URL
https://opencores.org/ocsvn/spi_master_slave/spi_master_slave/trunk
Subversion Repositories spi_master_slave
[/] [spi_master_slave/] [trunk/] [syn/] [spi_master.vhd] - Rev 23
Compare with Previous | Blame | View Log
----------------------------------------------------------------------------------------------------------------------- -- Author: Jonny Doin, jdoin@opencores.org, jonnydoin@gmail.com -- -- Create Date: 12:18:12 04/25/2011 -- Module Name: SPI_MASTER - RTL -- Project Name: SPI MASTER / SLAVE INTERFACE -- Target Devices: Spartan-6 -- Tool versions: ISE 13.1 -- Description: -- -- This block is the SPI master interface, implemented in one single entity. -- All internal core operations are synchronous to the 'sclk_i', and a spi base clock is generated by dividing sclk_i downto -- a frequency that is 2x the spi SCK line frequency. The divider value is passed as a generic parameter during instantiation. -- All parallel i/o interface operations are synchronous to the 'pclk_i' high speed clock, that can be asynchronous to the serial -- 'sclk_i' clock. -- For optimized use of longlines, connect 'sclk_i' and 'pclk_i' to the same global clock line. -- Fully pipelined cross-clock circuitry guarantees that no setup artifacts occur on the buffers that are accessed by the two -- clock domains. -- The block is very simple to use, and has parallel inputs and outputs that behave like a synchronous memory i/o. -- It is parameterizable via generics for the data width ('N'), SPI mode (CPHA and CPOL), lookahead prefetch signaling -- ('PREFETCH'), and spi base clock division from sclk_i ('SPI_2X_CLK_DIV'). -- -- SPI CLOCK GENERATION -- ==================== -- -- The clock generation for the SPI SCK is derived from the high-speed 'sclk_i' clock. The core divides this reference -- clock to form the SPI base clock, by the 'SPI_2X_CLK_DIV' generic parameter. The user must set the divider value for the -- SPI_2X clock, which is 2x the desired SCK frequency. -- All registers in the core are clocked by the high-speed clocks, and clock enables are used to run the FSM and other logic -- at lower rates. This architecture preserves FPGA clock resources like global clock buffers, and avoids path delays caused -- by combinatorial clock dividers outputs. -- The core has async clock domain circuitry to handle asynchronous clocks for the SPI and parallel interfaces. -- -- PARALLEL WRITE INTERFACE -- ======================== -- The parallel interface has an input port 'di_i' and an output port 'do_o'. -- Parallel load is controlled using 3 signals: 'di_i', 'di_req_o' and 'wren_i'. 'di_req_o' is a look ahead data request line, -- that is set 'PREFETCH' clock cycles in advance to synchronize a pipelined memory or fifo to present the -- next input data at 'di_i' in time to have continuous clock at the spi bus, to allow back-to-back continuous load. -- For a pipelined sync RAM, a PREFETCH of 2 cycles allows an address generator to present the new adress to the RAM in one -- cycle, and the RAM to respond in one more cycle, in time for 'di_i' to be latched by the shifter. -- If the user sequencer needs a different value for PREFETCH, the generic can be altered at instantiation time. -- The 'wren_i' write enable strobe must be valid at least one setup time before the rising edge of the last SPI clock cycle, -- if continuous transmission is intended. If 'wren_i' is not valid 2 SPI clock cycles after the last transmitted bit, the interface -- enters idle state and deasserts SSEL. -- When the interface is idle, 'wren_i' write strobe loads the data and starts transmission. 