URL
https://opencores.org/ocsvn/xulalx25soc/xulalx25soc/trunk
Subversion Repositories xulalx25soc
[/] [xulalx25soc/] [trunk/] [rtl/] [wbuoutput.v] - Rev 37
Go to most recent revision | Compare with Previous | Blame | View Log
//////////////////////////////////////////////////////////////////////////////// // // Filename: wbuoutput.v // // Project: XuLA2 board // // Purpose: Converts 36-bit codewords into bytes to be placed on the serial // output port. The codewords themselves are the results of bus // transactions, which are then (hopefully) compressed within here and // carefully arranged into "lines" for visual viewing (if necessary). // // // Creator: Dan Gisselquist, Ph.D. // Gisselquist Technology, LLC // //////////////////////////////////////////////////////////////////////////////// // // Copyright (C) 2015, Gisselquist Technology, LLC // // This program is free software (firmware): you can redistribute it and/or // modify it under the terms of the GNU General Public License as published // by the Free Software Foundation, either version 3 of the License, or (at // your option) any later version. // // This program is distributed in the hope that it will be useful, but WITHOUT // ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or // FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License // for more details. // // License: GPL, v3, as defined and found on www.gnu.org, // http://www.gnu.org/licenses/gpl.html // // //////////////////////////////////////////////////////////////////////////////// // // module wbuoutput(i_clk, i_rst, i_stb, i_codword, i_wb_cyc, i_int, i_bus_busy, o_stb, o_char, i_tx_busy, o_fifo_err); input i_clk, i_rst; input i_stb; input [35:0] i_codword; // Not Idle indicators input i_wb_cyc, i_int, i_bus_busy; // Outputs to our UART transmitter output wire o_stb; output wire [7:0] o_char; // Miscellaneous I/O: UART transmitter busy, and fifo error input i_tx_busy; output wire o_fifo_err; wire fifo_rd, dw_busy, fifo_empty_n, fifo_err; wire [35:0] fifo_codword; wire cw_stb, cw_busy, cp_stb, dw_stb, ln_stb, ln_busy, cp_busy, byte_busy; wire [35:0] cw_codword, cp_word; wire [6:0] dw_bits, ln_bits; // `define SKIP_FIFO `ifdef SKIP_FIFO assign fifo_rd = i_stb; assign fifo_codword = i_codword; assign fifo_err = 1'b0; `else assign fifo_rd = (fifo_empty_n)&&(~cw_busy); wbufifo #(36,10) busoutfifo(i_clk, i_rst, i_stb, i_codword, fifo_rd, fifo_codword, fifo_empty_n, fifo_err); `endif assign o_fifo_err = fifo_err; wbuidleint buildcw(i_clk, fifo_rd, fifo_codword, i_wb_cyc, i_bus_busy, i_int, cw_stb, cw_codword, cw_busy, cp_busy); // assign o_dbg = dw_busy; // Always asserted ... ??? // assign o_dbg = { dw_busy, ln_busy, fifo_rd }; // Stuck: dw_busy and ln_busy get stuck high after read attempt, // fifo_rd is low // assign o_dbg = { fifo_rd, cp_stb, cw_stb }; // cw_stb and cp_stb get stuck high after one read // // cw_busy & cw_stb, not cp_stb, but dw_busy // // `define SKIP_COMPRESS `ifdef SKIP_COMPRESS assign cp_stb = cw_stb; assign cp_word = cw_codword; assign cp_busy = dw_busy; `else assign cp_busy = cp_stb; wbucompress packit(i_clk, cw_stb, cw_codword, cp_stb, cp_word, dw_busy); `endif wbudeword deword(i_clk, cp_stb, cp_word, ln_busy, dw_stb, dw_bits, dw_busy); wbucompactlines linepacker(i_clk, dw_stb, dw_bits, ln_stb, ln_bits, (i_wb_cyc||i_bus_busy||fifo_empty_n||cw_busy), byte_busy, ln_busy); wbusixchar mkbytes(i_clk, ln_stb, ln_bits, o_stb, o_char, byte_busy, i_tx_busy); endmodule
Go to most recent revision | Compare with Previous | Blame | View Log