OpenCores
URL https://opencores.org/ocsvn/test_project/test_project/trunk

Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [net/] [phy/] [Kconfig] - Rev 62

Compare with Previous | Blame | View Log

#
# PHY Layer Configuration
#

menuconfig PHYLIB
        tristate "PHY Device support and infrastructure"
        depends on !S390
        depends on NET_ETHERNET && (BROKEN || !S390)
        help
          Ethernet controllers are usually attached to PHY
          devices.  This option provides infrastructure for
          managing PHY devices.

if PHYLIB

comment "MII PHY device drivers"

config MARVELL_PHY
        tristate "Drivers for Marvell PHYs"
        ---help---
          Currently has a driver for the 88E1011S
        
config DAVICOM_PHY
        tristate "Drivers for Davicom PHYs"
        ---help---
          Currently supports dm9161e and dm9131

config QSEMI_PHY
        tristate "Drivers for Quality Semiconductor PHYs"
        ---help---
          Currently supports the qs6612

config LXT_PHY
        tristate "Drivers for the Intel LXT PHYs"
        ---help---
          Currently supports the lxt970, lxt971

config CICADA_PHY
        tristate "Drivers for the Cicada PHYs"
        ---help---
          Currently supports the cis8204

config VITESSE_PHY
        tristate "Drivers for the Vitesse PHYs"
        ---help---
          Currently supports the vsc8244

config SMSC_PHY
        tristate "Drivers for SMSC PHYs"
        ---help---
          Currently supports the LAN83C185 PHY

config BROADCOM_PHY
        tristate "Drivers for Broadcom PHYs"
        ---help---
          Currently supports the BCM5411, BCM5421 and BCM5461 PHYs.

config ICPLUS_PHY
        tristate "Drivers for ICPlus PHYs"
        ---help---
          Currently supports the IP175C PHY.

config FIXED_PHY
        tristate "Drivers for PHY emulation on fixed speed/link"
        ---help---
          Adds the driver to PHY layer to cover the boards that do not have any PHY bound,
          but with the ability to manipulate the speed/link in software. The relevant MII
          speed/duplex parameters could be effectively handled in a user-specified function.
          Currently tested with mpc866ads.

config FIXED_MII_10_FDX
        bool "Emulation for 10M Fdx fixed PHY behavior"
        depends on FIXED_PHY

config FIXED_MII_100_FDX
        bool "Emulation for 100M Fdx fixed PHY behavior"
        depends on FIXED_PHY

config FIXED_MII_1000_FDX
        bool "Emulation for 1000M Fdx fixed PHY behavior"
        depends on FIXED_PHY

config FIXED_MII_AMNT
        int "Number of emulated PHYs to allocate "
        depends on FIXED_PHY
        default "1"
        ---help---
        Sometimes it is required to have several independent emulated
        PHYs on the bus (in case of multi-eth but phy-less HW for instance).
        This control will have specified number allocated for each fixed
        PHY type enabled.

config MDIO_BITBANG
        tristate "Support for bitbanged MDIO buses"
        help
          This module implements the MDIO bus protocol in software,
          for use by low level drivers that export the ability to
          drive the relevant pins.

          If in doubt, say N.

endif # PHYLIB

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2025 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.