OpenCores
URL https://opencores.org/ocsvn/openmsp430/openmsp430/trunk

Subversion Repositories openmsp430

[/] [openmsp430/] [trunk/] [core/] [rtl/] [verilog/] [openMSP430.v] - Rev 202

Compare with Previous | Blame | View Log

//----------------------------------------------------------------------------
// Copyright (C) 2009 , Olivier Girard
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//     * Redistributions of source code must retain the above copyright
//       notice, this list of conditions and the following disclaimer.
//     * Redistributions in binary form must reproduce the above copyright
//       notice, this list of conditions and the following disclaimer in the
//       documentation and/or other materials provided with the distribution.
//     * Neither the name of the authors nor the names of its contributors
//       may be used to endorse or promote products derived from this software
//       without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
// THE POSSIBILITY OF SUCH DAMAGE
//
//----------------------------------------------------------------------------
//
// *File Name: openMSP430.v
//
// *Module Description:
//                       openMSP430 Top level file
//
// *Author(s):
//              - Olivier Girard,    olgirard@gmail.com
//
//----------------------------------------------------------------------------
// $Rev: 202 $
// $LastChangedBy: olivier.girard $
// $LastChangedDate: 2015-07-01 23:13:32 +0200 (Wed, 01 Jul 2015) $
//----------------------------------------------------------------------------
`ifdef OMSP_NO_INCLUDE
`else
`include "openMSP430_defines.v"
`endif
 
module  openMSP430 (
 
// OUTPUTs
    aclk,                                    // ASIC ONLY: ACLK
    aclk_en,                                 // FPGA ONLY: ACLK enable
    dbg_freeze,                              // Freeze peripherals
    dbg_i2c_sda_out,                         // Debug interface: I2C SDA OUT
    dbg_uart_txd,                            // Debug interface: UART TXD
    dco_enable,                              // ASIC ONLY: Fast oscillator enable
    dco_wkup,                                // ASIC ONLY: Fast oscillator wake-up (asynchronous)
    dmem_addr,                               // Data Memory address
    dmem_cen,                                // Data Memory chip enable (low active)
    dmem_din,                                // Data Memory data input
    dmem_wen,                                // Data Memory write byte enable (low active)
    irq_acc,                                 // Interrupt request accepted (one-hot signal)
    lfxt_enable,                             // ASIC ONLY: Low frequency oscillator enable
    lfxt_wkup,                               // ASIC ONLY: Low frequency oscillator wake-up (asynchronous)
    mclk,                                    // Main system clock
    dma_dout,                                // Direct Memory Access data output
    dma_ready,                               // Direct Memory Access is complete
    dma_resp,                                // Direct Memory Access response (0:Okay / 1:Error)
    per_addr,                                // Peripheral address
    per_din,                                 // Peripheral data input
    per_en,                                  // Peripheral enable (high active)
    per_we,                                  // Peripheral write byte enable (high active)
    pmem_addr,                               // Program Memory address
    pmem_cen,                                // Program Memory chip enable (low active)
    pmem_din,                                // Program Memory data input (optional)
    pmem_wen,                                // Program Memory write byte enable (low active) (optional)
    puc_rst,                                 // Main system reset
    smclk,                                   // ASIC ONLY: SMCLK
    smclk_en,                                // FPGA ONLY: SMCLK enable
 
