh Annayya, dinesha@opencores.org Version : 0.0 - 8th Jan 2012 Initial version with 16/32 Bit SDRAM Support : 0.1 - 24th Jan 2012 8 Bit SDRAM Support is added 0.2 - 2nd Feb 2012 Improved the command pipe structure to accept up-to 4 command of different bank. 0.3 - 7th Feb 2012 Bug fix for parameter defination for request length has changed from 9 to 12 0.4 - 26th April 2013 SDRAM Address Bit is Extended by 12 bit to 13 bit to support higher SDRAM Copyright (C) 2000 Authors and OPENCORES.ORG This source file may be used and distributed without restriction provided that this copyright statement is not removed from the file and that any derivative work contains the original copyright notice and the associated disclaimer. This source file is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This source is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this source; if not, download it from http://www.opencores.org/lgpl.shtml *******************************************************************/ `include "sdrc_define.v" module sdrc_core ( clk, pad_clk, reset_n, sdr_width, cfg_colbits, /* Request from app */ app_req, // Transfer Request app_req_addr, // SDRAM Address app_req_len, // Burst Length (in 16 bit words) app_req_wrap, // Wrap mode request (xfr_len = 4) app_req_wr_n, // 0 => Write request, 1 => read req app_req_ack, // Request has been accepted cfg_req_depth, //how many req. buffer should hold app_wr_data, app_wr_en_n, app_last_wr, app_rd_data, app_rd_valid, app_last_rd, app_wr_next_req, sdr_init_done, app_req_dma_last, /* Interface to SDRAMs */ sdr_cs_n, sdr_cke, sdr_ras_n, sdr_cas_n, sdr_we_n, sdr_dqm, sdr_ba, sdr_addr, pad_sdr_din, sdr_dout, sdr_den_n, /* Parameters */ cfg_sdr_en, cfg_sdr_mode_reg, cfg_sdr_tras_d, cfg_sdr_trp_d, cfg_sdr_trcd_d, cfg_sdr_cas, cfg_sdr_trcar_d, cfg_sdr_twr_d, cfg_sdr_rfsh, cfg_sdr_rfmax); parameter APP_AW = 26; // Application Address Width parameter APP_DW = 32; // Application Data Width parameter APP_BW = 4; // Application Byte Width parameter APP_RW = 9; // Application Request Width parameter SDR_DW = 16; // SDR Data Width parameter SDR_BW = 2; // SDR Byte Width //----------------------------------------------- // Global Variable // ---------------------------------------------- input clk ; // SDRAM Clock input pad_clk ; // SDRAM Clock from Pad, used for registering Read Data input reset_n ; // Reset Signal input [1:0] sdr_width ; // 2'b00 - 32 Bit SDR, 2'b01 - 16 Bit SDR, 2'b1x - 8 Bit input [1:0] cfg_colbits ; // 2'b00 - 8 Bit column address, 2'b01 - 9 Bit, 10 - 10 bit, 11 - 11Bits //------------------------------------------------ // Request from app //------------------------------------------------ input app_req ; // Application Request input [APP_AW-1:0] app_req_addr ; // Address input app_req_wr_n ; // 0 - Write, 1 - Read input app_req_wrap ; // Address Wrap output app_req_ack ; // Application Request Ack input [APP_DW-1:0] app_wr_data ; // Write Data output app_wr_next_req ; // Next