'di_req_o' will strobe when entering -- idle state, if a previously loaded data has already been transferred. -- -- PARALLEL WRITE SEQUENCE -- ======================= -- __ __ __ __ __ __ __ -- pclk_i __/ \__/ \__/ \__/ \__/ \__/ \__/ \... -- parallel interface clock -- ___________ -- di_req_o ________/ \_____________________... -- 'di_req_o' asserted on rising edge of 'pclk_i' -- ______________ ___________________________... -- di_i __old_data____X______new_data_____________... -- user circuit loads data on 'di_i' at next 'pclk_i' rising edge -- _______ -- wren_i __________________________/ \_______... -- user strobes 'wren_i' for one cycle of 'pclk_i' -- -- -- PARALLEL READ INTERFACE -- ======================= -- An internal buffer is used to copy the internal shift register data to drive the 'do_o' port. When a complete word is received, -- the core shift register is transferred to the buffer, at the rising edge of the spi clock, 'spi_clk'. -- The signal 'do_valid_o' is set one 'spi_clk' clock after, to directly drive a synchronous memory or fifo write enable. -- 'do_valid_o' is synchronous to the parallel interface clock, and changes only on rising edges of 'pclk_i'. -- When the interface is idle, data at the 'do_o' port holds the last word received. -- -- PARALLEL READ SEQUENCE -- ====================== -- ______ ______ ______ ______ -- spi_clk bit1 \______/ bitN \______/bitN-1\______/bitN-2\__... -- internal spi 2x base clock -- _ __ __ __ __ __ __ __ __ -- pclk_i \__/ \__/ \__/ \__/ \__/ \__/ \__/ \__/ \_... -- parallel interface clock (may be async to sclk_i) -- _____________ _____________________________________... -- 1) rx data is transferred to 'do_buffer_reg' -- do_o ___old_data__X__________new_data___________________... -- after last rx bit, at rising 'spi_clk'. -- ____________ -- do_valid_o ____________________________/ \_________... -- 2) 'do_valid_o' strobed for 2 'pclk_i' cycles -- -- on the 3rd 'pclk_i' rising edge. -- -- -- The propagation delay of spi_sck_o and spi_mosi_o, referred to the internal clock, is balanced by similar path delays, -- but the sampling delay of spi_miso_i imposes a setup time referred to the sck signal that limits the high frequency -- of the interface, for full duplex operation. -- -- This design was originally targeted to a Spartan-6 platform, synthesized with XST and normal constraints. -- The VHDL dialect used is VHDL'93, accepted largely by all synthesis tools. -- ------------------------------ COPYRIGHT NOTICE ----------------------------------------------------------------------- -- -- This file is part of the SPI MASTER/SLAVE INTERFACE project http://opencores.org/project,spi_master_slave -- -- Author(s): Jonny Doin, jdoin@opencores.org, jonnydoin@gmail.com -- -- Copyright (C) 2011 Jonny Doin -- ----------------------------- -- -- This source file may be used and distributed without restriction provided that this copyright statement is not -- removed from the file and that any derivative work contains the original copyright notice and the associated -- disclaimer. -- -- This source file is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser -- General Public License as published by the Free Software Foundation; either version 2.1 of the License, or -- (at your option) any later version. -- -- This source is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied -- warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more -- details. -- -- You should have received a copy of the GNU Lesser General Public License along with this source; if not, download -- it from http://www.gnu.org/licenses/lgpl.txt -- ------------------------------ REVISION HISTORY ----------------------------------------------------------------------- -- -- 2011/04/28 v0.01.0010 [JD] shifter implemented as a sequential process. timing problems and async issues in synthesis. -- 2011/05/01 v0.01.0030 [JD] changed original shifter design to a fully pipelined RTL fsmd. solved all synthesis issues. -- 2011/05/05 v0.01.0034 [JD] added an internal buffer register for rx_data, to allow greater liberty in data load/store. -- 2011/05/08 v0.10.0038 [JD] increased one state to have SSEL start one cycle before SCK. Implemented full CPOL/CPHA -- logic, based on generics, and do_valid_o signal. -- 2011/05/13 v0.20.0045 [JD] streamlined signal names, added PREFETCH parameter, added assertions. -- 2011/05/17 v0.80.0049 [JD] added explicit clock synchronization circuitry across clock boundaries. -- 2011/05/18 v0.95.0050 [JD] clock generation circuitry, with generators for all-rising-edge clock core. -- 2011/06/05 v0.96.0053 [JD] changed async clear to sync resets. -- 2011/06/07 v0.97.0065 [JD] added cross-clock buffers, fixed fsm async glitches. -- 2011/06/09 v0.97.0068 [JD] reduced control sets (resets, CE, presets) to