// INPUTs
    cpu_en,                                  // Enable CPU code execution (asynchronous and non-glitchy)
    dbg_en,                                  // Debug interface enable (asynchronous and non-glitchy)
    dbg_i2c_addr,                            // Debug interface: I2C Address
    dbg_i2c_broadcast,                       // Debug interface: I2C Broadcast Address (for multicore systems)
    dbg_i2c_scl,                             // Debug interface: I2C SCL
    dbg_i2c_sda_in,                          // Debug interface: I2C SDA IN
    dbg_uart_rxd,                            // Debug interface: UART RXD (asynchronous)
    dco_clk,                                 // Fast oscillator (fast clock)
    dmem_dout,                               // Data Memory data output
    irq,                                     // Maskable interrupts
    lfxt_clk,                                // Low frequency oscillator (typ 32kHz)
    dma_addr,                                // Direct Memory Access address
    dma_din,                                 // Direct Memory Access data input
    dma_en,                                  // Direct Memory Access enable (high active)
    dma_priority,                            // Direct Memory Access priority (0:low / 1:high)
    dma_we,                                  // Direct Memory Access write byte enable (high active)
    dma_wkup,                                // ASIC ONLY: DMA Sub-System Wake-up (asynchronous and non-glitchy)
    nmi,                                     // Non-maskable interrupt (asynchronous)
    per_dout,                                // Peripheral data output
    pmem_dout,                               // Program Memory data output
    reset_n,                                 // Reset Pin (low active, asynchronous and non-glitchy)
    scan_enable,                             // ASIC ONLY: Scan enable (active during scan shifting)
    scan_mode,                               // ASIC ONLY: Scan mode
    wkup                                     // ASIC ONLY: System Wake-up (asynchronous and non-glitchy)
);
 
// PARAMETERs
//============
parameter            INST_NR  = 8'h00;       // Current oMSP instance number     (for multicore systems)
parameter            TOTAL_NR = 8'h00;       // Total number of oMSP instances-1 (for multicore systems)
 
// OUTPUTs
//============
output               aclk;                   // ASIC ONLY: ACLK
output               aclk_en;                // FPGA ONLY: ACLK enable
output               dbg_freeze;             // Freeze peripherals
output               dbg_i2c_sda_out;        // Debug interface: I2C SDA OUT
output               dbg_uart_txd;           // Debug interface: UART TXD
output               dco_enable;             // ASIC ONLY: Fast oscillator enable
output               dco_wkup;               // ASIC ONLY: Fast oscillator wake-up (asynchronous)
output [`DMEM_MSB:0] dmem_addr;              // Data Memory address
output               dmem_cen;               // Data Memory chip enable (low active)
output        [15:0] dmem_din;               // Data Memory data input
output         [1:0] dmem_wen;               // Data Memory write byte enable (low active)
output [`IRQ_NR-3:0] irq_acc;                // Interrupt request accepted (one-hot signal)
output               lfxt_enable;            // ASIC ONLY: Low frequency oscillator enable
output               lfxt_wkup;              // ASIC ONLY: Low frequency oscillator wake-up (asynchronous)
output               mclk;                   // Main system clock
output        [15:0] dma_dout;               // Direct Memory Access data output
output               dma_ready;              // Direct Memory Access is complete
output               dma_resp;               // Direct Memory Access response (0:Okay / 1:Error)
output        [13:0] per_addr;               // Peripheral address
output        [15:0] per_din;                // Peripheral data input
output               per_en;                 // Peripheral enable (high active)
output         [1:0] per_we;                 // Peripheral write byte enable (high active)
output [`PMEM_MSB:0] pmem_addr;              // Program Memory address
output               pmem_cen;               // Program Memory chip enable (low active)
output        [15:0] pmem_din;               // Program Memory data input (optional)
output         [1:0] pmem_wen;               // Program Memory write enable (low active) (optional)
output               puc_rst;                // Main system reset
output               smclk;                  // ASIC ONLY: SMCLK
output               smclk_en;               // FPGA ONLY: SMCLK enable
 
