URL
https://opencores.org/ocsvn/w11/w11/trunk
Subversion Repositories w11
[/] [w11/] [tags/] [w11a_V0.7/] [doc/] [w11a_os_guide.txt] - Rev 29
Go to most recent revision | Compare with Previous | Blame | View Log
# $Id: w11a_os_guide.txt 654 2015-03-01 18:45:38Z mueller $
Guide to run operating system images on w11a systems
Table of content:
1. I/O emulation setup
2. FPGA Board setup
3. Rlink and Backend Server setup
4. simh simulator setup
5. oskits
a. Unix systems
b. DEC operating systems
1. I/O emulation setup ----------------------------------------------------
All UNIBUS peripherals which exchange data (currently DL11, LP11, PC11, RK11,
and RL11) are currently emulated via a backend process. The communication
between FPGA board and backend server can be via
- Serial port
- via an integrated USB-UART bridge
- on basys3 and nexys4 with a FT2232HQ, allows up to 12M Baud
- on nexys3 with a FT232R, allows up to 2M Baud
- via RS232 port, as on s3board and nexys2
- using a serial port (/dev/ttySx) is limited to 115 kBaud on most PCs.
- using a USB-RS232 adapter was tested up to 460k Baud.
- Direct USB connection using a Cypress FX2 USB controller
- is supported on the nexys2 and nexys3 FPGA boards
- much faster than serial port connections (see below)
- also allows to configure the FPGA over the same USB connection
Notes:
- A 10M Baud connection, like on a nexys4, gives disk access rates and
throughputs much better than the real hardware of the 70's and is well
suitable for practical usage.
- In an OS with good disk caching like 2.11BSD the impact of disk speed
is actually smaller than the bare numbers suggest.
- A 460k Baud connection gives in practice a disk throughput of ~20 kB/s.
This allows to test the system but is a bit slow for real usage.
- USB-RS232 cables with a FTDI FT232R chip work fine, tests with Prolific
Technology PL2303 based cable never gave reliable connections for higher
Baud rates.
Recommended setup for best performance (boards ordered by vintage):
Board Channel/Interface nom. speed peak transfer rate
basys3 USB-UART bridge 10M Baud 910 kB/sec
nexys4 USB-UART bridge 10M Baud 910 kb/sec
nexys3 Cypress FX2 USB USB2.0 speed 30000 kB/sec
nexys2 Cypress FX2 USB USB2.0 speed 30000 kB/sec
s3board RS232+USB-RS232 cable 460k Baud 41 kB/sec
2. FPGA Board setup -------------------------------------------------------
Recommended setups
- Basys3
- connect USB cable to micro-USB connector labeled 'PROG'
- to configure via vivado hardware server
make <sys>.vconfig
- Nexys4
- connect USB cable to micro-USB connector labeled 'PROG'
- to configure via vivado hardware server
make <sys>.vconfig
- Nexys3
- use Cypress FX for configure and and rlink communication
- connect USB cable to micro-USB connector labeled 'USB PROG'
- to configure via FX2 and jtag tool
make <sys>.jconfig
- Nexys2
- connect USB cable to mini-USB connector (between RS232 and PS/2 port)
- to configure via FX2 and jtag tool
make <sys>.jconfig
- S3board
- connect the USB-RS232 cable to the RS232 port
- connect a JTAG programmer (e.g. Xilinx USB Cable II) to JTAG pins
- to configure via ISE Impact
make <sys>.iconfig
3. Rlink and Backend Server setup -----------------------------------------
All examples below use the same basic setup
- setup vt100 emulator windows
cd $RETROBASE/tools/oskit/<oskit-name>
console_starter -d DL0 &
console_starter -d DL1 &
- setup rlink connection using ti_rri backend server via the ti_w11
quick start wrapper script. Ensure that all 8 switches on the board
are in the indicated positions (SWI=...). The concrete boot script
name <boot-script> is given in the following sections
- for b3 over serial
SWI = 00000000 00101010
ti_w11 -tu<dn>,10M,break,xon @<oskit-name>_boot.tcl
NOTE: the basys3 w11a has only 176 kB memory (all from BRAMS!)
unix-v5 works fine. XXDP, RT11 and RSX-11M should work.
211bsd will not boot, either most RSX-11M+ systems.
- for n4 over serial
SWI = 00000000 00101000
ti_w11 -tu<dn>,10M,break,cts @<oskit-name>_boot.tcl
- for n2,n3 over fx2
SWI = 00101100
ti_w11 -u @<oskit-name>_boot.tcl
- for s3 serial
SWI = 00101010
ti_w11 -tu<dn>,460k,break,xon @<oskit-name>_boot.tcl
Notes:
- on <dn>, the serial device number
- check with 'ls /dev/ttyUSB*' to see what is available
- <dn> is typically '1' if only a single basys3 or nexys4 is connected
Initially two ttyUSB devices show up, the lower is for FPGA config
and will disappear when Vivado hardware server is used once. The
upper provides the data connection.