Write Data Request input [APP_BW-1:0] app_wr_en_n ; // Byte wise Write Enable output app_last_wr ; // Last Write trannsfer of a given Burst output [APP_DW-1:0] app_rd_data ; // Read Data output app_rd_valid ; // Read Valid output app_last_rd ; // Last Read Transfer of a given Burst //------------------------------------------------ // Interface to SDRAMs //------------------------------------------------ output sdr_cke ; // SDRAM CKE output sdr_cs_n ; // SDRAM Chip Select output sdr_ras_n ; // SDRAM ras output sdr_cas_n ; // SDRAM cas output sdr_we_n ; // SDRAM write enable output [SDR_BW-1:0] sdr_dqm ; // SDRAM Data Mask output [1:0] sdr_ba ; // SDRAM Bank Enable output [12:0] sdr_addr ; // SDRAM Address input [SDR_DW-1:0] pad_sdr_din ; // SDRA Data Input output [SDR_DW-1:0] sdr_dout ; // SDRAM Data Output output [SDR_BW-1:0] sdr_den_n ; // SDRAM Data Output enable //------------------------------------------------ // Configuration Parameter //------------------------------------------------ output sdr_init_done ; // Indicate SDRAM Initialisation Done input [3:0] cfg_sdr_tras_d ; // Active to precharge delay input [3:0] cfg_sdr_trp_d ; // Precharge to active delay input [3:0] cfg_sdr_trcd_d ; // Active to R/W delay input cfg_sdr_en ; // Enable SDRAM controller input [1:0] cfg_req_depth ; // Maximum Request accepted by SDRAM controller input [APP_RW-1:0] app_req_len ; // Application Burst Request length in 32 bit input [12:0] cfg_sdr_mode_reg ; input [2:0] cfg_sdr_cas ; // SDRAM CAS Latency input [3:0] cfg_sdr_trcar_d ; // Auto-refresh period input [3:0] cfg_sdr_twr_d ; // Write recovery delay input [`SDR_RFSH_TIMER_W-1 : 0] cfg_sdr_rfsh; input [`SDR_RFSH_ROW_CNT_W -1 : 0] cfg_sdr_rfmax; input app_req_dma_last; // this signal should close the bank /****************************************************************************/ // Internal Nets // SDR_REQ_GEN wire [`SDR_REQ_ID_W-1:0]r2b_req_id; wire [1:0] r2b_ba; wire [12:0] r2b_raddr; wire [12:0] r2b_caddr; wire [`REQ_BW-1:0] r2b_len; // SDR BANK CTL wire [`SDR_REQ_ID_W-1:0]b2x_id; wire [1:0] b2x_ba; wire [12:0] b2x_addr; wire [`REQ_BW-1:0] b2x_len; wire [1:0] b2x_cmd; // SDR_XFR_CTL wire [3:0] x2b_pre_ok; wire [`SDR_REQ_ID_W-1:0]xfr_id; wire [APP_DW-1:0] app_rd_data; wire sdr_cs_n, sdr_cke, sdr_ras_n, sdr_cas_n, sdr_we_n; wire [SDR_BW-1:0] sdr_dqm; wire [1:0] sdr_ba; wire [12:0] sdr_addr; wire [SDR_DW-1:0] sdr_dout; wire [SDR_DW-1:0] sdr_dout_int; wire [SDR_BW-1:0] sdr_den_n; wire [SDR_BW-1:0] sdr_den_n_int; wire [1:0] xfr_bank_sel; wire [APP_AW-1:0] app_req_addr; wire [APP_RW-1:0] app_req_len; wire [APP_DW-1:0] app_wr_data; wire [SDR_DW-1:0] a2x_wrdt ; wire [APP_BW-1:0] app_wr_en_n; wire [SDR_BW-1:0] a2x_wren_n; //wire [31:0] app_rd_data; wire [SDR_DW-1:0] x2a_rddt; // synopsys translate_off wire [3:0] sdr_cmd; assign sdr_cmd = {sdr_cs_n, sdr_ras_n, sdr_cas_n, sdr_we_n}; // synopsys translate_on assign sdr_den_n = sdr_den_n_int ; assign sdr_dout = sdr_dout_int ; // To meet the