 
// INPUTs
//============
input                cpu_en;                 // Enable CPU code execution (asynchronous and non-glitchy)
input                dbg_en;                 // Debug interface enable (asynchronous and non-glitchy)
input          [6:0] dbg_i2c_addr;           // Debug interface: I2C Address
input          [6:0] dbg_i2c_broadcast;      // Debug interface: I2C Broadcast Address (for multicore systems)
input                dbg_i2c_scl;            // Debug interface: I2C SCL
input                dbg_i2c_sda_in;         // Debug interface: I2C SDA IN
input                dbg_uart_rxd;           // Debug interface: UART RXD (asynchronous)
input                dco_clk;                // Fast oscillator (fast clock)
input         [15:0] dmem_dout;              // Data Memory data output
input  [`IRQ_NR-3:0] irq;                    // Maskable interrupts (14, 30 or 62)
input                lfxt_clk;               // Low frequency oscillator (typ 32kHz)
input         [15:1] dma_addr;               // Direct Memory Access address
input         [15:0] dma_din;                // Direct Memory Access data input
input                dma_en;                 // Direct Memory Access enable (high active)
input                dma_priority;           // Direct Memory Access priority (0:low / 1:high)
input          [1:0] dma_we;                 // Direct Memory Access write byte enable (high active)
input                dma_wkup;               // ASIC ONLY: DMA Wake-up (asynchronous and non-glitchy)
input                nmi;                    // Non-maskable interrupt (asynchronous and non-glitchy)
input         [15:0] per_dout;               // Peripheral data output
input         [15:0] pmem_dout;              // Program Memory data output
input                reset_n;                // Reset Pin (active low, asynchronous and non-glitchy)
input                scan_enable;            // ASIC ONLY: Scan enable (active during scan shifting)
input                scan_mode;              // ASIC ONLY: Scan mode
input                wkup;                   // ASIC ONLY: System Wake-up (asynchronous and non-glitchy)
 
 
 
//=============================================================================
// 1)  INTERNAL WIRES/REGISTERS/PARAMETERS DECLARATION
//=============================================================================
 
wire           [7:0] inst_ad;
wire           [7:0] inst_as;
wire          [11:0] inst_alu;
wire                 inst_bw;
wire                 inst_irq_rst;
wire                 inst_mov;
wire          [15:0] inst_dest;
wire          [15:0] inst_dext;
wire          [15:0] inst_sext;
wire           [7:0] inst_so;
wire          [15:0] inst_src;
wire           [2:0] inst_type;
wire           [7:0] inst_jmp;
wire           [3:0] e_state;
wire                 exec_done;
wire                 decode_noirq;
wire                 cpu_en_s;
wire                 cpuoff;
wire                 oscoff;
wire                 scg0;
wire                 scg1;
wire                 por;
wire                 gie;
wire                 cpu_mclk;
wire                 dma_mclk;
wire                 mclk_dma_enable;
wire                 mclk_dma_wkup;
wire                 mclk_enable;
wire                 mclk_wkup;
wire          [31:0] cpu_id;
wire           [7:0] cpu_nr_inst  = INST_NR;
wire           [7:0] cpu_nr_total = TOTAL_NR;
 
wire          [15:0] eu_mab;
wire          [15:0] eu_mdb_in;
wire          [15:0] eu_mdb_out;
wire           [1:0] eu_mb_wr;
wire                 eu_mb_en;
wire          [15:0] fe_mab;
wire          [15:0] fe_mdb_in;
wire                 fe_mb_en;
wire                 fe_pmem_wait;
 
wire                 pc_sw_wr;
wire          [15:0] pc_sw;
wire          [15:0] pc;
wire          [15:0] pc_nxt;
 
wire                 nmi_acc;
wire                 nmi_pnd;
wire                 nmi_wkup;
 
wire                 wdtie;
wire                 wdtnmies;
wire                 wdtifg;
wire                 wdt_irq;
wire                 wdt_wkup;
wire                 wdt_reset;
wire                 wdtifg_sw_clr;
wire                 wdtifg_sw_set;
 
wire                 dbg_clk;
wire                 dbg_rst;
wire                 dbg_en_s;
wire                 dbg_halt_cmd;
wire                 dbg_mem_en;
wire                 dbg_reg_wr;
wire                 dbg_cpu_reset;
wire          [15:0] dbg_mem_addr;
wire          [15:0] dbg_mem_dout;
wire          [15:0] dbg_mem_din;
wire          [15:0] dbg_reg_din;
wire           [1:0] dbg_mem_wr;
 
wire                 cpu_halt_st;
wire                 cpu_halt_cmd;
wire                 puc_pnd_set;
 
wire          [15:0] per_dout_or;
wire          [15:0] per_dout_sfr;
wire          [15:0] per_dout_wdog;
wire          [15:0] per_dout_mpy;
wire          [15:0] per_dout_clk;
 
