Subversion Repositories wbuart32

################################################################################
##
## Filename:    Makefile
##
## Project:     wbuart32, a full featured UART with simulator
##
## Purpose:     To test a group of Verilator modules: txuart (UART transmitter),
##              rxuart (UART receiver/sink) and wbuart (UART module, containing
##      both receiver and transmitter, with FIFOs, controlled via wishbone).
##
##
## Targets:
##      test
##              Perform both tests.  The end result should be either a PASS
##              or a FAIL.
##
##      helloworld
##              A non-automated, and less interactive test than the others.  In
##              this test, the UART simply produces a Hello World message to the
##              screen over and over again.
##
##      linetest
##              An automated test of both txuart and rxuart.  The test works
##              by sending a message through the rxuart, and receiving the
##              message via the txuart.  This depends upon a Verilog test
##              infrastructure, linetest.v.
##
##              This test may be ran in an interactive mode.  In this mode,
##              characters written to the UART will be reflected back upon
##              the entrance of a return character.
##
##      speechtest
##              An automated test of the wbuart, txuart, and fifo.  In this
##              case, the test RTL produces a copy of the Gettysburg address,
##              filling the FIFO at 12/16 at a time.  In automated mode, the
##              speechtest will compare the output against against a text copy
##              of the speech, and report upon any success or failure.
##
##              In interactive mode, the test will repeatedly print out the
##              Gettysburg address until stopped.  (It may take a significant
##              amount of time between copies of the Gettysburg address ...)
##
##
## Creator:     Dan Gisselquist, Ph.D.
##              Gisselquist Technology, LLC
##
################################################################################
##
## Copyright (C) 2015-2016, Gisselquist Technology, LLC
##
## This program is free software (firmware): you can redistribute it and/or
## modify it under the terms of  the GNU General Public License as published
## by the Free Software Foundation, either version 3 of the License, or (at
## your option) any later version.
##
## This program is distributed in the hope that it will be useful, but WITHOUT
## ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
## FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
## for more details.
##
## You should have received a copy of the GNU General Public License along
## with this program.  (It's in the $(ROOT)/doc directory, run make with no
## target there if the PDF file isn't present.)  If not, see
## <http://www.gnu.org/licenses/> for a copy.
##
## License:     GPL, v3, as defined and found on www.gnu.org,
##              http://www.gnu.org/licenses/gpl.html
##
##
################################################################################
##
##
CXX     := g++
FLAGS   := -Wall -Og -g
OBJDIR  := obj-pc
RTLD    := ../verilog
VERILATOR_ROOT ?= $(shell bash -c 'verilator -V|grep VERILATOR_ROOT | head -1 | sed -e " s/^.*=\s*//"')
VROOT   := $(VERILATOR_ROOT)
INCS    := -I$(RTLD)/obj_dir/ -I$(VROOT)/include
SOURCES := helloworld.cpp linetest.cpp uartsim.cpp uartsim.h
VOBJDR  := $(RTLD)/obj_dir
SYSVDR  := $(VROOT)/include
VSRC    := verilated.cpp verilated_vcd_c.cpp
VLIB    := $(addprefix $(OBJDIR)/,$(subst .cpp,.o,$(VSRC)))
# Sources necessary to build the linetest program (rxuart-txuart test)
LINSRCS := linetest.cpp uartsim.cpp
LINOBJ := $(subst .cpp,.o,$(LINSRCS))
LINOBJS:= $(addprefix $(OBJDIR)/,$(LINOBJ)) $(VLIB)
# Sources necessary to build the helloworld test (txuart test)
HLOSRCS := helloworld.cpp uartsim.cpp
HLOOBJ := $(subst .cpp,.o,$(HLOSRCS))
HLOOBJS:= $(addprefix $(OBJDIR)/,$(HLOOBJ)) $(VLIB)
# Sources necessary to build the speech test (wbuart test)
SPCHSRCS:= speechtest.cpp uartsim.cpp
SPCHOBJ := $(subst .cpp,.o,$(SPCHSRCS))
SPCHOBJS:= $(addprefix $(OBJDIR)/,$(SPCHOBJ)) $(VLIB)
all:    $(OBJDIR)/ linetest helloworld speechtest test

$(OBJDIR)/uartsim.o: uartsim.cpp uartsim.h

$(OBJDIR)/%.o: %.cpp
        $(mk-objdir)
        $(CXX) $(FLAGS) $(INCS) -c $< -o $@

$(OBJDIR)/%.o: $(SYSVDR)/%.cpp
        $(mk-objdir)
        $(CXX) $(FLAGS) $(INCS) -c $< -o $@

linetest: $(LINOBJS) $(VOBJDR)/Vlinetest__ALL.a
        $(CXX) $(FLAGS) $(INCS) $^ -o $@

helloworld: $(HLOOBJS) $(VOBJDR)/Vhelloworld__ALL.a
        $(CXX) $(FLAGS) $(INCS) $^ -o $@

#
# The speech test program depends upon a copy of the Gettysburg Address,
# turned into a hex file format which will be read by the Verilog/RTL
# $readmemh function.  However, we need to create that hex file that will 
# written.  That's the purpose of mkspeech--to make a file that can be read
# by $readmemh.
#
mkspeech: mkspeech.cpp
        $(CXX) mkspeech.cpp -o $@

# Now that mkspeech is available, use it to produce a speech.hex file from
# the speech.txt file.  Be careful if you adjust this speech: the speechfifo.v
# verilog file depends upon the exact number of characters--its not a portable
# dependency, but ... it is what it is.
speech.hex: mkspeech speech.txt
        ./mkspeech speech.txt
        bash -c "if [ -d ../verilog/ ]; then cp speech.hex ../verilog/; fi"

# Now, if the speech.hex file is available, then we can perform our final build.
# Actually, we could've done this without the speech file being available, but
# this works.
speechtest: speech.hex $(SPCHOBJS) $(VOBJDR)/Vspeechfifo__ALL.a 
        $(CXX) $(FLAGS) $(INCS) $(SPCHOBJS) $(VOBJDR)/Vspeechfifo__ALL.a -o $@

test: linetest speechtest
        ./linetest
        ./speechtest

#
# The "depends" target, to know what files things depend upon.  The depends
# file itself is kept in $(OBJDIR)/depends.txt
#
define  build-depends
        $(mk-objdir)
        @echo "Building dependency file"
        @$(CXX) $(CFLAGS) $(INCS) -MM $(SOURCES) > $(OBJDIR)/xdepends.txt
        @sed -e 's/^.*.o: /$(OBJDIR)\/&/' < $(OBJDIR)/xdepends.txt > $(OBJDIR)/depends.txt
        @rm $(OBJDIR)/xdepends.txt
endef

.PHONY: depends
depends: tags
        $(build-depends)

$(OBJDIR)/depends.txt: depends

#
define  mk-objdir
        @bash -c "if [ ! -e $(OBJDIR) ]; then mkdir -p $(OBJDIR); fi"
endef

#
# The "tags" target
#
tags:   $(SOURCES) $(HEADERS)
        @echo "Generating tags"
        @ctags $(SOURCES) $(HEADERS)

.PHONY: clean
clean:
        rm -f  ./linetest ./helloworld ./speechtest
        rm -f ./mkspeech ./speech.hex
        rm -rf $(OBJDIR)/

-include $(OBJDIR)/depends.txt