Subversion Repositories w11

-- $Id: sys_tst_snhumanio_n3.vhd 433 2011-11-27 22:04:39Z mueller $
--
-- Copyright 2011- by Walter F.J. Mueller <W.F.J.Mueller@gsi.de>
--
-- This program is free software; you may redistribute and/or modify it under
-- the terms of the GNU General Public License as published by the Free
-- Software Foundation, either version 2, or at your option any later version.
--
-- This program is distributed in the hope that it will be useful, but
-- WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY
-- or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
-- for complete details.
--
------------------------------------------------------------------------------
-- Module Name:    sys_tst_snhumanio_n3 - syn
-- Description:    snhumanio tester design for nexys3
--
-- Dependencies:   vlib/genlib/clkdivce
--                 bplib/bpgen/sn_humanio
--                 tst_snhumanio
--                 vlib/nxcramlib/nx_cram_dummy
--
-- Test bench:     -
--
-- Target Devices: generic
-- Tool versions:  xst 13.1; ghdl 0.29
--
-- Synthesized (xst):
-- Date         Rev  ise         Target      flop lutl lutm slic t peri
-- 2011-11-27   433 13.1    O40d xc3s1200e-4  151  195    -   65 t  6.1
--
-- Revision History: 
-- Date         Rev Version  Comment
-- 2011-11-27   433   1.0    Initial version
------------------------------------------------------------------------------
-- Usage of Nexys 2 Switches, Buttons, LEDs:
--
 
library ieee;
use ieee.std_logic_1164.all;
 
use work.slvtypes.all;
use work.genlib.all;
use work.bpgenlib.all;
use work.nxcramlib.all;
use work.sys_conf.all;
 
-- ----------------------------------------------------------------------------
 
entity sys_tst_snhumanio_n3 is          -- top level
                                        -- implements nexys3_aif
  port (
    I_CLK100 : in slbit;                -- 100  MHz clock
    I_RXD : in slbit;                   -- receive data (board view)
    O_TXD : out slbit;                  -- transmit data (board view)
    I_SWI : in slv8;                    -- n3 switches
    I_BTN : in slv5;                    -- n3 buttons
    O_LED : out slv8;                   -- n3 leds
    O_ANO_N : out slv4;                 -- 7 segment disp: anodes   (act.low)
    O_SEG_N : out slv8;                 -- 7 segment disp: segments (act.low)
    O_MEM_CE_N : out slbit;             -- cram: chip enable   (act.low)
    O_MEM_BE_N : out slv2;              -- cram: byte enables  (act.low)
    O_MEM_WE_N : out slbit;             -- cram: write enable  (act.low)
    O_MEM_OE_N : out slbit;             -- cram: output enable (act.low)
    O_MEM_ADV_N  : out slbit;           -- cram: address valid (act.low)
    O_MEM_CLK : out slbit;              -- cram: clock
    O_MEM_CRE : out slbit;              -- cram: command register enable
    I_MEM_WAIT : in slbit;              -- cram: mem wait
    O_MEM_ADDR  : out slv23;            -- cram: address lines
    IO_MEM_DATA : inout slv16;          -- cram: data lines
    O_PPCM_CE_N : out slbit;            -- ppcm: ...
    O_PPCM_RST_N : out slbit            -- ppcm: ...
  );
end sys_tst_snhumanio_n3;
 
architecture syn of sys_tst_snhumanio_n3 is
 
  signal CLK :   slbit := '0';
 
  signal SWI     : slv8  := (others=>'0');
  signal BTN     : slv5  := (others=>'0');
  signal LED     : slv8  := (others=>'0');
  signal DSP_DAT : slv16 := (others=>'0');
  signal DSP_DP  : slv4  := (others=>'0');
 
  signal RESET   : slbit := '0';
  signal CE_MSEC : slbit := '0';
 
begin
 
  RESET <= '0';                         -- so far not used
 
  CLK <= I_CLK100;
 
  CLKDIV : clkdivce
    generic map (
      CDUWIDTH => 7,
      USECDIV  => 100,
      MSECDIV  => 1000)
    port map (
      CLK     => CLK,
      CE_USEC => open,
      CE_MSEC => CE_MSEC
    );
 
  HIO : sn_humanio
    generic map (
      BWIDTH   => 5,
      DEBOUNCE => sys_conf_hio_debounce)
    port map (
      CLK     => CLK,
      RESET   => RESET,
      CE_MSEC => CE_MSEC,
      SWI     => SWI,                   
      BTN     => BTN,                   
      LED     => LED,                   
      DSP_DAT => DSP_DAT,               
      DSP_DP  => DSP_DP,
      I_SWI   => I_SWI,                 
      I_BTN   => I_BTN,
      O_LED   => O_LED,
      O_ANO_N => O_ANO_N,
      O_SEG_N => O_SEG_N
    );
 
  HIOTEST : entity work.tst_snhumanio
    generic map (
      BWIDTH => 5)
    port map (
      CLK     => CLK,
      RESET   => RESET,
      CE_MSEC => CE_MSEC,
      SWI     => SWI,
      BTN     => BTN,
      LED     => LED,
      DSP_DAT => DSP_DAT,
      DSP_DP  => DSP_DP
    );
 
  O_TXD <= I_RXD;
 
  SRAM_PROT : nx_cram_dummy            -- connect CRAM to protection dummy
    port map (
      O_MEM_CE_N  => O_MEM_CE_N,
      O_MEM_BE_N  => O_MEM_BE_N,
      O_MEM_WE_N  => O_MEM_WE_N,
      O_MEM_OE_N  => O_MEM_OE_N,
      O_MEM_ADV_N => O_MEM_ADV_N,
      O_MEM_CLK   => O_MEM_CLK,
      O_MEM_CRE   => O_MEM_CRE,
      I_MEM_WAIT  => I_MEM_WAIT,
      O_MEM_ADDR  => O_MEM_ADDR,
      IO_MEM_DATA => IO_MEM_DATA
    );
 
  O_PPCM_CE_N  <= '1';                  -- keep parallel PCM memory disabled
  O_PPCM_RST_N <= '1';                  --
 
end syn;