 
//=============================================================================
// 2)  GLOBAL CLOCK & RESET MANAGEMENT
//=============================================================================
 
omsp_clock_module clock_module_0 (
 
// OUTPUTs
    .aclk              (aclk),               // ACLK
    .aclk_en           (aclk_en),            // ACLK enablex
    .cpu_en_s          (cpu_en_s),           // Enable CPU code execution (synchronous)
    .cpu_mclk          (cpu_mclk),           // Main system CPU only clock
    .dma_mclk          (dma_mclk),           // Main system DMA and/or CPU clock
    .dbg_clk           (dbg_clk),            // Debug unit clock
    .dbg_en_s          (dbg_en_s),           // Debug interface enable (synchronous)
    .dbg_rst           (dbg_rst),            // Debug unit reset
    .dco_enable        (dco_enable),         // Fast oscillator enable
    .dco_wkup          (dco_wkup),           // Fast oscillator wake-up (asynchronous)
    .lfxt_enable       (lfxt_enable),        // Low frequency oscillator enable
    .lfxt_wkup         (lfxt_wkup),          // Low frequency oscillator wake-up (asynchronous)
    .per_dout          (per_dout_clk),       // Peripheral data output
    .por               (por),                // Power-on reset
    .puc_pnd_set       (puc_pnd_set),        // PUC pending set for the serial debug interface
    .puc_rst           (puc_rst),            // Main system reset
    .smclk             (smclk),              // SMCLK
    .smclk_en          (smclk_en),           // SMCLK enable
 
// INPUTs
    .cpu_en            (cpu_en),             // Enable CPU code execution (asynchronous)
    .cpuoff            (cpuoff),             // Turns off the CPU
    .dbg_cpu_reset     (dbg_cpu_reset),      // Reset CPU from debug interface
    .dbg_en            (dbg_en),             // Debug interface enable (asynchronous)
    .dco_clk           (dco_clk),            // Fast oscillator (fast clock)
    .lfxt_clk          (lfxt_clk),           // Low frequency oscillator (typ 32kHz)
    .mclk_dma_enable   (mclk_dma_enable),    // DMA Sub-System Clock enable
    .mclk_dma_wkup     (mclk_dma_wkup),      // DMA Sub-System Clock wake-up (asynchronous)
    .mclk_enable       (mclk_enable),        // Main System Clock enable
    .mclk_wkup         (mclk_wkup),          // Main System Clock wake-up (asynchronous)
    .oscoff            (oscoff),             // Turns off LFXT1 clock input
    .per_addr          (per_addr),           // Peripheral address
    .per_din           (per_din),            // Peripheral data input
    .per_en            (per_en),             // Peripheral enable (high active)
    .per_we            (per_we),             // Peripheral write enable (high active)
    .reset_n           (reset_n),            // Reset Pin (low active, asynchronous)
    .scan_enable       (scan_enable),        // Scan enable (active during scan shifting)
    .scan_mode         (scan_mode),          // Scan mode
    .scg0              (scg0),               // System clock generator 1. Turns off the DCO
    .scg1              (scg1),               // System clock generator 1. Turns off the SMCLK
    .wdt_reset         (wdt_reset)           // Watchdog-timer reset
);
 
assign mclk = dma_mclk;
 