the absolute minimum to operate, to reduce -- synthesis LUT overhead in Spartan-6 architecture. -- 2011/06/11 v0.97.0075 [JD] redesigned all parallel data interfacing ports, and implemented cross-clock strobe logic. -- 2011/06/12 v0.97.0079 [JD] streamlined wr_ack for all cases and eliminated unnecessary register resets. -- 2011/06/14 v0.97.0083 [JD] (bug CPHA effect) : redesigned SCK output circuit. -- (minor bug) : removed fsm registers from (not rst_i) chip enable. -- 2011/06/15 v0.97.0086 [JD] removed master MISO input register, to relax MISO data setup time (to get higher speed). -- 2011/07/09 v1.00.0095 [JD] changed all clocking scheme to use a single high-speed clock with clock enables to control lower -- frequency sequential circuits, to preserve clocking resources and avoid path delay glitches. -- 2011/07/10 v1.00.0098 [JD] implemented SCK clock divider circuit to generate spi clock directly from system clock. -- 2011/07/10 v1.10.0075 [JD] verified spi_master_slave in silicon at 50MHz, 25MHz, 16.666MHz, 12.5MHz, 10MHz, 8.333MHz, -- 7.1428MHz, 6.25MHz, 1MHz and 500kHz. The core proved very robust at all tested frequencies. -- 2011/07/16 v1.11.0080 [JD] verified both spi_master and spi_slave in loopback at 50MHz SPI clock. -- 2011/07/17 v1.11.0080 [JD] BUG: CPOL='1', CPHA='1' @50MHz causes MOSI to be shifted one bit earlier. -- BUG: CPOL='0', CPHA='1' causes SCK to have one extra pulse with one sclk_i width at the end. -- 2011/07/18 v1.12.0105 [JD] CHG: spi sck output register changed to remove glitch at last clock when CPHA='1'. -- for CPHA='1', max spi clock is 25MHz. for CPHA= '0', max spi clock is >50MHz. -- 2011/07/24 v1.13.0125 [JD] FIX: 'sck_ena_ce' is on half-cycle advanced to 'fsm_ce', elliminating CPHA='1' glitches. -- Core verified for all CPOL, CPHA at up to 50MHz, simulates to over 100MHz. -- 2011/07/29 v1.14.0130 [JD] Removed global signal setting at the FSM, implementing exhaustive explicit signal attributions -- for each state, to avoid reported inference problems in some synthesis engines. -- Streamlined port names and indentation blocks. -- 2011/08/01 v1.15.0135 [JD] Fixed latch inference for spi_mosi_o driver at the fsm. -- The master and slave cores were verified in FPGA with continuous transmission, for all SPI modes. -- 2011/08/04 v1.15.0136 [JD] Fixed assertions (PREFETCH >= 1) and minor comment bugs. -- ----------------------------------------------------------------------------------------------------------------------- -- TODO -- ==== -- ----------------------------------------------------------------------------------------------------------------------- library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; use ieee.std_logic_unsigned.all; --================================================================================================================ -- SYNTHESIS CONSIDERATIONS -- ======================== -- There are several output ports that are used to simulate and verify the core operation. -- Do not map any signals to the unused ports, and the synthesis tool will remove the related interfacing -- circuitry. -- The same is valid for the transmit and receive ports. If the receive ports are not mapped, the -- synthesis tool will remove the receive logic from the generated circuitry. -- Alternatively, you can remove these ports and related circuitry once the core is verified and -- integrated to your circuit. --================================================================================================================ entity spi_master is Generic ( N : positive := 32; -- 32bit serial word length is default CPOL : std_logic := '0'; -- SPI mode selection (mode 0 default) CPHA : std_logic := '0'; -- CPOL = clock polarity, CPHA = clock phase. PREFETCH : positive := 2; -- prefetch lookahead cycles SPI_2X_CLK_DIV : positive := 5); -- for a 100MHz sclk_i, yields a 10MHz SCK Port ( sclk_i : in std_logic := 'X'; -- high-speed serial interface system clock pclk_i : in std_logic := 'X'; -- high-speed parallel interface system clock rst_i : in std_logic := 'X'; -- reset core ---- serial interface ---- spi_ssel_o : out std_logic; -- spi bus slave select line spi_sck_o : out std_logic; -- spi