OpenCores
URL https://opencores.org/ocsvn/uart_block/uart_block/trunk

Subversion Repositories uart_block

[/] [uart_block/] [trunk/] [hdl/] [iseProject/] [serial_receiver.syr] - Rev 7

Go to most recent revision | Compare with Previous | Blame | View Log

Release 13.4 - xst O.87xd (nt64)
Copyright (c) 1995-2011 Xilinx, Inc.  All rights reserved.
--> Parameter TMPDIR set to xst/projnav.tmp


Total REAL time to Xst completion: 0.00 secs
Total CPU time to Xst completion: 0.05 secs
 
--> Parameter xsthdpdir set to xst


Total REAL time to Xst completion: 0.00 secs
Total CPU time to Xst completion: 0.05 secs
 
--> Reading design: serial_receiver.prj

TABLE OF CONTENTS
  1) Synthesis Options Summary
  2) HDL Compilation
  3) Design Hierarchy Analysis
  4) HDL Analysis
  5) HDL Synthesis
     5.1) HDL Synthesis Report
  6) Advanced HDL Synthesis
     6.1) Advanced HDL Synthesis Report
  7) Low Level Synthesis
  8) Partition Report
  9) Final Report
        9.1) Device utilization summary
        9.2) Partition Resource Summary
        9.3) TIMING REPORT


=========================================================================
*                      Synthesis Options Summary                        *
=========================================================================
---- Source Parameters
Input File Name                    : "serial_receiver.prj"
Input Format                       : mixed
Ignore Synthesis Constraint File   : NO

---- Target Parameters
Output File Name                   : "serial_receiver"
Output Format                      : NGC
Target Device                      : xc3s500e-4-fg320

---- Source Options
Top Module Name                    : serial_receiver
Automatic FSM Extraction           : YES
FSM Encoding Algorithm             : Auto
Safe Implementation                : No
FSM Style                          : LUT
RAM Extraction                     : Yes
RAM Style                          : Auto
ROM Extraction                     : Yes
Mux Style                          : Auto
Decoder Extraction                 : YES
Priority Encoder Extraction        : Yes
Shift Register Extraction          : YES
Logical Shifter Extraction         : YES
XOR Collapsing                     : YES
ROM Style                          : Auto
Mux Extraction                     : Yes
Resource Sharing                   : YES
Asynchronous To Synchronous        : NO
Multiplier Style                   : Auto
Automatic Register Balancing       : No

---- Target Options
Add IO Buffers                     : YES
Global Maximum Fanout              : 100000
Add Generic Clock Buffer(BUFG)     : 24
Register Duplication               : YES
Slice Packing                      : YES
Optimize Instantiated Primitives   : NO
Use Clock Enable                   : Yes
Use Synchronous Set                : Yes
Use Synchronous Reset              : Yes
Pack IO Registers into IOBs        : Auto
Equivalent register Removal        : YES

---- General Options
Optimization Goal                  : Speed
Optimization Effort                : 1
Keep Hierarchy                     : No
Netlist Hierarchy                  : As_Optimized
RTL Output                         : Yes
Global Optimization                : AllClockNets
Read Cores                         : YES
Write Timing Constraints           : NO
Cross Clock Analysis               : NO
Hierarchy Separator                : /
Bus Delimiter                      : <>
Case Specifier                     : Maintain
Slice Utilization Ratio            : 100
BRAM Utilization Ratio             : 100
Verilog 2001                       : YES
Auto BRAM Packing                  : NO
Slice Utilization Ratio Delta      : 5

=========================================================================


=========================================================================
*                          HDL Compilation                              *
=========================================================================
Compiling vhdl file "E:/uart_block/hdl/iseProject/pkgDefinitions.vhd" in Library work.
Architecture pkgdefinitions of Entity pkgdefinitions is up to date.
Compiling vhdl file "E:/uart_block/hdl/iseProject/serial_receiver.vhd" in Library work.
Entity <serial_receiver> compiled.
Entity <serial_receiver> (Architecture <behavioral>) compiled.

=========================================================================
*                     Design Hierarchy Analysis                         *
=========================================================================
Analyzing hierarchy for entity <serial_receiver> in library <work> (architecture <behavioral>).


=========================================================================
*                            HDL Analysis                               *
=========================================================================
Analyzing Entity <serial_receiver> in library <work> (Architecture <behavioral>).
WARNING:Xst:819 - "E:/uart_block/hdl/iseProject/serial_receiver.vhd" line 86: One or more signals are missing in the process sensitivity list. To enable synthesis of FPGA/CPLD hardware, XST will assume that all necessary signals are present in the sensitivity list. Please note that the result of the synthesis may differ from the initial design specification. The missing signals are:
   <serial_in>
Entity <serial_receiver> analyzed. Unit <serial_receiver> generated.