 
//=============================================================================
// 3)  FRONTEND (<=> FETCH & DECODE)
//=============================================================================
 
omsp_frontend frontend_0 (
 
// OUTPUTs
    .cpu_halt_st       (cpu_halt_st),        // Halt/Run status from CPU
    .decode_noirq      (decode_noirq),       // Frontend decode instruction
    .e_state           (e_state),            // Execution state
    .exec_done         (exec_done),          // Execution completed
    .inst_ad           (inst_ad),            // Decoded Inst: destination addressing mode
    .inst_as           (inst_as),            // Decoded Inst: source addressing mode
    .inst_alu          (inst_alu),           // ALU control signals
    .inst_bw           (inst_bw),            // Decoded Inst: byte width
    .inst_dest         (inst_dest),          // Decoded Inst: destination (one hot)
    .inst_dext         (inst_dext),          // Decoded Inst: destination extended instruction word
    .inst_irq_rst      (inst_irq_rst),       // Decoded Inst: Reset interrupt
    .inst_jmp          (inst_jmp),           // Decoded Inst: Conditional jump
    .inst_mov          (inst_mov),           // Decoded Inst: mov instruction
    .inst_sext         (inst_sext),          // Decoded Inst: source extended instruction word
    .inst_so           (inst_so),            // Decoded Inst: Single-operand arithmetic
    .inst_src          (inst_src),           // Decoded Inst: source (one hot)
    .inst_type         (inst_type),          // Decoded Instruction type
    .irq_acc           (irq_acc),            // Interrupt request accepted
    .mab               (fe_mab),             // Frontend Memory address bus
    .mb_en             (fe_mb_en),           // Frontend Memory bus enable
    .mclk_dma_enable   (mclk_dma_enable),    // DMA Sub-System Clock enable
    .mclk_dma_wkup     (mclk_dma_wkup),      // DMA Sub-System Clock wake-up (asynchronous)
    .mclk_enable       (mclk_enable),        // Main System Clock enable
    .mclk_wkup         (mclk_wkup),          // Main System Clock wake-up (asynchronous)
    .nmi_acc           (nmi_acc),            // Non-Maskable interrupt request accepted
    .pc                (pc),                 // Program counter
    .pc_nxt            (pc_nxt),             // Next PC value (for CALL & IRQ)
 
// INPUTs
    .cpu_en_s          (cpu_en_s),           // Enable CPU code execution (synchronous)
    .cpu_halt_cmd      (cpu_halt_cmd),       // Halt CPU command
    .cpuoff            (cpuoff),             // Turns off the CPU
    .dbg_reg_sel       (dbg_mem_addr[3:0]),  // Debug selected register for rd/wr access
    .dma_en            (dma_en),             // Direct Memory Access enable (high active)
    .dma_wkup          (dma_wkup),           // DMA Sub-System Wake-up (asynchronous and non-glitchy)
    .fe_pmem_wait      (fe_pmem_wait),       // Frontend wait for Instruction fetch
    .gie               (gie),                // General interrupt enable
    .irq               (irq),                // Maskable interrupts
    .mclk              (cpu_mclk),           // Main system clock
    .mdb_in            (fe_mdb_in),          // Frontend Memory data bus input
    .nmi_pnd           (nmi_pnd),            // Non-maskable interrupt pending
    .nmi_wkup          (nmi_wkup),           // NMI Wakeup
    .pc_sw             (pc_sw),              // Program counter software value
    .pc_sw_wr          (pc_sw_wr),           // Program counter software write
    .puc_rst           (puc_rst),            // Main system reset
    .scan_enable       (scan_enable),        // Scan enable (active during scan shifting)
    .wdt_irq           (wdt_irq),            // Watchdog-timer interrupt
    .wdt_wkup          (wdt_wkup),           // Watchdog Wakeup
    .wkup              (wkup)                // System Wake-up (asynchronous)
);
 
 
//=============================================================================
// 4)  EXECUTION UNIT
//=============================================================================
 
omsp_execution_unit execution_unit_0 (
 
// OUTPUTs
    .cpuoff            (cpuoff),             // Turns off the CPU
    .dbg_reg_din       (dbg_reg_din),        // Debug unit CPU register data input
    .mab               (eu_mab),             // Memory address bus
    .mb_en             (eu_mb_en),           // Memory bus enable
    .mb_wr             (eu_mb_wr),           // Memory bus write transfer
    .mdb_out           (eu_mdb_out),         // Memory data bus output
    .oscoff            (oscoff),             // Turns off LFXT1 clock input
    .pc_sw             (pc_sw),              // Program counter software value
    .pc_sw_wr          (pc_sw_wr),           // Program counter software write
    .scg0              (scg0),               // System clock generator 1. Turns off the DCO
    .scg1              (scg1),               // System clock generator 1. Turns off the SMCLK
 