bus sck spi_mosi_o : out std_logic; -- spi bus mosi output spi_miso_i : in std_logic := 'X'; -- spi bus spi_miso_i input ---- parallel interface ---- di_req_o : out std_logic; -- preload lookahead data request line di_i : in std_logic_vector (N-1 downto 0) := (others => 'X'); -- parallel data in (clocked on rising spi_clk after last bit) wren_i : in std_logic := 'X'; -- user data write enable, starts transmission when interface is idle wr_ack_o : out std_logic; -- write acknowledge do_valid_o : out std_logic; -- do_o data valid signal, valid during one spi_clk rising edge. do_o : out std_logic_vector (N-1 downto 0); -- parallel output (clocked on rising spi_clk after last bit) --- debug ports: can be removed or left unconnected for the application circuit --- sck_ena_o : out std_logic; -- debug: internal sck enable signal sck_ena_ce_o : out std_logic; -- debug: internal sck clock enable signal do_transfer_o : out std_logic; -- debug: internal transfer driver wren_o : out std_logic; -- debug: internal state of the wren_i pulse stretcher rx_bit_reg_o : out std_logic; -- debug: internal rx bit state_dbg_o : out std_logic_vector (3 downto 0); -- debug: internal state register core_clk_o : out std_logic; core_n_clk_o : out std_logic; core_ce_o : out std_logic; core_n_ce_o : out std_logic; sh_reg_dbg_o : out std_logic_vector (N-1 downto 0) -- debug: internal shift register ); end spi_master; --================================================================================================================ -- this architecture is a pipelined register-transfer description. -- all signals are clocked at the rising edge of the system clock 'sclk_i'. --================================================================================================================ architecture rtl of spi_master is -- core clocks, generated from 'sclk_i': initialized at GSR to differential values signal core_clk : std_logic := '0'; -- continuous core clock, positive logic signal core_n_clk : std_logic := '1'; -- continuous core clock, negative logic signal core_ce : std_logic := '0'; -- core clock enable, positive logic signal core_n_ce : std_logic := '1'; -- core clock enable, negative logic -- spi bus clock, generated from the CPOL selected core clock polarity signal spi_2x_ce : std_logic := '1'; -- spi_2x clock enable signal spi_clk : std_logic := '0'; -- spi bus output clock signal spi_clk_reg : std_logic; -- output pipeline delay for spi sck (do NOT global initialize) -- core fsm clock enables signal fsm_ce : std_logic := '1'; -- fsm clock enable signal sck_ena_ce : std_logic := '1'; -- SCK clock enable signal samp_ce : std_logic := '1'; -- data sampling clock enable -- -- GLOBAL RESET: -- all signals are initialized to zero at GSR (global set/reset) by giving explicit -- initialization values at declaration. This is needed for all Xilinx FPGAs, and -- especially for the Spartan-6 and newer CLB architectures, where a async reset can -- reduce the usability of the slice registers, due to the need to share the control -- set (RESET/PRESET, CLOCK ENABLE and CLOCK) by all 8 registers in a slice. -- By using GSR for the initialization, and reducing async RESET local init to the bare -- essential, the model achieves better LUT/FF packing and CLB usability. -- -- internal state signals for register and combinatorial stages signal state_next : natural range N+1 downto 0 := 0; signal state_reg : natural range N+1 downto 0 := 0; -- shifter signals for register and combinatorial stages signal sh_next : std_logic_vector (N-1 downto 0); signal sh_reg : std_logic_vector (N-1 downto 0); -- input bit sampled buffer signal rx_bit_reg : std_logic := '0'; -- buffered di_i data signals for register and combinatorial stages signal di_reg : std_logic_vector (N-1 downto 0); -- internal wren_i stretcher for fsm combinatorial stage signal wren : std_logic; signal wr_ack_next : std_logic := '0'; signal wr_ack_reg : std_logic := '0'; -- internal SSEL enable control signals signal ssel_ena_next : std_logic := '0'; signal ssel_ena_reg : std_logic := '0'; -- internal SCK enable control signals signal sck_ena_next : std_logic; signal sck_ena_reg : std_logic; -- buffered do_o data