Subversion Repositories test_project

/*
 *    pata_radisys.c - Intel PATA/SATA controllers
 *
 *	(C) 2006 Red Hat <alan@redhat.com>
 *
 *    Some parts based on ata_piix.c by Jeff Garzik and others.
 *
 *    A PIIX relative, this device has a single ATA channel and no
 *    slave timings, SITRE or PPE. In that sense it is a close relative
 *    of the original PIIX. It does however support UDMA 33/66 per channel
 *    although no other modes/timings. Also lacking is 32bit I/O on the ATA
 *    port.
 */
 
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/ata.h>
 
#define DRV_NAME	"pata_radisys"
#define DRV_VERSION	"0.4.4"
 
/**
 *	radisys_set_piomode - Initialize host controller PATA PIO timings
 *	@ap: ATA port
 *	@adev: Device whose timings we are configuring
 *
 *	Set PIO mode for device, in host controller PCI config space.
 *
 *	LOCKING:
 *	None (inherited from caller).
 */
 
static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
	u16 idetm_data;
	int control = 0;
 
	/*
	 *	See Intel Document 298600-004 for the timing programing rules
	 *	for PIIX/ICH. Note that the early PIIX does not have the slave
	 *	timing port at 0x44. The Radisys is a relative of the PIIX
	 *	but not the same so be careful.
	 */
 
	static const	 /* ISP  RTC */
	u8 timings[][2]	= { { 0, 0 },	/* Check me */
			    { 0, 0 },
			    { 1, 1 },
			    { 2, 2 },
			    { 3, 3 }, };
 
	if (pio > 0)
		control |= 1;	/* TIME1 enable */
	if (ata_pio_need_iordy(adev))
		control |= 2;	/* IE IORDY */
 
	pci_read_config_word(dev, 0x40, &idetm_data);
 
	/* Enable IE and TIME as appropriate. Clear the other
	   drive timing bits */
	idetm_data &= 0xCCCC;
	idetm_data |= (control << (4 * adev->devno));
	idetm_data |= (timings[pio][0] << 12) |
			(timings[pio][1] << 8);
	pci_write_config_word(dev, 0x40, idetm_data);
 
	/* Track which port is configured */
	ap->private_data = adev;
}
 
/**
 *	radisys_set_dmamode - Initialize host controller PATA DMA timings
 *	@ap: Port whose timings we are configuring
 *	@adev: Device to program
 *	@isich: True if the device is an ICH and has IOCFG registers
 *
 *	Set MWDMA mode for device, in host controller PCI config space.
 *
 *	LOCKING:
 *	None (inherited from caller).
 */
 
static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
	u16 idetm_data;
	u8 udma_enable;
 
	static const	 /* ISP  RTC */
	u8 timings[][2]	= { { 0, 0 },
			    { 0, 0 },
			    { 1, 1 },
			    { 2, 2 },
			    { 3, 3 }, };
 
	/*
	 * MWDMA is driven by the PIO timings. We must also enable
	 * IORDY unconditionally.
	 */
 
	pci_read_config_word(dev, 0x40, &idetm_data);
	pci_read_config_byte(dev, 0x48, &udma_enable);
 
	if (adev->dma_mode < XFER_UDMA_0) {
		unsigned int mwdma	= adev->dma_mode - XFER_MW_DMA_0;
		const unsigned int needed_pio[3] = {
			XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
		};
		int pio = needed_pio[mwdma] - XFER_PIO_0;
		int control = 3;	/* IORDY|TIME0 */
 
		/* If the drive MWDMA is faster than it can do PIO then
		   we must force PIO0 for PIO cycles. */
 
		if (adev->pio_mode < needed_pio[mwdma])
			control = 1;
 
		/* Mask out the relevant control and timing bits we will load. Also
		   clear the other drive TIME register as a precaution */
 
		idetm_data &= 0xCCCC;
		idetm_data |= control << (4 * adev->devno);
		idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
 
		udma_enable &= ~(1 << adev->devno);
	} else {
		u8 udma_mode;
 
		/* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */
 
		pci_read_config_byte(dev, 0x4A, &udma_mode);
 
		if (adev->xfer_mode == XFER_UDMA_2)
			udma_mode &= ~ (1 << adev->devno);
		else /* UDMA 4 */
			udma_mode |= (1 << adev->devno);
 
		pci_write_config_byte(dev, 0x4A, udma_mode);
 
		udma_enable |= (1 << adev->devno);
	}
	pci_write_config_word(dev, 0x40, idetm_data);
	pci_write_config_byte(dev, 0x48, udma_enable);
 