// INPUTs
    .dbg_halt_st       (cpu_halt_st),        // Halt/Run status from CPU
    .dbg_mem_dout      (dbg_mem_dout),       // Debug unit data output
    .dbg_reg_wr        (dbg_reg_wr),         // Debug unit CPU register write
    .e_state           (e_state),            // Execution state
    .exec_done         (exec_done),          // Execution completed
    .gie               (gie),                // General interrupt enable
    .inst_ad           (inst_ad),            // Decoded Inst: destination addressing mode
    .inst_as           (inst_as),            // Decoded Inst: source addressing mode
    .inst_alu          (inst_alu),           // ALU control signals
    .inst_bw           (inst_bw),            // Decoded Inst: byte width
    .inst_dest         (inst_dest),          // Decoded Inst: destination (one hot)
    .inst_dext         (inst_dext),          // Decoded Inst: destination extended instruction word
    .inst_irq_rst      (inst_irq_rst),       // Decoded Inst: reset interrupt
    .inst_jmp          (inst_jmp),           // Decoded Inst: Conditional jump
    .inst_mov          (inst_mov),           // Decoded Inst: mov instruction
    .inst_sext         (inst_sext),          // Decoded Inst: source extended instruction word
    .inst_so           (inst_so),            // Decoded Inst: Single-operand arithmetic
    .inst_src          (inst_src),           // Decoded Inst: source (one hot)
    .inst_type         (inst_type),          // Decoded Instruction type
    .mclk              (cpu_mclk),           // Main system clock
    .mdb_in            (eu_mdb_in),          // Memory data bus input
    .pc                (pc),                 // Program counter
    .pc_nxt            (pc_nxt),             // Next PC value (for CALL & IRQ)
    .puc_rst           (puc_rst),            // Main system reset
    .scan_enable       (scan_enable)         // Scan enable (active during scan shifting)
);
 
 
//=============================================================================
// 5)  MEMORY BACKBONE
//=============================================================================
 
omsp_mem_backbone mem_backbone_0 (
 
// OUTPUTs
    .cpu_halt_cmd      (cpu_halt_cmd),       // Halt CPU command
    .dbg_mem_din       (dbg_mem_din),        // Debug unit Memory data input
    .dmem_addr         (dmem_addr),          // Data Memory address
    .dmem_cen          (dmem_cen),           // Data Memory chip enable (low active)
    .dmem_din          (dmem_din),           // Data Memory data input
    .dmem_wen          (dmem_wen),           // Data Memory write enable (low active)
    .eu_mdb_in         (eu_mdb_in),          // Execution Unit Memory data bus input
    .fe_mdb_in         (fe_mdb_in),          // Frontend Memory data bus input
    .fe_pmem_wait      (fe_pmem_wait),       // Frontend wait for Instruction fetch
    .dma_dout          (dma_dout),           // Direct Memory Access data output
    .dma_ready         (dma_ready),          // Direct Memory Access is complete
    .dma_resp          (dma_resp),           // Direct Memory Access response (0:Okay / 1:Error)
    .per_addr          (per_addr),           // Peripheral address
    .per_din           (per_din),            // Peripheral data input
    .per_we            (per_we),             // Peripheral write enable (high active)
    .per_en            (per_en),             // Peripheral enable (high active)
    .pmem_addr         (pmem_addr),          // Program Memory address
    .pmem_cen          (pmem_cen),           // Program Memory chip enable (low active)
    .pmem_din          (pmem_din),           // Program Memory data input (optional)
    .pmem_wen          (pmem_wen),           // Program Memory write enable (low active) (optional)
 
