URL
https://opencores.org/ocsvn/w11/w11/trunk
Subversion Repositories w11
[/] [w11/] [tags/] [w11a_V0.6/] [rtl/] [vlib/] [serport/] [serport_uart_tx.vhd] - Rev 27
Go to most recent revision | Compare with Previous | Blame | View Log
-- $Id: serport_uart_tx.vhd 417 2011-10-22 10:30:29Z mueller $ -- -- Copyright 2007-2011 by Walter F.J. Mueller <W.F.J.Mueller@gsi.de> -- -- This program is free software; you may redistribute and/or modify it under -- the terms of the GNU General Public License as published by the Free -- Software Foundation, either version 2, or at your option any later version. -- -- This program is distributed in the hope that it will be useful, but -- WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY -- or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License -- for complete details. -- ------------------------------------------------------------------------------ -- Module Name: serport_uart_tx - syn -- Description: serial port UART - transmitter -- -- Dependencies: - -- Test bench: tb/tb_serport_uart_rxtx -- Target Devices: generic -- Tool versions: xst 8.2, 9.1, 9.2, 13.1; ghdl 0.18-0.29 -- Revision History: -- Date Rev Version Comment -- 2011-10-22 417 1.0.4 now numeric_std clean -- 2007-10-21 91 1.0.3 use 1 stop bits (redesigned _rx allows this) -- 2007-10-19 90 1.0.2 use 2 stop bits (allow CLKDIV=0 operation in sim) -- 2007-10-12 88 1.0.1 avoid ieee.std_logic_unsigned, use cast to unsigned -- 2007-06-30 62 1.0 Initial version ------------------------------------------------------------------------------ library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; use work.slvtypes.all; entity serport_uart_tx is -- serial port uart: transmit part generic ( CDWIDTH : positive := 13); -- clk divider width port ( CLK : in slbit; -- clock RESET : in slbit; -- reset CLKDIV : in slv(CDWIDTH-1 downto 0); -- clock divider setting TXSD : out slbit; -- transmit serial data (uart view) TXDATA : in slv8; -- transmit data in TXENA : in slbit; -- transmit data enable TXBUSY : out slbit -- transmit busy ); end serport_uart_tx; architecture syn of serport_uart_tx is type regs_type is record ccnt : slv(CDWIDTH-1 downto 0); -- clock divider counter bcnt : slv4; -- bit counter sreg : slv9; -- output shift register busy : slbit; end record regs_type; constant cntzero : slv(CDWIDTH-1 downto 0) := (others=>'0'); constant regs_init : regs_type := ( cntzero, (others=>'0'), (others=>'1'), -- sreg to all 1 !! '0' ); signal R_REGS : regs_type := regs_init; -- state registers signal N_REGS : regs_type := regs_init; -- next value state regs begin proc_regs: process (CLK) begin if rising_edge(CLK) then R_REGS <= N_REGS; end if; end process proc_regs; proc_next: process (R_REGS, RESET, CLKDIV, TXDATA, TXENA) variable r : regs_type := regs_init; variable n : regs_type := regs_init; variable ld_ccnt : slbit := '0'; begin r := R_REGS; n := R_REGS; ld_ccnt := '0'; if r.busy = '0' then ld_ccnt := '1'; n.bcnt := (others=>'0'); if TXENA = '1' then n.sreg := TXDATA & '0'; -- add start (0) bit n.busy := '1'; end if; else if unsigned(r.ccnt) = 0 then ld_ccnt := '1'; n.sreg := '1' & r.sreg(8 downto 1); n.bcnt := slv(unsigned(r.bcnt) + 1); if unsigned(r.bcnt) = 9 then -- if 10 bits send n.busy := '0'; -- declare all done end if; end if; end if; if RESET = '1' then ld_ccnt := '1'; n.busy := '0'; end if; if ld_ccnt = '1' then n.ccnt := CLKDIV; else n.ccnt := slv(unsigned(r.ccnt) - 1); end if; N_REGS <= n; TXBUSY <= r.busy; TXSD <= r.sreg(0); end process proc_next; end syn;
Go to most recent revision | Compare with Previous | Blame | View Log