=========================================================================
*                           HDL Synthesis                               *
=========================================================================

Performing bidirectional port resolution...

Synthesizing Unit <serial_receiver>.
    Related source file is "E:/uart_block/hdl/iseProject/serial_receiver.vhd".
    Found finite state machine <FSM_0> for signal <current_s>.
    -----------------------------------------------------------------------
    | States             | 10                                             |
    | Transitions        | 10                                             |
    | Inputs             | 0                                              |
    | Outputs            | 10                                             |
    | Clock              | baudClk                   (rising_edge)        |
    | Reset              | syncDetected              (negative)           |
    | Reset type         | asynchronous                                   |
    | Reset State        | rx_idle                                        |
    | Power Up State     | rx_idle                                        |
    | Encoding           | automatic                                      |
    | Implementation     | LUT                                            |
    -----------------------------------------------------------------------
    Found finite state machine <FSM_1> for signal <filterRx>.
    -----------------------------------------------------------------------
    | States             | 4                                              |
    | Transitions        | 8                                              |
    | Inputs             | 2                                              |
    | Outputs            | 4                                              |
    | Clock              | baudOverSampleClk         (rising_edge)        |
    | Reset              | rst                       (positive)           |
    | Reset type         | asynchronous                                   |
    | Reset State        | s0                                             |
    | Power Up State     | s0                                             |
    | Encoding           | automatic                                      |
    | Implementation     | LUT                                            |
    -----------------------------------------------------------------------
WARNING:Xst:737 - Found 8-bit latch for signal <data_byte>. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<0>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<1>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<2>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<3>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<4>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<5>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<6>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtridata_byteReceived<7>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<0>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<1>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<2>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<3>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<4>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<5>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<6>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
WARNING:Xst:736 - Found 1-bit latch for signal <Mtrien_byteReceived<7>> created at line 92. Latches may be generated from incomplete case or if statements. We do not recommend the use of latches in FPGA/CPLD designs, as they may lead to timing problems.
INFO:Xst:2371 - HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
    Found 8-bit tristate buffer for signal <byteReceived>.
    Found 1-bit register for signal <syncDetected>.
    Summary:
        inferred   2 Finite State Machine(s).
        inferred   1 D-type flip-flop(s).
        inferred   8 Tristate(s).
Unit <serial_receiver> synthesized.


=========================================================================
HDL Synthesis Report

Macro Statistics
# Registers                                            : 1
 1-bit register                                        : 1
# Latches                                              : 17
 1-bit latch                                           : 16
 8-bit latch                                           : 1
# Tristates                                            : 8
 1-bit tristate buffer                                 : 8

=========================================================================

=========================================================================
*                       Advanced HDL Synthesis                          *
=========================================================================

Analyzing FSM <FSM_1> for best encoding.
Optimizing FSM <filterRx/FSM> on signal <filterRx[1:2]> with gray encoding.
-------------------
 State | Encoding
-------------------
 s0    | 00
 s1    | 01
 s2    | 11
 s3    | 10
-------------------
Analyzing FSM <FSM_0> for best encoding.
Optimizing FSM <current_s/FSM> on signal <current_s[1:10]> with one-hot encoding.
-----------------------
 State   | Encoding
-----------------------
 rx_idle | 0000000001
 bit0    | 0000000010
 bit1    | 0000000100
 bit2    | 0000001000
 bit3    | 0000010000
 bit4    | 0000100000
 bit5    | 0001000000
 bit6    | 0010000000
 bit7    | 0100000000
 rx_stop | 1000000000
-----------------------

=========================================================================
Advanced HDL Synthesis Report

Macro Statistics
# FSMs                                                 : 2
# Registers                                            : 1
 Flip-Flops                                            : 1
# Latches                                              : 17
 1-bit latch                                           : 16
 8-bit latch                                           : 1

=========================================================================

=========================================================================
*                         Low Level Synthesis                           *
=========================================================================
WARNING:Xst:2042 - Unit serial_receiver: 8 internal tristates are replaced by logic (pull-up yes): byteReceived<0>, byteReceived<1>, byteReceived<2>, byteReceived<3>, byteReceived<4>, byteReceived<5>, byteReceived<6>, byteReceived<7>.

Optimizing unit <serial_receiver> ...

Mapping all equations...
Building and optimizing final netlist ...
Found area constraint ratio of 100 (+ 5) on block serial_receiver, actual ratio is 0.