	/* Track which port is configured */
	ap->private_data = adev;
}
 
/**
 *	radisys_qc_issue_prot	-	command issue
 *	@qc: command pending
 *
 *	Called when the libata layer is about to issue a command. We wrap
 *	this interface so that we can load the correct ATA timings if
 *	necessary. Our logic also clears TIME0/TIME1 for the other device so
 *	that, even if we get this wrong, cycles to the other device will
 *	be made PIO0.
 */
 
static unsigned int radisys_qc_issue_prot(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	struct ata_device *adev = qc->dev;
 
	if (adev != ap->private_data) {
		/* UDMA timing is not shared */
		if (adev->dma_mode < XFER_UDMA_0) {
			if (adev->dma_mode)
				radisys_set_dmamode(ap, adev);
			else if (adev->pio_mode)
				radisys_set_piomode(ap, adev);
		}
	}
	return ata_qc_issue_prot(qc);
}
 
 
static struct scsi_host_template radisys_sht = {
	.module			= THIS_MODULE,
	.name			= DRV_NAME,
	.ioctl			= ata_scsi_ioctl,
	.queuecommand		= ata_scsi_queuecmd,
	.can_queue		= ATA_DEF_QUEUE,
	.this_id		= ATA_SHT_THIS_ID,
	.sg_tablesize		= LIBATA_MAX_PRD,
	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
	.emulated		= ATA_SHT_EMULATED,
	.use_clustering		= ATA_SHT_USE_CLUSTERING,
	.proc_name		= DRV_NAME,
	.dma_boundary		= ATA_DMA_BOUNDARY,
	.slave_configure	= ata_scsi_slave_config,
	.slave_destroy		= ata_scsi_slave_destroy,
	.bios_param		= ata_std_bios_param,
};
 
static const struct ata_port_operations radisys_pata_ops = {
	.set_piomode		= radisys_set_piomode,
	.set_dmamode		= radisys_set_dmamode,
	.mode_filter		= ata_pci_default_filter,
 
	.tf_load		= ata_tf_load,
	.tf_read		= ata_tf_read,
	.check_status		= ata_check_status,
	.exec_command		= ata_exec_command,
	.dev_select		= ata_std_dev_select,
 
	.freeze			= ata_bmdma_freeze,
	.thaw			= ata_bmdma_thaw,
	.error_handler		= ata_bmdma_error_handler,
	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
	.cable_detect		= ata_cable_unknown,
 
	.bmdma_setup		= ata_bmdma_setup,
	.bmdma_start		= ata_bmdma_start,
	.bmdma_stop		= ata_bmdma_stop,
	.bmdma_status		= ata_bmdma_status,
	.qc_prep		= ata_qc_prep,
	.qc_issue		= radisys_qc_issue_prot,
	.data_xfer		= ata_data_xfer,
 
	.irq_handler		= ata_interrupt,
	.irq_clear		= ata_bmdma_irq_clear,
	.irq_on			= ata_irq_on,
 
	.port_start		= ata_sff_port_start,
};
 
 
/**
 *	radisys_init_one - Register PIIX ATA PCI device with kernel services
 *	@pdev: PCI device to register
 *	@ent: Entry in radisys_pci_tbl matching with @pdev
 *
 *	Called from kernel PCI layer.  We probe for combined mode (sigh),
 *	and then hand over control to libata, for it to do the rest.
 *
 *	LOCKING:
 *	Inherited from PCI layer (may sleep).
 *
 *	RETURNS:
 *	Zero on success, or -ERRNO value.
 */
 
static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
	static int printed_version;
	static const struct ata_port_info info = {
		.sht		= &radisys_sht,
		.flags		= ATA_FLAG_SLAVE_POSS,
		.pio_mask	= 0x1f,	/* pio0-4 */
		.mwdma_mask	= 0x07, /* mwdma1-2 */
		.udma_mask	= 0x14, /* UDMA33/66 only */
		.port_ops	= &radisys_pata_ops,
	};
	const struct ata_port_info *ppi[] = { &info, NULL };
 
	if (!printed_version++)
		dev_printk(KERN_DEBUG, &pdev->dev,
			   "version " DRV_VERSION "\n");
 
	return ata_pci_init_one(pdev, ppi);
}
 
static const struct pci_device_id radisys_pci_tbl[] = {
	{ PCI_VDEVICE(RADISYS, 0x8201), },
 
	{ }	/* terminate list */
};
 
static struct pci_driver radisys_pci_driver = {
	.name			= DRV_NAME,
	.id_table		= radisys_pci_tbl,
	.probe			= radisys_init_one,
	.remove			= ata_pci_remove_one,
#ifdef CONFIG_PM
	.suspend		= ata_pci_device_suspend,
	.resume			= ata_pci_device_resume,
#endif
};
 
static int __init radisys_init(void)
{
	return pci_register_driver(&radisys_pci_driver);
}
 
static void __exit radisys_exit(void)
{
	pci_unregister_driver(&radisys_pci_driver);
}
 
module_init(radisys_init);
module_exit(radisys_exit);
 
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
MODULE_VERSION(DRV_VERSION);