signals for register and combinatorial stages signal do_buffer_next : std_logic_vector (N-1 downto 0); signal do_buffer_reg : std_logic_vector (N-1 downto 0); -- internal signal to flag transfer to do_buffer_reg signal do_transfer_next : std_logic := '0'; signal do_transfer_reg : std_logic := '0'; -- internal input data request signal signal di_req_next : std_logic := '0'; signal di_req_reg : std_logic := '0'; -- cross-clock do_transfer_reg -> do_valid_o_reg pipeline signal do_valid_A : std_logic := '0'; signal do_valid_B : std_logic := '0'; signal do_valid_C : std_logic := '0'; signal do_valid_D : std_logic := '0'; signal do_valid_next : std_logic := '0'; signal do_valid_o_reg : std_logic := '0'; -- cross-clock di_req_reg -> di_req_o_reg pipeline signal di_req_o_A : std_logic := '0'; signal di_req_o_B : std_logic := '0'; signal di_req_o_C : std_logic := '0'; signal di_req_o_D : std_logic := '0'; signal di_req_o_next : std_logic := '1'; signal di_req_o_reg : std_logic := '1'; begin --============================================================================================= -- GENERICS CONSTRAINTS CHECKING --============================================================================================= -- minimum word width is 8 bits assert N >= 8 report "Generic parameter 'N' (shift register size) needs to be 8 bits minimum" severity FAILURE; -- minimum prefetch lookahead check assert PREFETCH >= 1 report "Generic parameter 'PREFETCH' (lookahead count) needs to be 1 minimum" severity FAILURE; -- maximum prefetch lookahead check assert PREFETCH <= N-5 report "Generic parameter 'PREFETCH' (lookahead count) out of range, needs to be N-5 maximum" severity FAILURE; -- SPI_2X_CLK_DIV clock divider value must not be zero assert SPI_2X_CLK_DIV > 0 report "Generic parameter 'SPI_2X_CLK_DIV' must not be zero" severity FAILURE; --============================================================================================= -- CLOCK GENERATION --============================================================================================= -- In order to preserve global clocking resources, the core clocking scheme is completely based -- on using clock enables to process the serial high-speed clock at lower rates for the core fsm, -- the spi clock generator and the input sampling clock. -- The clock generation block derives 2 continuous antiphase signals from the 2x spi base clock -- for the core clocking. -- The 2 clock phases are generated by separate and synchronous FFs, and should have only -- differential interconnect delay skew. -- Clock enable signals are generated with the same phase as the 2 core clocks, and these clock -- enables are used to control clocking of all internal synchronous circuitry. -- The clock enable phase is selected for serial input sampling, fsm clocking, and spi SCK output, -- based on the configuration of CPOL and CPHA. -- Each phase is selected so that all the registers can be clocked with a rising edge on all SPI -- modes, by a single high-speed global clock, preserving clock resources and clock to data skew. ----------------------------------------------------------------------------------------------- -- generate the 2x spi base clock enable from the serial high-speed input clock spi_2x_ce_gen_proc: process (sclk_i) is variable clk_cnt : integer range SPI_2X_CLK_DIV-1 downto 0 := 0; begin if sclk_i'event and sclk_i = '1' then if clk_cnt = SPI_2X_CLK_DIV-1 then spi_2x_ce <= '1'; clk_cnt := 0; else spi_2x_ce <= '0'; clk_cnt := clk_cnt + 1; end if; end if; end process spi_2x_ce_gen_proc; ----------------------------------------------------------------------------------------------- -- generate the core antiphase clocks and clock enables from the 2x base CE. core_clock_gen_proc : process (sclk_i) is begin if sclk_i'event and sclk_i = '1' then if spi_2x_ce = '1' then -- generate the 2 antiphase core clocks core_clk <= core_n_clk; core_n_clk <= not core_n_clk; -- generate the 2 phase core clock enables core_ce <= core_n_clk; core_n_ce <= not core_n_clk; else core_ce <= '0'; core_n_ce <= '0'; end if; end if; end process core_clock_gen_proc; --============================================================================================= -- GENERATE