Final Macro Processing ...

=========================================================================
Final Register Report

Macro Statistics
# Registers                                            : 13
 Flip-Flops                                            : 13

=========================================================================

=========================================================================
*                           Partition Report                            *
=========================================================================

Partition Implementation Status
-------------------------------

  No Partitions were found in this design.

-------------------------------

=========================================================================
*                            Final Report                               *
=========================================================================
Final Results
RTL Top Level Output File Name     : serial_receiver.ngr
Top Level Output File Name         : serial_receiver
Output Format                      : NGC
Optimization Goal                  : Speed
Keep Hierarchy                     : No

Design Statistics
# IOs                              : 13

Cell Usage :
# BELS                             : 39
#      GND                         : 1
#      INV                         : 3
#      LUT2                        : 12
#      LUT3                        : 8
#      LUT4                        : 14
#      VCC                         : 1
# FlipFlops/Latches                : 37
#      FDC                         : 11
#      FDCE                        : 1
#      FDP                         : 1
#      LD                          : 17
#      LDE                         : 7
# Clock Buffers                    : 2
#      BUFGP                       : 2
# IO Buffers                       : 11
#      IBUF                        : 2
#      OBUF                        : 9
=========================================================================

Device utilization summary:
---------------------------

Selected Device : 3s500efg320-4 

 Number of Slices:                       20  out of   4656     0%  
 Number of Slice Flip Flops:             29  out of   9312     0%  
 Number of 4 input LUTs:                 37  out of   9312     0%  
 Number of IOs:                          13
 Number of bonded IOBs:                  13  out of    232     5%  
    IOB Flip Flops:                       8
 Number of GCLKs:                         2  out of     24     8%  

---------------------------
Partition Resource Summary:
---------------------------

  No Partitions were found in this design.

---------------------------


=========================================================================
TIMING REPORT

NOTE: THESE TIMING NUMBERS ARE ONLY A SYNTHESIS ESTIMATE.
      FOR ACCURATE TIMING INFORMATION PLEASE REFER TO THE TRACE REPORT
      GENERATED AFTER PLACE-and-ROUTE.

Clock Information:
------------------
-----------------------------------------------------------------+--------------------------------+-------+
Clock Signal                                                     | Clock buffer(FF name)          | Load  |
-----------------------------------------------------------------+--------------------------------+-------+
baudOverSampleClk                                                | BUFGP                          | 3     |
current_s_FSM_FFd8                                               | NONE(Mtridata_byteReceived<7>) | 7     |
Mtrien_byteReceived<7>_not0001(Mtrien_byteReceived<7>_not00011:O)| NONE(*)(Mtrien_byteReceived<7>)| 1     |
Mtrien_byteReceived<6>_not0001(Mtrien_byteReceived<6>_not0001:O) | NONE(*)(Mtrien_byteReceived<6>)| 1     |
Mtrien_byteReceived<5>_not0001(Mtrien_byteReceived<5>_not00011:O)| NONE(*)(Mtrien_byteReceived<5>)| 1     |
Mtrien_byteReceived<4>_not0001(Mtrien_byteReceived<4>_not0001:O) | NONE(*)(Mtrien_byteReceived<4>)| 1     |
Mtrien_byteReceived<3>_not0001(Mtrien_byteReceived<3>_not00011:O)| NONE(*)(Mtrien_byteReceived<3>)| 1     |
Mtrien_byteReceived<2>_not0001(Mtrien_byteReceived<2>_not00011:O)| NONE(*)(Mtrien_byteReceived<2>)| 1     |
Mtrien_byteReceived<1>_not0001(Mtrien_byteReceived<1>_not00011:O)| NONE(*)(Mtrien_byteReceived<1>)| 1     |
Mtrien_byteReceived<0>_not0001(Mtrien_byteReceived<0>_not00011:O)| NONE(*)(Mtrien_byteReceived<0>)| 1     |
current_s_FSM_FFd9                                               | NONE(Mtridata_byteReceived<0>) | 1     |
baudClk                                                          | BUFGP                          | 10    |
current_s_FSM_FFd1                                               | NONE(data_byte_0)              | 8     |
-----------------------------------------------------------------+--------------------------------+-------+
(*) These 8 clock signal(s) are generated by combinatorial logic,
and XST is not able to identify which are the primary clock signals.
Please use the CLOCK_SIGNAL constraint to specify the clock signal(s) generated by combinatorial logic.
INFO:Xst:2169 - HDL ADVISOR - Some clock signals were not automatically buffered by XST with BUFG/BUFR resources. Please use the buffer_type constraint in order to insert these buffers to the clock signals to help prevent skew problems.

