Subversion Repositories test_project

#
# Multimedia Video device configuration
#

menuconfig RADIO_ADAPTERS
        bool "Radio Adapters"
        depends on VIDEO_DEV
        default y
        ---help---
          Say Y here to enable selecting AM/FM radio adapters.

if RADIO_ADAPTERS && VIDEO_DEV

config RADIO_CADET
        tristate "ADS Cadet AM/FM Tuner"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have one of these AM/FM radio cards, and then
          fill in the port address below.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          Further documentation on this driver can be found on the WWW at
          <http://linux.blackhawke.net/cadet/>.

          To compile this driver as a module, choose M here: the
          module will be called radio-cadet.

config RADIO_RTRACK
        tristate "AIMSlab RadioTrack (aka RadioReveal) support"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have one of these FM radio cards, and then fill
          in the port address below.

          Note that newer AIMSlab RadioTrack cards have a different chipset
          and are not supported by this driver.  For these cards, use the
          RadioTrack II driver below.

          If you have a GemTeks combined (PnP) sound- and radio card you must
          use this driver as a module and setup the card with isapnptools.
          You must also pass the module a suitable io parameter, 0x248 has
          been reported to be used by these cards.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>. More information is
          contained in the file
          <file:Documentation/video4linux/radiotrack.txt>.

          To compile this driver as a module, choose M here: the
          module will be called radio-aimslab.

config RADIO_RTRACK_PORT
        hex "RadioTrack i/o port (0x20f or 0x30f)"
        depends on RADIO_RTRACK=y
        default "20f"
        help
          Enter either 0x30f or 0x20f here.  The card default is 0x30f, if you
          haven't changed the jumper setting on the card.

config RADIO_RTRACK2
        tristate "AIMSlab RadioTrack II support"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have this FM radio card, and then fill in the
          port address below.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-rtrack2.

config RADIO_RTRACK2_PORT
        hex "RadioTrack II i/o port (0x20c or 0x30c)"
        depends on RADIO_RTRACK2=y
        default "30c"
        help
          Enter either 0x30c or 0x20c here.  The card default is 0x30c, if you
          haven't changed the jumper setting on the card.

config RADIO_AZTECH
        tristate "Aztech/Packard Bell Radio"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have one of these FM radio cards, and then fill
          in the port address below.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-aztech.

config RADIO_AZTECH_PORT
        hex "Aztech/Packard Bell I/O port (0x350 or 0x358)"
        depends on RADIO_AZTECH=y
        default "350"
        help
          Enter either 0x350 or 0x358 here.  The card default is 0x350, if you
          haven't changed the setting of jumper JP3 on the card.  Removing the
          jumper sets the card to 0x358.

config RADIO_GEMTEK
        tristate "GemTek Radio card (or compatible) support"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have this FM radio card, and then fill in the
          I/O port address and settings below. The following cards either have
          GemTek Radio tuner or are rebranded GemTek Radio cards:

          - Sound Vision 16 Gold with FM Radio
          - Typhoon Radio card (some models)
          - Hama Radio card

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-gemtek.

config RADIO_GEMTEK_PORT
        hex "Fixed I/O port (0x20c, 0x30c, 0x24c, 0x34c, 0c24c or 0x28c)"
        depends on RADIO_GEMTEK=y
        default "34c"
        help
          Enter either 0x20c, 0x30c, 0x24c or 0x34c here. The card default is
          0x34c, if you haven't changed the jumper setting on the card. On
          Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O
          port is 0x20c, 0x248 or 0x28c.
          If automatic I/O port probing is enabled this port will be used only
          in case of automatic probing failure, ie. as a fallback.

config RADIO_GEMTEK_PROBE
        bool "Automatic I/O port probing"
        depends on RADIO_GEMTEK=y
        default y
        help
          Say Y here to enable automatic probing for GemTek Radio card. The
          following ports will be probed: 0x20c, 0x30c, 0x24c, 0x34c, 0x248 and
          0x28c.

config RADIO_GEMTEK_PCI
        tristate "GemTek PCI Radio Card support"
        depends on VIDEO_V4L2 && PCI
        ---help---
          Choose Y here if you have this PCI FM radio card.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video for Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-gemtek-pci.

config RADIO_MAXIRADIO
        tristate "Guillemot MAXI Radio FM 2000 radio"
        depends on VIDEO_V4L2 && PCI
        ---help---
          Choose Y here if you have this radio card.  This card may also be
          found as Gemtek PCI FM.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-maxiradio.

config RADIO_MAESTRO
        tristate "Maestro on board radio"
        depends on VIDEO_V4L2 && PCI
        ---help---
          Say Y here to directly support the on-board radio tuner on the
          Maestro 2 or 2E sound card.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-maestro.

config RADIO_SF16FMI
        tristate "SF16FMI Radio"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have one of these FM radio cards.  If you
          compile the driver into the kernel and your card is not PnP one, you
          have to add "sf16fm=<io>" to the kernel command line (I/O address is
          0x284 or 0x384).