- <dn> is typically '0' if only a single USB-RS232 cable is connected
- on LED display
- is controlled by SWI(3)
0 -> system status
1 -> DR emulation --> OS specific light patterns
- on Hex display
- is controlled by SWI(5:4)
- boards with a 4 digit display
00 -> serial link rate divider
01 -> PC
10 -> DISPREG
11 -> DR emulation
- boards with 8 digit display
- SWI(5) select for DSP(7:4) display
0 -> serial link rate divider
1 -> PC
- SWI(4) select for DSP(3:0) display
0 -> DISPREG
1 -> DR emulation
4. simh simulator setup ---------------------------------------------------
Sometimes it is good to compare the w11a behaviour with the PDP-11 software
emulator from the simh project (see http://simh.trailing-edge.com/).
Under $RETROBASE/tools/simh two setup files are provided with configure
simh to reflect the w11a setup as close as possible:
- setup_w11a_min.scmd
Very close the current w11a state when it runs on an s3board
- processor: 11/70, no FPP, 1 Mbyte
- periphery: 2 DL11, LP11, RK11, PC11
- setup_w11a_max.scmd
Planned configuration for the w11a, in addition
- processor: 4 Mbyte memory (as on Nexys2, Nexys3,...)
- periphery: DZ11, RL11/RL02, RK70/RP06, TM11/TU10
Startup scripts are provided with each oskit. They call the w11a_max
configuration, so will show in the emulator what w11a can do when
finished.
All examples below use the same basic setup
- setup vt100 emulator window for 2nd DL11
cd $RETROBASE/tools/oskit/<oskit-name>
console_starter -s -d DL1 &
{Note: the -s ensures that the port numbers used by simh are taken!}
- start the simulator
pdp11 <oskit-name>_boot.scmd
5. oskits -----------------------------------------------------------------
Ready to be used 'oskits' are provided under
$RETROBASE/tools/oskit/<oskit-name>
The tarballs with the disk images are provided from a web server
and have to be installed separately.
5a. Unix systems -----------------------------------------------------
Legal and license issues:
Ancient UNIX systems for the PDP-11 can now be freely used under the
'Caldera license'. 2.11BSD was released 1992 under the 4 clause BSD
license. Taken together
- Unix V1 to V7
- all BSD Unix versions for PDP-11
can be freely distributed and used for non-commercial purposes.
Two oskits are currently provided:
- unix-v5_rk: Unix V5 System on RK05
- 211bsd_rk: 2.11BSD system on RK05
- 211bsd_rl: 2.11BSD system on RL02
For further details consult the README_<oskit-name>set.txt file in the
oskit directory.
5b. DEC operating systems --------------------------------------------
Legal and license issues:
Unfortunately there is no general hobbyist license for DEC operating
systems for PDP-11 computers. The 'Mentec license' is commonly understood
to cover the some older versions of DEC operating systems, for example
- RT-11 V5.3 or prior
- RSX-11M V4.3 or prior
- RSX-11M PLUS V3.0 or prior
on a simulator. It is commonly assumed that the license terms cover the
usage of the PDP11 simulator from the 'simh' suite. Usage of the e11
simulator is not covered according to the author of e11.
HOWEVER: THIS LICENSE DOES NOT COVER THE USAGE OF THESE HISTORIC DEC
OPERATING SYSTEMS ON ANY 'REAL HARDWARE' IMPLEMENTATION OF A
PDP-11. SO USAGE ON THE W11 IS *NOT* COVERED BY THE
'Mentec-license'.
Some oskits are provided with systems sysgen'ed to run on a configuration
like the w11a.
- Feel free to explore them with the simh simulator.
The boot scripts for simh are included ( <kit>.simh )
- In case you happen to have a valid license feel free to try them
out the W11A and let the author know whether is works as it should.
For convenience the boot scripts are also included ( <kit>.tcl ).
Several osskits are currently provided
- rsx11m-31_rk: RSX-11M V3.1 on RK05
- rsx11m-40_rk: RSX-11M V4.0 on RK05
- rt11-40_rk: RT-11 V4.0 on RK05
- rt11-53_rl: RT-11 V5.3 on RL02
- xxdp_rl: XXDP 22 and 25 on RL02
For further details consult the README_<oskit-name>set.txt file in the
oskit directory.
Go to most recent revision | Compare with Previous | Blame | View Log