timing at read path, read data is registered w.r.t pad_sdram_clock and register back to sdram_clk // assumption, pad_sdram_clk is synhronous and delayed clock of sdram_clk. // register w.r.t pad sdram clk reg [SDR_DW-1:0] pad_sdr_din1; reg [SDR_DW-1:0] pad_sdr_din2; always@(posedge pad_clk) begin pad_sdr_din1 <= pad_sdr_din; end always@(posedge clk) begin pad_sdr_din2 <= pad_sdr_din1; end /****************************************************************************/ // Instantiate sdr_req_gen // This module takes requests from the app, chops them to burst booundaries // if wrap=0, decodes the bank and passe the request to bank_ctl sdrc_req_gen #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_req_gen ( .clk (clk ), .reset_n (reset_n ), .cfg_colbits (cfg_colbits ), .sdr_width (sdr_width ), /* Req to xfr_ctl */ .r2x_idle (r2x_idle ), /* Request from app */ .req (app_req ), .req_id (4'b0 ), .req_addr (app_req_addr ), .req_len (app_req_len ), .req_wrap (app_req_wrap ), .req_wr_n (app_req_wr_n ), .req_ack (app_req_ack ), /* Req to bank_ctl */ .r2b_req (r2b_req ), .r2b_req_id (r2b_req_id ), .r2b_start (r2b_start ), .r2b_last (r2b_last ), .r2b_wrap (r2b_wrap ), .r2b_ba (r2b_ba ), .r2b_raddr (r2b_raddr ), .r2b_caddr (r2b_caddr ), .r2b_len (r2b_len ), .r2b_write (r2b_write ), .b2r_ack (b2r_ack ), .b2r_arb_ok (b2r_arb_ok ) ); /****************************************************************************/ // Instantiate sdr_bank_ctl // This module takes requests from sdr_req_gen, checks for page hit/miss and // issues precharge/activate commands and then passes the request to // sdr_xfr_ctl. sdrc_bank_ctl #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_bank_ctl ( .clk (clk ), .reset_n (reset_n ), .a2b_req_depth (cfg_req_depth ), /* Req from req_gen */ .r2b_req (r2b_req ), .r2b_req_id (r2b_req_id ), .r2b_start (r2b_start ), .r2b_last (r2b_last ), .r2b_wrap (r2b_wrap ), .r2b_ba (r2b_ba ), .r2b_raddr (r2b_raddr ), .r2b_caddr (r2b_caddr ), .r2b_len (r2b_len ), .r2b_write (r2b_write ), .b2r_arb_ok (b2r_arb_ok ), .b2r_ack (b2r_ack ), /* Transfer request to xfr_ctl */ .b2x_idle (b2x_idle ), .b2x_req (b2x_req ), .b2x_start (b2x_start ), .b2x_last (b2x_last ), .b2x_wrap (b2x_wrap ), .b2x_id (b2x_id ), .b2x_ba (b2x_ba ), .b2x_addr (b2x_addr ), .b2x_len (b2x_len ), .b2x_cmd (b2x_cmd ), .x2b_ack (x2b_ack ), /* Status from xfr_ctl */ .b2x_tras_ok (b2x_tras_ok ), .x2b_refresh (x2b_refresh ), .x2b_pre_ok (x2b_pre_ok ), .x2b_act_ok (x2b_act_ok ), .x2b_rdok (x2b_rdok ), .x2b_wrok (x2b_wrok ), /* for generate cuurent xfr address msb */ .sdr_req_norm_dma_last(app_req_dma_last), .xfr_bank_sel (xfr_bank_sel ), /* SDRAM Timing */ .tras_delay (cfg_sdr_tras_d ), .trp_delay (cfg_sdr_trp_d ), .trcd_delay (cfg_sdr_trcd_d ) ); /****************************************************************************/ // Instantiate sdr_xfr_ctl // This module takes requests from sdr_bank_ctl, runs the transfer and // controls data flow to/from the app. At the end of the