URL
https://opencores.org/ocsvn/turbo8051/turbo8051/trunk
Subversion Repositories turbo8051
[/] [turbo8051/] [trunk/] [rtl/] [uart/] [uart_rxfsm.v] - Rev 58
Go to most recent revision | Compare with Previous | Blame | View Log
////////////////////////////////////////////////////////////////////// //// //// //// Tubo 8051 cores UART Interface Module //// //// //// //// This file is part of the Turbo 8051 cores project //// //// http://www.opencores.org/cores/turbo8051/ //// //// //// //// Description //// //// Turbo 8051 definitions. //// //// //// //// To Do: //// //// nothing //// //// //// //// Author(s): //// //// - Dinesh Annayya, dinesha@opencores.org //// //// //// ////////////////////////////////////////////////////////////////////// //// //// //// Copyright (C) 2000 Authors and OPENCORES.ORG //// //// //// //// This source file may be used and distributed without //// //// restriction provided that this copyright statement is not //// //// removed from the file and that any derivative work contains //// //// the original copyright notice and the associated disclaimer. //// //// //// //// This source file is free software; you can redistribute it //// //// and/or modify it under the terms of the GNU Lesser General //// //// Public License as published by the Free Software Foundation; //// //// either version 2.1 of the License, or (at your option) any //// //// later version. //// //// //// //// This source is distributed in the hope that it will be //// //// useful, but WITHOUT ANY WARRANTY; without even the implied //// //// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR //// //// PURPOSE. See the GNU Lesser General Public License for more //// //// details. //// //// //// //// You should have received a copy of the GNU Lesser General //// //// Public License along with this source; if not, download it //// //// from http://www.opencores.org/lgpl.shtml //// //// //// ////////////////////////////////////////////////////////////////////// // UART rx state machine module uart_rxfsm ( reset_n , baud_clk_16x , cfg_rx_enable , cfg_stop_bit , cfg_pri_mod , error_ind , // FIFO control signal fifo_aval , fifo_wr , fifo_data , // Line Interface si ); input reset_n ; // active low reset signal input baud_clk_16x ; // baud clock-16x input cfg_rx_enable ; // transmit interface enable input cfg_stop_bit ; // stop bit // 0 --> 1 stop, 1 --> 2 Stop input [1:0] cfg_pri_mod ;// Priority Mode // 2'b00 --> None // 2'b10 --> Even priority // 2'b11 --> Odd priority output [1:0] error_ind ; // 2'b00 --> Normal // 2'b01 --> framing error // 2'b10 --> parity error // 2'b11 --> fifo full //-------------------------------------- // FIFO control signal //-------------------------------------- input fifo_aval ; // fifo empty output fifo_wr ; // fifo write, assumed no back to back write output [7:0] fifo_data ; // fifo write data // Line Interface input si ; // rxd pin reg [7:0] fifo_data ; // fifo write data reg fifo_wr ; // fifo write reg [1:0] error_ind ; reg [2:0] cnt ; reg [3:0] offset ; // free-running counter from 0 - 15 reg [3:0] rxpos ; // stable rx position reg [2:0] rxstate ; parameter idle_st = 3'b000; parameter xfr_start = 3'b001; parameter xfr_data_st = 3'b010; parameter xfr_pri_st = 3'b011; parameter xfr_stop_st1 = 3'b100; parameter xfr_stop_st2 = 3'b101; always @(negedge reset_n or posedge baud_clk_16x) begin if(reset_n == 0) begin rxstate <= 3'b0; offset <= 4'b0; rxpos <= 4'b0; cnt <= 3'b0; error_ind <= 2'b0; fifo_wr <= 1'b0; fifo_data <= 8'h0; end else begin offset <= offset + 1; case(rxstate) idle_st : begin if(!si) begin // Start indication if(fifo_aval && cfg_rx_enable) begin rxstate <= xfr_start; cnt <= 0; rxpos <= offset + 8; // Assign center rxoffset error_ind <= 2'b00; end else begin error_ind <= 2'b11; // fifo full error indication end end else begin error_ind <= 2'b00; // Reset Error end end xfr_start : begin // Make Sure that minimum 8 cycle low is detected if(cnt < 7 && si) begin // Start indication rxstate <= idle_st; end else if(cnt == 7 && !si) begin // Start indication rxstate <= xfr_data_st; cnt <= 0; end else begin cnt <= cnt +1; end end xfr_data_st : begin if(rxpos == offset) begin fifo_data[cnt] <= si; cnt <= cnt+1; if(cnt == 7) begin fifo_wr <= 1; if(cfg_pri_mod == 2'b00) // No Priority rxstate <= xfr_stop_st1; else rxstate <= xfr_pri_st; end end end xfr_pri_st : begin fifo_wr <= 0; if(rxpos == offset) begin if(cfg_pri_mod == 2'b10) // even priority if( si != ^fifo_data) error_ind <= 2'b10; else // Odd Priority if( si != ~(^fifo_data)) error_ind <= 2'b10; rxstate <= xfr_stop_st1; end end xfr_stop_st1 : begin fifo_wr <= 0; if(rxpos == offset) begin if(si) begin if(cfg_stop_bit) // Two Stop bit rxstate <= xfr_stop_st2; else rxstate <= idle_st; end else begin // Framing error error_ind <= 2'b01; rxstate <= idle_st; end end end xfr_stop_st2 : begin if(rxpos == offset) begin if(si) begin rxstate <= idle_st; end else begin // Framing error error_ind <= 2'b01; rxstate <= idle_st; end end end endcase end end endmodule
Go to most recent revision | Compare with Previous | Blame | View Log