BLOCKS --============================================================================================= -- spi clk generator: generate spi_clk from core_clk depending on CPOL spi_sck_cpol_0_proc: if CPOL = '0' generate begin spi_clk <= core_clk; -- for CPOL=0, spi clk has idle LOW end generate; spi_sck_cpol_1_proc: if CPOL = '1' generate begin spi_clk <= core_n_clk; -- for CPOL=1, spi clk has idle HIGH end generate; ----------------------------------------------------------------------------------------------- -- Sampling clock enable generation: generate 'samp_ce' from 'core_ce' or 'core_n_ce' depending on CPHA -- always sample data at the half-cycle of the fsm update cell samp_ce_cpha_0_proc: if CPHA = '0' generate begin samp_ce <= core_ce; end generate; samp_ce_cpha_1_proc: if CPHA = '1' generate begin samp_ce <= core_n_ce; end generate; ----------------------------------------------------------------------------------------------- -- FSM clock enable generation: generate 'fsm_ce' from core_ce or core_n_ce depending on CPHA fsm_ce_cpha_0_proc: if CPHA = '0' generate begin fsm_ce <= core_n_ce; -- for CPHA=0, latch registers at rising edge of negative core clock enable end generate; fsm_ce_cpha_1_proc: if CPHA = '1' generate begin fsm_ce <= core_ce; -- for CPHA=1, latch registers at rising edge of positive core clock enable end generate; ----------------------------------------------------------------------------------------------- -- sck enable control: control sck advance phase for CPHA='1' relative to fsm clock sck_ena_ce <= core_n_ce; -- for CPHA=1, SCK is advanced one-half cycle --============================================================================================= -- REGISTERED INPUTS --============================================================================================= -- rx bit flop: capture rx bit after SAMPLE edge of sck rx_bit_proc : process (sclk_i, spi_miso_i) is begin if sclk_i'event and sclk_i = '1' then if samp_ce = '1' then rx_bit_reg <= spi_miso_i; end if; end if; end process rx_bit_proc; --============================================================================================= -- CROSS-CLOCK PIPELINE TRANSFER LOGIC --============================================================================================= -- do_valid_o and di_req_o strobe output logic -- this is a delayed pulse generator with a ripple-transfer FFD pipeline, that generates a -- fixed-length delayed pulse for the output flags, at the parallel clock domain out_transfer_proc : process ( pclk_i, do_transfer_reg, di_req_reg, do_valid_A, do_valid_B, do_valid_D, di_req_o_A, di_req_o_B, di_req_o_D ) is begin if pclk_i'event and pclk_i = '1' then -- clock at parallel port clock -- do_transfer_reg -> do_valid_o_reg do_valid_A <= do_transfer_reg; -- the input signal must be at least 2 clocks long do_valid_B <= do_valid_A; -- feed it to a ripple chain of FFDs do_valid_C <= do_valid_B; do_valid_D <= do_valid_C; do_valid_o_reg <= do_valid_next; -- registered output pulse -------------------------------- -- di_req_reg -> di_req_o_reg di_req_o_A <= di_req_reg; -- the input signal must be at least 2 clocks long di_req_o_B <= di_req_o_A; -- feed it to a ripple chain of FFDs di_req_o_C <= di_req_o_B; di_req_o_D <= di_req_o_C; di_req_o_reg <= di_req_o_next; -- registered output pulse end if; -- generate a 2-clocks pulse at the 3rd clock cycle do_valid_next <= do_valid_A and do_valid_B and not do_valid_D; di_req_o_next <= di_req_o_A and di_req_o_B and not di_req_o_D; end process out_transfer_proc; -- parallel load input registers: data register and write enable in_transfer_proc: process ( pclk_i, wren_i, wr_ack_reg ) is begin -- registered data input, input register with clock enable if pclk_i'event and pclk_i = '1' then if wren_i = '1' then di_reg <= di_i; -- parallel data input buffer register end if; end if; -- stretch wren pulse to be detected by spi fsm (ffd with sync preset and sync reset) if pclk_i'event and pclk_i = '1' then if wren_i = '1' then -- wren_i is the sync preset for wren wren <= '1'; elsif wr_ack_reg = '1' then -- wr_ack is the sync reset for wren wren <= '0'; end if; end if; end process