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-sf16fmi.

config RADIO_SF16FMR2
        tristate "SF16FMR2 Radio"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have one of these FM radio cards.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found on the WWW at
          <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.

          To compile this driver as a module, choose M here: the
          module will be called radio-sf16fmr2.

config RADIO_TERRATEC
        tristate "TerraTec ActiveRadio ISA Standalone"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have this FM radio card, and then fill in the
          port address below. (TODO)

          Note: This driver is in its early stages.  Right now volume and
          frequency control and muting works at least for me, but
          unfortunately I have not found anybody who wants to use this card
          with Linux.  So if it is this what YOU are trying to do right now,
          PLEASE DROP ME A NOTE!!  Rolf Offermanns <rolf@offermanns.de>.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-terratec.

config RADIO_TERRATEC_PORT
        hex "Terratec i/o port (normally 0x590)"
        depends on RADIO_TERRATEC=y
        default "590"
        help
          Fill in the I/O port of your TerraTec FM radio card. If unsure, go
          with the default.

config RADIO_TRUST
        tristate "Trust FM radio card"
        depends on ISA && VIDEO_V4L2
        help
          This is a driver for the Trust FM radio cards. Say Y if you have
          such a card and want to use it under Linux.

          To compile this driver as a module, choose M here: the
          module will be called radio-trust.

config RADIO_TRUST_PORT
        hex "Trust i/o port (usually 0x350 or 0x358)"
        depends on RADIO_TRUST=y
        default "350"
        help
          Enter the I/O port of your Trust FM radio card. If unsure, try the
          values "0x350" or "0x358".

config RADIO_TYPHOON
        tristate "Typhoon Radio (a.k.a. EcoRadio)"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have one of these FM radio cards, and then fill
          in the port address and the frequency used for muting below.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-typhoon.

config RADIO_TYPHOON_PROC_FS
        bool "Support for /proc/radio-typhoon"
        depends on PROC_FS && RADIO_TYPHOON
        help
          Say Y here if you want the typhoon radio card driver to write
          status information (frequency, volume, muted, mute frequency,
          base address) to /proc/radio-typhoon. The file can be viewed with
          your favorite pager (i.e. use "more /proc/radio-typhoon" or "less
          /proc/radio-typhoon" or simply "cat /proc/radio-typhoon").

config RADIO_TYPHOON_PORT
        hex "Typhoon I/O port (0x316 or 0x336)"
        depends on RADIO_TYPHOON=y
        default "316"
        help
          Enter the I/O port of your Typhoon or EcoRadio radio card.

config RADIO_TYPHOON_MUTEFREQ
        int "Typhoon frequency set when muting the device (kHz)"
        depends on RADIO_TYPHOON=y
        default "87500"
        help
          Enter the frequency used for muting the radio. The device is never
          completely silent. If the volume is just turned down, you can still
          hear silent voices and music. For that reason, the frequency of the
          radio device is set to the frequency you can enter here whenever
          the device is muted. There should be no local radio station at that
          frequency.

config RADIO_ZOLTRIX
        tristate "Zoltrix Radio"
        depends on ISA && VIDEO_V4L2
        ---help---
          Choose Y here if you have one of these FM radio cards, and then fill
          in the port address below.

          In order to control your radio card, you will need to use programs
          that are compatible with the Video For Linux API.  Information on
          this API and pointers to "v4l" programs may be found at
          <file:Documentation/video4linux/API.html>.

          To compile this driver as a module, choose M here: the
          module will be called radio-zoltrix.

config RADIO_ZOLTRIX_PORT
        hex "ZOLTRIX I/O port (0x20c or 0x30c)"
        depends on RADIO_ZOLTRIX=y
        default "20c"
        help
          Enter the I/O port of your Zoltrix radio card.

config USB_DSBR
        tristate "D-Link/GemTek USB FM radio support"
        depends on USB && VIDEO_V4L2
        ---help---
          Say Y here if you want to connect this type of radio to your
          computer's USB port. Note that the audio is not digital, and
          you must connect the line out connector to a sound card or a
          set of speakers.

          To compile this driver as a module, choose M here: the
          module will be called dsbr100.

endif # RADIO_ADAPTERS