Subversion Repositories usb_fpga_1_2

/*!
   ZTEX Firmware Kit for EZ-USB FX2 Microcontrollers
   Copyright (C) 2009-2011 ZTEX GmbH.
   http://www.ztex.de
 
   This program is free software; you can redistribute it and/or modify
   it under the terms of the GNU General Public License version 3 as
   published by the Free Software Foundation.
 
   This program is distributed in the hope that it will be useful, but
   WITHOUT ANY WARRANTY; without even the implied warranty of
   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
   General Public License for more details.
 
   You should have received a copy of the GNU General Public License
   along with this program; if not, see http://www.gnu.org/licenses/.
!*/
 
/*
    FPGA support for ZTEX USB FPGA Modules 1.10
*/    
 
#ifndef[ZTEX_FPGA_H]
#define[ZTEX_FPGA_H]
 
#define[@CAPABILITY_FPGA;]
 
__xdata BYTE fpga_checksum;         // checksum
__xdata DWORD fpga_bytes;           // transfered bytes
__xdata BYTE fpga_init_b;           // init_b state (should be 222 after configuration)
__xdata BYTE fpga_flash_result;     // result of automatic fpga configuarion from Flash
 
/* *********************************************************************
   ***** reset_fpga ****************************************************
   ********************************************************************* */
static void reset_fpga_int (BYTE mode) {		// reset FPGA
    unsigned short k;
    IFCONFIG = bmBIT7;
    SYNCDELAY; 
    PORTACFG = 0;
    PORTCCFG = 0;
 
    OEA = (OEA & 0xe0) | bmBIT1 | bmBIT3 | bmBIT4;
    IOA = (IOA & 0xe0) | bmBIT4;
    wait(10);
 
    OEC = bmBIT4 | bmBIT6 | bmBIT7;
    IOC = mode;
 
    IOA = (IOA & 0xe0) | bmBIT1;				// ready for configuration
    k=0;
    while (!IOA0 && k<65535)
	k++;
 
    fpga_init_b = IOA0 ? 200 : 100;
    fpga_bytes = 0;
    fpga_checksum = 0;
}    
 
static void reset_fpga () {
    reset_fpga_int(bmBIT4);
}
 
static void reset_fpga_flash () {
    reset_fpga_int(bmBIT4 | bmBIT6);
}
 
/* *********************************************************************
   ***** init_fpga_configuration ***************************************
   ********************************************************************* */
static void init_fpga_configuration () {
    {
	PRE_FPGA_RESET
    }
    reset_fpga();			// reset FPGA
}    
 
/* *********************************************************************
   ***** post_fpga_confog **********************************************
   ********************************************************************* */
static void post_fpga_config () {
    POST_FPGA_CONFIG
}
 
/* *********************************************************************
   ***** finish_fpga_configuration *************************************
   ********************************************************************* */
static void finish_fpga_configuration () {
    WORD w;
    fpga_init_b += IOA0 ? 20 : 10;
 
    for ( w=0; w<65535; w++ ) {
        IOA3 = 1; IOA3 = 0; 
    }
 
    IOA3 = 1; IOA3 = 0;
    IOA3 = 1; IOA3 = 0;
    IOA3 = 1; IOA3 = 0;
    IOA3 = 1; IOA3 = 0;
    IOA4 = 1;
    IOA3 = 1; IOA3 = 0;
    OEC = 0;
    IOA3 = 1; IOA3 = 0;
    IOA3 = 1; IOA3 = 0;
    IOA3 = 1; IOA3 = 0;
 
    OEA = OEA & 0xe0;
    fpga_init_b += IOA0 ? 2 : 1;
    if ( IOA1 )  {
	IOA1 = 1;		
	post_fpga_config();
    }
 
