Subversion Repositories test_project

#
# Tulip family network device configuration
#

menuconfig NET_TULIP
        bool "\"Tulip\" family network device support"
        depends on PCI || EISA || CARDBUS
        help
          This selects the "Tulip" family of EISA/PCI network cards.

if NET_TULIP

config DE2104X
        tristate "Early DECchip Tulip (dc2104x) PCI support (EXPERIMENTAL)"
        depends on PCI && EXPERIMENTAL
        select CRC32
        ---help---
          This driver is developed for the SMC EtherPower series Ethernet
          cards and also works with cards based on the DECchip
          21040 (Tulip series) chips.  Some LinkSys PCI cards are
          of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
          (smc9332dst), you can also try the driver for "Generic DECchip"
          cards, below.  However, most people with a network card of this type
          will say Y here.) Do read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module will
          be called de2104x.

config TULIP
        tristate "DECchip Tulip (dc2114x) PCI support"
        depends on PCI
        select CRC32
        ---help---
          This driver is developed for the SMC EtherPower series Ethernet
          cards and also works with cards based on the DECchip 
          21140 (Tulip series) chips.  Some LinkSys PCI cards are
          of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
          (smc9332dst), you can also try the driver for "Generic DECchip"
          cards, above.  However, most people with a network card of this type
          will say Y here.) Do read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module will
          be called tulip.

config TULIP_MWI
        bool "New bus configuration (EXPERIMENTAL)"
        depends on TULIP && EXPERIMENTAL
        help
          This configures your Tulip card specifically for the card and
          system cache line size type you are using.

          This is experimental code, not yet tested on many boards.

          If unsure, say N.

config TULIP_MMIO
        bool "Use PCI shared mem for NIC registers"
        depends on TULIP
        help
          Use PCI shared memory for the NIC registers, rather than going through
          the Tulip's PIO (programmed I/O ports).  Faster, but could produce
          obscure bugs if your mainboard has memory controller timing issues.
          If in doubt, say N.

config TULIP_NAPI
        bool "Use RX polling (NAPI)"
        depends on TULIP
        help
          NAPI is a new driver API designed to reduce CPU and interrupt load
          when the driver is receiving lots of packets from the card. It is
          still somewhat experimental and thus not yet enabled by default.

          If your estimated Rx load is 10kpps or more, or if the card will be
          deployed on potentially unfriendly networks (e.g. in a firewall),
          then say Y here.

          If in doubt, say N.

config TULIP_NAPI_HW_MITIGATION
        bool "Use Interrupt Mitigation"
        depends on TULIP_NAPI
        ---help---
          Use HW to reduce RX interrupts. Not strictly necessary since NAPI
          reduces RX interrupts by itself. Interrupt mitigation reduces RX
          interrupts even at low levels of traffic at the cost of a small
          latency.

          If in doubt, say Y.

config DE4X5
        tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA"
        depends on PCI || EISA
        select CRC32
        ---help---
          This is support for the DIGITAL series of PCI/EISA Ethernet cards.
          These include the DE425, DE434, DE435, DE450 and DE500 models.  If
          you have a network card of this type, say Y and read the
          Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>. More specific
          information is contained in
          <file:Documentation/networking/de4x5.txt>.

          To compile this driver as a module, choose M here. The module will
          be called de4x5.

config WINBOND_840
        tristate "Winbond W89c840 Ethernet support"
        depends on PCI
        select CRC32
        select MII
        help
          This driver is for the Winbond W89c840 chip.  It also works with 
          the TX9882 chip on the Compex RL100-ATX board.
          More specific information and updates are available from
          <http://www.scyld.com/network/drivers.html>.

config DM9102
        tristate "Davicom DM910x/DM980x support"
        depends on PCI
        select CRC32
        ---help---
          This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
          Davicom (<http://www.davicom.com.tw/>).  If you have such a network
          (Ethernet) card, say Y.  Some information is contained in the file
          <file:Documentation/networking/dmfe.txt>.

          To compile this driver as a module, choose M here. The module will
          be called dmfe.

config ULI526X
        tristate "ULi M526x controller support"
        depends on PCI
        select CRC32
        ---help---
          This driver is for ULi M5261/M5263 10/100M Ethernet Controller
          (<http://www.uli.com.tw/>).

          To compile this driver as a module, choose M here. The module will
          be called uli526x.
          
config PCMCIA_XIRCOM
        tristate "Xircom CardBus support (new driver)"
        depends on CARDBUS
        ---help---
          This driver is for the Digital "Tulip" Ethernet CardBus adapters.
          It should work with most DEC 21*4*-based chips/ethercards, as well
          as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
          ASIX.

          To compile this driver as a module, choose M here. The module will
          be called xircom_cb.  If unsure, say N.

config PCMCIA_XIRTULIP
        tristate "Xircom Tulip-like CardBus support (old driver)"
        depends on CARDBUS && BROKEN_ON_SMP
        select CRC32
        ---help---
          This driver is for the Digital "Tulip" Ethernet CardBus adapters.
          It should work with most DEC 21*4*-based chips/ethercards, as well
          as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
          ASIX.

          To compile this driver as a module, choose M here. The module will
          be called xircom_tulip_cb.  If unsure, say N.

endif # NET_TULIP