URL
https://opencores.org/ocsvn/w11/w11/trunk
Subversion Repositories w11
[/] [w11/] [tags/] [w11a_V0.74/] [rtl/] [bplib/] [bpgen/] [sn_7segctl.vhd] - Rev 36
Go to most recent revision | Compare with Previous | Blame | View Log
-- $Id: sn_7segctl.vhd 750 2016-03-24 23:11:51Z mueller $ -- -- Copyright 2007-2015 by Walter F.J. Mueller <W.F.J.Mueller@gsi.de> -- -- This program is free software; you may redistribute and/or modify it under -- the terms of the GNU General Public License as published by the Free -- Software Foundation, either version 2, or at your option any later version. -- -- This program is distributed in the hope that it will be useful, but -- WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY -- or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License -- for complete details. -- ------------------------------------------------------------------------------ -- Module Name: sn_7segctl - syn -- Description: 7 segment display controller (for s3board,nexys,basys) -- -- Dependencies: - -- Test bench: - -- Target Devices: generic -- Tool versions: ise 8.2-14.7; viv 2014.4; ghdl 0.18-0.31 -- -- Synthesized (xst): -- Date Rev ise Target flop lutl lutm slic t peri -- 2015-01-24 637 14.7 131013 xc6slx16-2 9 27 0 16 s 3.1 ns DC=3 -- 2015-01-24 637 14.7 131013 xc6slx16-2 8 19 0 9 s 3.1 ns DC=2 -- 2015-01-24 410 14.7 131013 xc6slx16-2 8 19 0 8 s 3.1 ns -- Revision History: -- Date Rev Version Comment -- 2015-01-24 637 1.3 renamed from sn_4x7segctl; add DCWIDTH, -- allow 4(DC=2) or 8(DC=3) digit display -- 2011-09-17 410 1.2.1 now numeric_std clean -- 2011-07-30 400 1.2 digit dark in last quarter (not 16 clocks) -- 2011-07-08 390 1.1.2 renamed from s3_dispdrv -- 2010-04-17 278 1.1.1 renamed from dispdrv -- 2010-03-29 272 1.1 add all ANO off time to allow to driver turn-off -- delay and to avoid cross talk between digits -- 2007-12-16 101 1.0.1 use _N for active low -- 2007-09-16 83 1.0 Initial version ------------------------------------------------------------------------------ library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; use work.slvtypes.all; entity sn_7segctl is -- 7 segment display controller generic ( DCWIDTH : positive := 2; -- digit counter width (2 or 3) CDWIDTH : positive := 6); -- clk divider width (must be >= 5) port ( CLK : in slbit; -- clock DIN : in slv(4*(2**DCWIDTH)-1 downto 0); -- data 16 or 32 DP : in slv((2**DCWIDTH)-1 downto 0); -- decimal points 4 or 8 ANO_N : out slv((2**DCWIDTH)-1 downto 0); -- anodes (act.low) 4 or 8 SEG_N : out slv8 -- segements (act.low) ); end sn_7segctl; architecture syn of sn_7segctl is type regs_type is record cdiv : slv(CDWIDTH-1 downto 0); -- clock divider counter dcnt : slv(DCWIDTH-1 downto 0); -- digit counter end record regs_type; constant regs_init : regs_type := ( slv(to_unsigned(0,CDWIDTH)), -- cdiv slv(to_unsigned(0,DCWIDTH)) -- dcnt ); type hex2segtbl_type is array (0 to 15) of slv7; constant hex2segtbl : hex2segtbl_type := ("0111111", -- 0: "0000" "0000110", -- 1: "0001" "1011011", -- 2: "0010" "1001111", -- 3: "0011" "1100110", -- 4: "0100" "1101101", -- 5: "0101" "1111101", -- 6: "0110" "0000111", -- 7: "0111" "1111111", -- 8: "1000" "1101111", -- 9: "1001" "1110111", -- a: "1010" "1111100", -- b: "1011" "0111001", -- c: "1100" "1011110", -- d: "1101" "1111001", -- e: "1110" "1110001" -- f: "1111" ); signal R_REGS : regs_type := regs_init; -- state registers signal N_REGS : regs_type := regs_init; -- next value state regs signal CHEX : slv4 := (others=>'0'); -- current hex number signal CDP : slbit := '0'; -- current decimal point begin assert DCWIDTH=2 or DCWIDTH=3 report "assert(DCWIDTH=2 or DCWIDTH=3): unsupported DCWIDTH" severity failure; assert CDWIDTH >= 5 report "assert(CDWIDTH >= 5): CDWIDTH too small" severity failure; proc_regs: process (CLK) begin if rising_edge(CLK) then R_REGS <= N_REGS; end if; end process proc_regs; proc_next: process (R_REGS, CHEX, CDP) variable r : regs_type := regs_init; variable n : regs_type := regs_init; variable cano : slv((2**DCWIDTH)-1 downto 0) := (others=>'0'); begin r := R_REGS; n := R_REGS; n.cdiv := slv(unsigned(r.cdiv) - 1); if unsigned(r.cdiv) = 0 then n.dcnt := slv(unsigned(r.dcnt) + 1); end if; -- the logic below ensures that the anode PNP driver transistor is switched -- off in the last quarter of the digit cycle.This prevents 'cross talk' -- between digits due to transistor turn off delays. -- For a nexys2 board at 50 MHz observed: -- no or 4 cycles gap well visible cross talk -- with 8 cycles still some weak cross talk -- with 16 cycles none is visible. -- --> The turn-off delay of the anode driver PNP's this therefore -- larger 160 ns and below 320 ns. -- As consquence CDWIDTH should be at least 6 for 50 MHz and 7 for 100 MHz. cano := (others=>'1'); if r.cdiv(CDWIDTH-1 downto CDWIDTH-2) /= "00" then cano(to_integer(unsigned(r.dcnt))) := '0'; end if; N_REGS <= n; ANO_N <= cano; SEG_N <= not (CDP & hex2segtbl(to_integer(unsigned(CHEX)))); end process proc_next; proc_mux: process (R_REGS, DIN, DP) begin CDP <= DP(to_integer(unsigned(R_REGS.dcnt))); CHEX(0) <= DIN(0+4*to_integer(unsigned(R_REGS.dcnt))); CHEX(1) <= DIN(1+4*to_integer(unsigned(R_REGS.dcnt))); CHEX(2) <= DIN(2+4*to_integer(unsigned(R_REGS.dcnt))); CHEX(3) <= DIN(3+4*to_integer(unsigned(R_REGS.dcnt))); end process proc_mux; end syn;
Go to most recent revision | Compare with Previous | Blame | View Log