URL
https://opencores.org/ocsvn/w11/w11/trunk
Subversion Repositories w11
[/] [w11/] [tags/] [w11a_V0.74/] [rtl/] [sys_gen/] [tst_serloop/] [tst_serloop_hiomap.vhd] - Rev 36
Go to most recent revision | Compare with Previous | Blame | View Log
-- $Id: tst_serloop_hiomap.vhd 751 2016-03-25 19:46:11Z mueller $ -- -- Copyright 2011- by Walter F.J. Mueller <W.F.J.Mueller@gsi.de> -- -- This program is free software; you may redistribute and/or modify it under -- the terms of the GNU General Public License as published by the Free -- Software Foundation, either version 2, or at your option any later version. -- -- This program is distributed in the hope that it will be useful, but -- WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY -- or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License -- for complete details. -- ------------------------------------------------------------------------------ -- Module Name: tst_serloop_hiomap - syn -- Description: default human I/O mapper -- -- Dependencies: - -- Test bench: - -- -- Target Devices: generic -- Tool versions: ise 13.1-14.7; viv 2014.4-2015.4; ghdl 0.29-0.33 -- -- Revision History: -- Date Rev Version Comment -- 2011-12-09 437 1.0.2 rename serport stat->moni port -- 2011-11-16 426 1.0.1 setup leds and dps -- 2011-11-05 420 1.0 Initial version ------------------------------------------------------------------------------ -- -- Usage of Switches, Buttons, LEDs: -- -- BTN(3): -- unused -- -- (2): -- unused -- -- (1): load enables from SWI(7:4) -- SWI(7) -> ENAFTDI -- SWI(6) -> ENATHROTTLE -- SWI(5) -> ENAESC -- SWI(4) -> ENAXON -- (0): reset state [!! decoded by top level design !!] -- -- SWI(7:4) select display or enable pattern (when BTN(1) pressed) -- (3) -- unused -- -- (2:1): mode 00 idle -- 01 rxblast -- 10 txblast -- 11 loop -- SWI(0) 0 -> main board RS232 port -- 1 -> Pmod1 RS232 port -- -- LED(7) enaesc -- (6) enaxon -- (5) rxfecnt > 0 (frame error) -- (4) rxoecnt > 0 (overrun error) -- (3) rxsecnt > 0 (sequence error) -- (2) abact (shows ab activity) -- (1) (not rxok) or (not txok) (shows back preasure) -- (0) rxact or txact (shows activity) -- -- DSP data as selected by SWI(7:4) -- 0000 -> rxfecnt -- 0001 -> rxoecnt -- 0010 -> rxsecnt -- 0100 -> rxcnt.l -- 0101 -> rxcnt.h -- 0110 -> txcnt.l -- 0111 -> txcnt.h -- 1000 -> rxokcnt -- 1001 -> txokcnt -- 1010 -> rxuicnt,rxuidat -- 1111 -> abclkdiv -- -- DP(3): not SER_MONI.txok (shows tx back preasure) -- (2): SER_MONI.txact (shows tx activity) -- (1): not SER_MONI.rxok (shows rx back preasure) -- (0): SER_MONI.rxact (shows rx activity) -- library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; use work.slvtypes.all; use work.serportlib.all; use work.tst_serlooplib.all; -- ---------------------------------------------------------------------------- entity tst_serloop_hiomap is -- default human I/O mapper port ( CLK : in slbit; -- clock RESET : in slbit; -- reset HIO_CNTL : out hio_cntl_type; -- tester controls from hio HIO_STAT : in hio_stat_type; -- tester status to diaplay by hio SER_MONI : in serport_moni_type; -- serport monitor to display by hio SWI : in slv8; -- switch settings BTN : in slv4; -- button settings LED : out slv8; -- led data DSP_DAT : out slv16; -- display data DSP_DP : out slv4 -- display decimal points ); end tst_serloop_hiomap; architecture syn of tst_serloop_hiomap is type regs_type is record enaxon : slbit; -- enable xon/xoff handling enaesc : slbit; -- enable xon/xoff escaping enathrottle : slbit; -- enable 1 msec tx throttling enaftdi : slbit; -- enable ftdi flush handling dspdat : slv16; -- display data end record regs_type; constant regs_init : regs_type := ( '0','0','0','0', -- enaxon,enaesc,enathrottle,enaftdi (others=>'0') -- dspdat ); signal R_REGS : regs_type := regs_init; -- state registers signal N_REGS : regs_type := regs_init; -- next value state regs begin proc_regs: process (CLK) begin if rising_edge(CLK) then if RESET = '1' then R_REGS <= regs_init; else R_REGS <= N_REGS; end if; end if; end process proc_regs; proc_next: process (R_REGS, HIO_STAT, SER_MONI, SWI, BTN) variable r : regs_type := regs_init; variable n : regs_type := regs_init; variable icntl : hio_cntl_type := hio_cntl_init; variable iled : slv8 := (others=>'0'); variable idat : slv16 := (others=>'0'); variable idp : slv4 := (others=>'0'); begin r := R_REGS; n := R_REGS; icntl := hio_cntl_init; iled := (others=>'0'); idat := (others=>'0'); idp := (others=>'0'); -- handle BTN(1) "load enables" press if BTN(1) = '1' then n.enaxon := SWI(4); n.enaesc := SWI(5); n.enathrottle := SWI(6); n.enaftdi := SWI(7); end if; -- setup tester controls icntl.mode := SWI(2 downto 1); icntl.enaxon := r.enaxon; icntl.enaesc := r.enaesc; icntl.enathrottle := r.enathrottle; icntl.enaftdi := r.enaftdi; -- setup leds iled(7) := icntl.enaesc; iled(6) := icntl.enaxon; if unsigned(HIO_STAT.rxfecnt) > 0 then iled(5) := '1'; end if; if unsigned(HIO_STAT.rxoecnt) > 0 then iled(4) := '1'; end if; if unsigned(HIO_STAT.rxsecnt) > 0 then iled(3) := '1'; end if; iled(2) := SER_MONI.abact; iled(1) := (not SER_MONI.rxok) or (not SER_MONI.txok); iled(0) := SER_MONI.rxact or SER_MONI.txact; -- setup display data case SWI(7 downto 4) is when "0000" => idat := HIO_STAT.rxfecnt; when "0001" => idat := HIO_STAT.rxoecnt; when "0010" => idat := HIO_STAT.rxsecnt; when "0100" => idat := HIO_STAT.rxcnt(15 downto 0); when "0101" => idat := HIO_STAT.rxcnt(31 downto 16); when "0110" => idat := HIO_STAT.txcnt(15 downto 0); when "0111" => idat := HIO_STAT.txcnt(31 downto 16); when "1000" => idat := HIO_STAT.rxokcnt; when "1001" => idat := HIO_STAT.txokcnt; when "1010" => idat := HIO_STAT.rxuicnt & HIO_STAT.rxuidat; when "1111" => idat := SER_MONI.abclkdiv; when others => null; end case; n.dspdat := idat; -- setup display decimal points idp(3) := not SER_MONI.txok; -- tx back preasure idp(2) := SER_MONI.txact; -- tx activity idp(1) := not SER_MONI.rxok; -- rx back preasure idp(0) := SER_MONI.rxact; -- rx activity N_REGS <= n; HIO_CNTL <= icntl; LED <= iled; DSP_DAT <= r.dspdat; DSP_DP <= idp; end process proc_next; end syn;
Go to most recent revision | Compare with Previous | Blame | View Log