in_transfer_proc; --============================================================================================= -- REGISTER TRANSFER PROCESSES --============================================================================================= -- fsm state and data registers: synchronous to the spi base reference clock core_reg_proc : process (sclk_i) is begin -- FF registers clocked on rising edge and cleared on sync rst_i if sclk_i'event and sclk_i = '1' then if rst_i = '1' then -- sync reset state_reg <= 0; -- only provide local reset for the state machine elsif fsm_ce = '1' then -- fsm_ce is clock enable for the fsm state_reg <= state_next; -- state register end if; end if; -- FF registers clocked synchronous to the fsm state if sclk_i'event and sclk_i = '1' then if fsm_ce = '1' then sh_reg <= sh_next; -- shift register ssel_ena_reg <= ssel_ena_next; -- spi select enable do_buffer_reg <= do_buffer_next; -- registered output data buffer do_transfer_reg <= do_transfer_next; -- output data transferred to buffer di_req_reg <= di_req_next; -- input data request wr_ack_reg <= wr_ack_next; -- write acknowledge for data load synchronization end if; end if; -- FF registers clocked one-half cycle earlier than the fsm state if sclk_i'event and sclk_i = '1' then if sck_ena_ce = '1' then sck_ena_reg <= sck_ena_next; -- spi clock enable: look ahead logic end if; end if; end process core_reg_proc; --============================================================================================= -- COMBINATORIAL LOGIC PROCESSES --============================================================================================= -- state and datapath combinatorial logic core_combi_proc : process ( sh_reg, state_reg, rx_bit_reg, ssel_ena_reg, sck_ena_reg, do_buffer_reg, do_transfer_reg, wr_ack_reg, di_req_reg, di_reg, wren ) is begin sh_next <= sh_reg; -- all output signals are assigned to (avoid latches) ssel_ena_next <= ssel_ena_reg; -- controls the slave select line sck_ena_next <= sck_ena_reg; -- controls the clock enable of spi sck line do_buffer_next <= do_buffer_reg; -- output data buffer do_transfer_next <= do_transfer_reg; -- output data flag wr_ack_next <= wr_ack_reg; -- write acknowledge di_req_next <= di_req_reg; -- prefetch data request spi_mosi_o <= sh_reg(N-1); -- default to avoid latch inference state_next <= state_reg; -- next state case state_reg is when (N+1) => -- this state is to enable SSEL before SCK spi_mosi_o <= sh_reg(N-1); -- shift out tx bit from the MSb ssel_ena_next <= '1'; -- tx in progress: will assert SSEL sck_ena_next <= '1'; -- enable SCK on next cycle (stays off on first SSEL clock cycle) di_req_next <= '0'; -- prefetch data request: deassert when shifting data wr_ack_next <= '0'; -- remove write acknowledge for all but the load stages state_next <= state_reg - 1; -- update next state at each sck pulse when (N) => -- deassert 'di_rdy' and stretch do_valid spi_mosi_o <= sh_reg(N-1); -- shift out tx bit from the MSb di_req_next <= '0'; -- prefetch data request: deassert when shifting data sh_next(N-1 downto 1) <= sh_reg(N-2 downto 0); -- shift inner bits sh_next(0) <= rx_bit_reg; -- shift in rx bit into LSb wr_ack_next <= '0'; -- remove write acknowledge for all but the load stages state_next <= state_reg - 1; -- update next state at each sck pulse when (N-1) downto (PREFETCH+3) => -- remove 'do_transfer' and shift bits spi_mosi_o <= sh_reg(N-1); -- shift out tx bit from the MSb di_req_next <= '0'; -- prefetch data request: deassert when shifting data do_transfer_next <= '0'; -- reset 'do_valid' transfer signal sh_next(N-1 downto 1) <= sh_reg(N-2 downto 0); -- shift inner bits sh_next(0) <= rx_bit_reg; -- shift in rx bit into LSb wr_ack_next <= '0'; -- remove write acknowledge for all but the load stages state_next <= state_reg - 1; -- update next state at each sck pulse when (PREFETCH+2) downto 2 => -- raise prefetch 'di_req_o' signal spi_mosi_o <= sh_reg(N-1); -- shift out tx bit from the MSb di_req_next <= '1'; -- request data in advance to allow for pipeline delays sh_next(N-1 downto 1) <= sh_reg(N-2 downto 0); -- shift inner bits sh_next(0) <= rx_bit_reg; -- shift in rx bit into LSb wr_ack_next <= '0'; -- remove write acknowledge