transfer it issues a // burst terminate if not at the end of a burst and another command to this // bank is not available. sdrc_xfr_ctl #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_xfr_ctl ( .clk (clk ), .reset_n (reset_n ), /* Transfer request from bank_ctl */ .r2x_idle (r2x_idle ), .b2x_idle (b2x_idle ), .b2x_req (b2x_req ), .b2x_start (b2x_start ), .b2x_last (b2x_last ), .b2x_wrap (b2x_wrap ), .b2x_id (b2x_id ), .b2x_ba (b2x_ba ), .b2x_addr (b2x_addr ), .b2x_len (b2x_len ), .b2x_cmd (b2x_cmd ), .x2b_ack (x2b_ack ), /* Status to bank_ctl, req_gen */ .b2x_tras_ok (b2x_tras_ok ), .x2b_refresh (x2b_refresh ), .x2b_pre_ok (x2b_pre_ok ), .x2b_act_ok (x2b_act_ok ), .x2b_rdok (x2b_rdok ), .x2b_wrok (x2b_wrok ), /* SDRAM I/O */ .sdr_cs_n (sdr_cs_n ), .sdr_cke (sdr_cke ), .sdr_ras_n (sdr_ras_n ), .sdr_cas_n (sdr_cas_n ), .sdr_we_n (sdr_we_n ), .sdr_dqm (sdr_dqm ), .sdr_ba (sdr_ba ), .sdr_addr (sdr_addr ), .sdr_din (pad_sdr_din2 ), .sdr_dout (sdr_dout_int ), .sdr_den_n (sdr_den_n_int ), /* Data Flow to the app */ .x2a_rdstart (x2a_rdstart ), .x2a_wrstart (x2a_wrstart ), .x2a_id (xfr_id ), .x2a_rdlast (x2a_rdlast ), .x2a_wrlast (x2a_wrlast ), .a2x_wrdt (a2x_wrdt ), .a2x_wren_n (a2x_wren_n ), .x2a_wrnext (x2a_wrnext ), .x2a_rddt (x2a_rddt ), .x2a_rdok (x2a_rdok ), .sdr_init_done (sdr_init_done ), /* SDRAM Parameters */ .sdram_enable (cfg_sdr_en ), .sdram_mode_reg (cfg_sdr_mode_reg ), /* current xfr bank */ .xfr_bank_sel (xfr_bank_sel ), /* SDRAM Timing */ .cas_latency (cfg_sdr_cas ), .trp_delay (cfg_sdr_trp_d ), .trcar_delay (cfg_sdr_trcar_d ), .twr_delay (cfg_sdr_twr_d ), .rfsh_time (cfg_sdr_rfsh ), .rfsh_rmax (cfg_sdr_rfmax ) ); /****************************************************************************/ // Instantiate sdr_bs_convert // This model handle the bus with transaltion from application layer to // 8/16/32 SDRAM Memory format // During Write Phase, this block split the data as per SDRAM Width // During Read Phase, This block does the re-packing based on SDRAM // Width //--------------------------------------------------------------------------- sdrc_bs_convert #(.SDR_DW(SDR_DW) , .SDR_BW(SDR_BW)) u_bs_convert ( .clk (clk ), .reset_n (reset_n ), .sdr_width (sdr_width ), /* Control Signal from xfr ctrl */ // Read Interface Inputs .x2a_rdstart (x2a_rdstart ), .x2a_rdlast (x2a_rdlast ), .x2a_rdok (x2a_rdok ), // Read Interface outputs .x2a_rddt (x2a_rddt ), // Write Interface, Inputs .x2a_wrstart (x2a_wrstart ), .x2a_wrlast (x2a_wrlast ), .x2a_wrnext (x2a_wrnext ), // Write Interface, Outputs .a2x_wrdt (a2x_wrdt ), .a2x_wren_n (a2x_wren_n ), /* Control Signal from sdrc_bank_ctl */ /* Control Signal from/to to application i/f */ .app_wr_data (app_wr_data ), .app_wr_en_n (app_wr_en_n ), .app_wr_next (app_wr_next_req ), .app_last_wr (app_last_wr ), .app_rd_data (app_rd_data ), .app_rd_valid (app_rd_valid ), .app_last_rd (app_last_rd ) ); endmodule // sdrc_core
Go to most recent revision | Compare with Previous | Blame | View Log