    IOA1 = 1;		
    OEA |= bmBIT1; 
}    
 
 
/* *********************************************************************
   ***** EP0 vendor request 0x30 ***************************************
   ********************************************************************* */
ADD_EP0_VENDOR_REQUEST((0x30,,		// get FPGA state
    MEM_COPY1(fpga_checksum,EP0BUF+1,7);    
    OEA &= ~bmBIT1;
    if ( IOA1 )  {
	EP0BUF[0] = 0; 	 		// FPGA configured 
	IOA1 = 1;		
	OEA |= bmBIT1;
    }
    else {
        EP0BUF[0] = 1;			// FPGA unconfigured 
	reset_fpga();			// prepare FPGA for configuration
    }
    EP0BUF[8] = 1;			// bit order for bitstream in Flash memory: swapped
 
    EP0BCH = 0;
    EP0BCL = 9;
,,));;
 
 
/* *********************************************************************
   ***** EP0 vendor command 0x31 ***************************************
   ********************************************************************* */
ADD_EP0_VENDOR_COMMAND((0x31,,init_fpga_configuration();,,));;	// reset FPGA
 
 
/* *********************************************************************
   ***** EP0 vendor command 0x32 ***************************************
   ********************************************************************* */
void fpga_send_ep0() {
    BYTE oOED;
    oOED = OED;
    OED = 255;
    fpga_bytes += ep0_payload_transfer;
    __asm
	mov	dptr,#_EP0BCL
	movx	a,@dptr
	jz 	010000$
  	mov	r2,a
	mov 	_AUTOPTRL1,#(_EP0BUF)
	mov 	_AUTOPTRH1,#(_EP0BUF >> 8)
	mov 	_AUTOPTRSETUP,#0x07
	mov	dptr,#_fpga_checksum
	movx 	a,@dptr
	mov 	r1,a
	mov	dptr,#_XAUTODAT1
010001$:
	movx	a,@dptr
	mov	_IOD,a
	setb	_IOA3
	add 	a,r1
	mov 	r1,a
	clr	_IOA3
	djnz	r2, 010001$
 
	mov	dptr,#_fpga_checksum
	mov	a,r1
	movx	@dptr,a
 
010000$:
    	__endasm; 
    OED = oOED;
    if ( EP0BCL<64 ) {
    	finish_fpga_configuration();
    } 
}
 
ADD_EP0_VENDOR_COMMAND((0x32,,		// send FPGA configuration data
,,
    fpga_send_ep0();
));;
 
 
#ifeq[FLASH_BITSTREAM_ENABLED][1]
#ifeq[FLASH_ENABLED][1]
 
/* *********************************************************************
   ***** fpga_send_bitstream_from_flash ********************************
   ********************************************************************* */
void fpga_send_bitstream_from_flash (WORD size) {
	size;			// this avoids stupid warnings
__asm
	push 	_OED
	mov	_OED,#0
 
	mov	r5,dpl		// = size
	mov	r6,dph
 
	// fpga_bytes+=size
	mov	dptr,#_fpga_bytes
	movx	a,@dptr
	mov	r1,a
	inc	dptr
	movx	a,@dptr
	mov	r2,a
	inc	dptr
	movx	a,@dptr
	mov	r3,a
	inc	dptr
	movx	a,@dptr
	mov	r4,a
 
	mov	dptr,#_fpga_bytes
	mov	a,r5
	add	a,r1
	movx	@dptr,a
	mov	a,r6
	addc	a,r2
	inc	dptr
	movx	@dptr,a
	mov	a,#0
	addc	a,r3
	inc	dptr
	movx	@dptr,a
	mov	a,#0
	addc	a,r4
	inc	dptr
	movx	@dptr,a
 
010003$:
	cjne	r5,#0x00,010002$
	cjne	r6,#0x00,010002$
	pop 	_OED
	ret
010002$:
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
	mov 	_IOA,#(bmBIT1 | bmBIT6 | bmBIT3 | bmBIT7)
	mov 	_IOA,#(bmBIT1 | bmBIT6)
 
	dec	r5
	cjne	r5,#0xff,010003$
	dec	r6 
	sjmp	010003$
__endasm;    
}
 
#include[ztex-fpga-flash.h]
 
#else
#warning[Flash interface is not enabled but required for FPGA configuration using a bitstream from Flash meomory]
#define[FLASH_BITSTREAM_ENABLED][0]
#endif
#endif
 
#endif  /*ZTEX_FPGA_H*/