Asynchronous Control Signals Information:
----------------------------------------
---------------------------------------------------------------+-------------------------+-------+
Control Signal                                                 | Buffer(FF name)         | Load  |
---------------------------------------------------------------+-------------------------+-------+
current_s_FSM_Acst_FSM_inv(current_s_FSM_Acst_FSM_inv1_INV_0:O)| NONE(current_s_FSM_FFd1)| 10    |
rst                                                            | IBUF                    | 3     |
---------------------------------------------------------------+-------------------------+-------+

Timing Summary:
---------------
Speed Grade: -4

   Minimum period: 2.213ns (Maximum Frequency: 451.875MHz)
   Minimum input arrival time before clock: 5.900ns
   Maximum output required time after clock: 4.745ns
   Maximum combinational path delay: No path found

Timing Detail:
--------------
All values displayed in nanoseconds (ns)

=========================================================================
Timing constraint: Default period analysis for Clock 'baudOverSampleClk'
  Clock period: 2.213ns (frequency: 451.875MHz)
  Total number of paths / destination ports: 6 / 3
-------------------------------------------------------------------------
Delay:               2.213ns (Levels of Logic = 1)
  Source:            filterRx_FSM_FFd1 (FF)
  Destination:       filterRx_FSM_FFd2 (FF)
  Source Clock:      baudOverSampleClk rising
  Destination Clock: baudOverSampleClk rising

  Data Path: filterRx_FSM_FFd1 to filterRx_FSM_FFd2
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     FDC:C->Q              3   0.591   0.610  filterRx_FSM_FFd1 (filterRx_FSM_FFd1)
     LUT2:I1->O            1   0.704   0.000  filterRx_FSM_FFd2-In1 (filterRx_FSM_FFd2-In)
     FDC:D                     0.308          filterRx_FSM_FFd2
    ----------------------------------------
    Total                      2.213ns (1.603ns logic, 0.610ns route)
                                       (72.4% logic, 27.6% route)

=========================================================================
Timing constraint: Default period analysis for Clock 'current_s_FSM_FFd8'
  Clock period: 2.170ns (frequency: 460.829MHz)
  Total number of paths / destination ports: 6 / 6
-------------------------------------------------------------------------
Delay:               2.170ns (Levels of Logic = 1)
  Source:            Mtridata_byteReceived<7> (LATCH)
  Destination:       Mtridata_byteReceived<7> (LATCH)
  Source Clock:      current_s_FSM_FFd8 rising
  Destination Clock: current_s_FSM_FFd8 rising

  Data Path: Mtridata_byteReceived<7> to Mtridata_byteReceived<7>
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     LDE:G->Q              2   0.676   0.482  Mtridata_byteReceived<7> (Mtridata_byteReceived<7>)
     LUT3:I2->O            1   0.704   0.000  Mtridata_byteReceived<7>_mux00001 (Mtridata_byteReceived<7>_mux0000)
     LDE:D                     0.308          Mtridata_byteReceived<7>
    ----------------------------------------
    Total                      2.170ns (1.688ns logic, 0.482ns route)
                                       (77.8% logic, 22.2% route)

=========================================================================
Timing constraint: Default period analysis for Clock 'baudClk'
  Clock period: 1.950ns (frequency: 512.821MHz)
  Total number of paths / destination ports: 9 / 9
-------------------------------------------------------------------------
Delay:               1.950ns (Levels of Logic = 0)
  Source:            current_s_FSM_FFd10 (FF)
  Destination:       current_s_FSM_FFd9 (FF)
  Source Clock:      baudClk rising
  Destination Clock: baudClk rising

  Data Path: current_s_FSM_FFd10 to current_s_FSM_FFd9
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     FDP:C->Q             17   0.591   1.051  current_s_FSM_FFd10 (current_s_FSM_FFd10)
     FDC:D                     0.308          current_s_FSM_FFd9
    ----------------------------------------
    Total                      1.950ns (0.899ns logic, 1.051ns route)
                                       (46.1% logic, 53.9% route)

=========================================================================
Timing constraint: Default OFFSET IN BEFORE for Clock 'baudOverSampleClk'
  Total number of paths / destination ports: 3 / 3
-------------------------------------------------------------------------
Offset:              3.287ns (Levels of Logic = 2)
  Source:            serial_in (PAD)
  Destination:       syncDetected (FF)
  Destination Clock: baudOverSampleClk rising