for all but the load stages state_next <= state_reg - 1; -- update next state at each sck pulse when 1 => -- transfer rx data to do_buffer and restart if new data is written spi_mosi_o <= sh_reg(N-1); -- shift out tx bit from the MSb di_req_next <= '1'; -- request data in advance to allow for pipeline delays do_buffer_next(N-1 downto 1) <= sh_reg(N-2 downto 0); -- shift rx data directly into rx buffer do_buffer_next(0) <= rx_bit_reg; -- shift last rx bit into rx buffer do_transfer_next <= '1'; -- signal transfer to do_buffer if wren = '1' then -- load tx register if valid data present at di_i state_next <= N; -- next state is top bit of new data sh_next <= di_reg; -- load parallel data from di_reg into shifter sck_ena_next <= '1'; -- SCK enabled wr_ack_next <= '1'; -- acknowledge data in transfer else sck_ena_next <= '0'; -- SCK disabled: tx empty, no data to send wr_ack_next <= '0'; -- remove write acknowledge for all but the load stages state_next <= state_reg - 1; -- update next state at each sck pulse end if; when 0 => -- idle state: start and end of transmission di_req_next <= '1'; -- will request data if shifter empty sck_ena_next <= '0'; -- SCK disabled: tx empty, no data to send if wren = '1' then -- load tx register if valid data present at di_i spi_mosi_o <= di_reg(N-1); -- special case: shift out first tx bit from the MSb (look ahead) ssel_ena_next <= '1'; -- enable interface SSEL state_next <= N+1; -- start from idle: let one cycle for SSEL settling sh_next <= di_reg; -- load bits from di_reg into shifter wr_ack_next <= '1'; -- acknowledge data in transfer else spi_mosi_o <= sh_reg(N-1); -- shift out tx bit from the MSb ssel_ena_next <= '0'; -- deassert SSEL: interface is idle wr_ack_next <= '0'; -- remove write acknowledge for all but the load stages state_next <= 0; -- when idle, keep this state end if; when others => state_next <= 0; -- state 0 is safe state end case; end process core_combi_proc; --============================================================================================= -- OUTPUT LOGIC PROCESSES --============================================================================================= -- data output processes spi_ssel_o_proc: spi_ssel_o <= not ssel_ena_reg; -- active-low slave select line do_o_proc: do_o <= do_buffer_reg; -- parallel data out do_valid_o_proc: do_valid_o <= do_valid_o_reg; -- data out valid di_req_o_proc: di_req_o <= di_req_o_reg; -- input data request for next cycle wr_ack_o_proc: wr_ack_o <= wr_ack_reg; -- write acknowledge ----------------------------------------------------------------------------------------------- -- SCK out logic: pipeline phase compensation for the SCK line ----------------------------------------------------------------------------------------------- -- This is a MUX with an output register. -- The register gives us a pipeline delay for the SCK line, pairing with the state machine moore -- output pipeline delay for the MOSI line, and thus enabling higher SCK frequency. spi_sck_o_gen_proc : process (sclk_i, sck_ena_reg, spi_clk, spi_clk_reg) is begin if sclk_i'event and sclk_i = '1' then if sck_ena_reg = '1' then spi_clk_reg <= spi_clk; -- copy the selected clock polarity else spi_clk_reg <= CPOL; -- when clock disabled, set to idle polarity end if; end if; spi_sck_o <= spi_clk_reg; -- connect register to output end process spi_sck_o_gen_proc; --============================================================================================= -- DEBUG LOGIC PROCESSES --============================================================================================= -- these signals are useful for verification, and can be deleted after debug. do_transfer_proc: do_transfer_o <= do_transfer_reg; state_dbg_proc: state_dbg_o <= std_logic_vector(to_unsigned(state_reg, 4)); rx_bit_reg_proc: rx_bit_reg_o <= rx_bit_reg; wren_o_proc: wren_o <= wren; sh_reg_dbg_proc: sh_reg_dbg_o <= sh_reg; core_clk_o_proc: core_clk_o <= core_clk; core_n_clk_o_proc: core_n_clk_o <= core_n_clk; core_ce_o_proc: core_ce_o <= core_ce; core_n_ce_o_proc: core_n_ce_o <= core_n_ce; sck_ena_o_proc: sck_ena_o <= sck_ena_reg; sck_ena_ce_o_proc: sck_ena_ce_o <= sck_ena_ce; end architecture rtl;