  Data Path: serial_in to syncDetected
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     IBUF:I->O            10   1.218   1.057  serial_in_IBUF (serial_in_IBUF)
     LUT2:I0->O            1   0.704   0.000  filterRx_FSM_FFd2-In1 (filterRx_FSM_FFd2-In)
     FDC:D                     0.308          filterRx_FSM_FFd2
    ----------------------------------------
    Total                      3.287ns (2.230ns logic, 1.057ns route)
                                       (67.8% logic, 32.2% route)

=========================================================================
Timing constraint: Default OFFSET IN BEFORE for Clock 'current_s_FSM_FFd8'
  Total number of paths / destination ports: 8 / 7
-------------------------------------------------------------------------
Offset:              5.900ns (Levels of Logic = 4)
  Source:            serial_in (PAD)
  Destination:       Mtridata_byteReceived<6> (LATCH)
  Destination Clock: current_s_FSM_FFd8 rising

  Data Path: serial_in to Mtridata_byteReceived<6>
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     IBUF:I->O            10   1.218   1.057  serial_in_IBUF (serial_in_IBUF)
     LUT3:I0->O            3   0.704   0.610  Mtridata_byteReceived<6>_mux000021 (N8)
     LUT3:I1->O            1   0.704   0.595  Mtridata_byteReceived<6>_mux0000_SW0 (N17)
     LUT4:I0->O            1   0.704   0.000  Mtridata_byteReceived<6>_mux0000 (Mtridata_byteReceived<6>_mux0000)
     LDE:D                     0.308          Mtridata_byteReceived<6>
    ----------------------------------------
    Total                      5.900ns (3.638ns logic, 2.262ns route)
                                       (61.7% logic, 38.3% route)

=========================================================================
Timing constraint: Default OFFSET IN BEFORE for Clock 'current_s_FSM_FFd9'
  Total number of paths / destination ports: 1 / 1
-------------------------------------------------------------------------
Offset:              2.408ns (Levels of Logic = 1)
  Source:            serial_in (PAD)
  Destination:       Mtridata_byteReceived<0> (LATCH)
  Destination Clock: current_s_FSM_FFd9 falling

  Data Path: serial_in to Mtridata_byteReceived<0>
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     IBUF:I->O            10   1.218   0.882  serial_in_IBUF (serial_in_IBUF)
     LD:D                      0.308          Mtridata_byteReceived<0>
    ----------------------------------------
    Total                      2.408ns (1.526ns logic, 0.882ns route)
                                       (63.4% logic, 36.6% route)

=========================================================================
Timing constraint: Default OFFSET OUT AFTER for Clock 'baudClk'
  Total number of paths / destination ports: 1 / 1
-------------------------------------------------------------------------
Offset:              4.745ns (Levels of Logic = 1)
  Source:            current_s_FSM_FFd1 (FF)
  Destination:       data_ready (PAD)
  Source Clock:      baudClk rising

  Data Path: current_s_FSM_FFd1 to data_ready
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     FDCE:C->Q            10   0.591   0.882  current_s_FSM_FFd1 (current_s_FSM_FFd1)
     OBUF:I->O                 3.272          data_ready_OBUF (data_ready)
    ----------------------------------------
    Total                      4.745ns (3.863ns logic, 0.882ns route)
                                       (81.4% logic, 18.6% route)

=========================================================================
Timing constraint: Default OFFSET OUT AFTER for Clock 'current_s_FSM_FFd1'
  Total number of paths / destination ports: 8 / 8
-------------------------------------------------------------------------
Offset:              4.368ns (Levels of Logic = 1)
  Source:            data_byte_7 (LATCH)
  Destination:       data_byte<7> (PAD)
  Source Clock:      current_s_FSM_FFd1 falling

  Data Path: data_byte_7 to data_byte<7>
                                Gate     Net
    Cell:in->out      fanout   Delay   Delay  Logical Name (Net Name)
    ----------------------------------------  ------------
     LD:G->Q               1   0.676   0.420  data_byte_7 (data_byte_7)
     OBUF:I->O                 3.272          data_byte_7_OBUF (data_byte<7>)
    ----------------------------------------
    Total                      4.368ns (3.948ns logic, 0.420ns route)
                                       (90.4% logic, 9.6% route)

=========================================================================


Total REAL time to Xst completion: 3.00 secs
Total CPU time to Xst completion: 3.32 secs
 
--> 

Total memory usage is 258164 kilobytes

Number of errors   :    0 (   0 filtered)
Number of warnings :   19 (   0 filtered)
Number of infos    :    9 (   0 filtered)

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.