// INPUTs
    .cpu_halt_st       (cpu_halt_st),        // Halt/Run status from CPU
    .dbg_halt_cmd      (dbg_halt_cmd),       // Debug interface Halt CPU command
    .dbg_mem_addr      (dbg_mem_addr[15:1]), // Debug address for rd/wr access
    .dbg_mem_dout      (dbg_mem_dout),       // Debug unit data output
    .dbg_mem_en        (dbg_mem_en),         // Debug unit memory enable
    .dbg_mem_wr        (dbg_mem_wr),         // Debug unit memory write
    .dmem_dout         (dmem_dout),          // Data Memory data output
    .eu_mab            (eu_mab[15:1]),       // Execution Unit Memory address bus
    .eu_mb_en          (eu_mb_en),           // Execution Unit Memory bus enable
    .eu_mb_wr          (eu_mb_wr),           // Execution Unit Memory bus write transfer
    .eu_mdb_out        (eu_mdb_out),         // Execution Unit Memory data bus output
    .fe_mab            (fe_mab[15:1]),       // Frontend Memory address bus
    .fe_mb_en          (fe_mb_en),           // Frontend Memory bus enable
    .mclk              (dma_mclk),           // Main system clock
    .dma_addr          (dma_addr),           // Direct Memory Access address
    .dma_din           (dma_din),            // Direct Memory Access data input
    .dma_en            (dma_en),             // Direct Memory Access enable (high active)
    .dma_priority      (dma_priority),       // Direct Memory Access priority (0:low / 1:high)
    .dma_we            (dma_we),             // Direct Memory Access write byte enable (high active)
    .per_dout          (per_dout_or),        // Peripheral data output
    .pmem_dout         (pmem_dout),          // Program Memory data output
    .puc_rst           (puc_rst),            // Main system reset
    .scan_enable       (scan_enable)         // Scan enable (active during scan shifting)
);
 
wire UNUSED_fe_mab_0 = fe_mab[0];
 
//=============================================================================
// 6)  SPECIAL FUNCTION REGISTERS
//=============================================================================
omsp_sfr sfr_0 (
 
// OUTPUTs
    .cpu_id            (cpu_id),             // CPU ID
    .nmi_pnd           (nmi_pnd),            // NMI Pending
    .nmi_wkup          (nmi_wkup),           // NMI Wakeup
    .per_dout          (per_dout_sfr),       // Peripheral data output
    .wdtie             (wdtie),              // Watchdog-timer interrupt enable
    .wdtifg_sw_clr     (wdtifg_sw_clr),      // Watchdog-timer interrupt flag software clear
    .wdtifg_sw_set     (wdtifg_sw_set),      // Watchdog-timer interrupt flag software set
 
// INPUTs
    .cpu_nr_inst       (cpu_nr_inst),        // Current oMSP instance number
    .cpu_nr_total      (cpu_nr_total),       // Total number of oMSP instances-1
    .mclk              (dma_mclk),           // Main system clock
    .nmi               (nmi),                // Non-maskable interrupt (asynchronous)
    .nmi_acc           (nmi_acc),            // Non-Maskable interrupt request accepted
    .per_addr          (per_addr),           // Peripheral address
    .per_din           (per_din),            // Peripheral data input
    .per_en            (per_en),             // Peripheral enable (high active)
    .per_we            (per_we),             // Peripheral write enable (high active)
    .puc_rst           (puc_rst),            // Main system reset
    .scan_mode         (scan_mode),          // Scan mode
    .wdtifg            (wdtifg),             // Watchdog-timer interrupt flag
    .wdtnmies          (wdtnmies)            // Watchdog-timer NMI edge selection
);
 
 
//=============================================================================
// 7)  WATCHDOG TIMER
//=============================================================================
`ifdef WATCHDOG
omsp_watchdog watchdog_0 (
 
// OUTPUTs
    .per_dout          (per_dout_wdog),      // Peripheral data output
    .wdt_irq           (wdt_irq),            // Watchdog-timer interrupt
    .wdt_reset         (wdt_reset),          // Watchdog-timer reset
    .wdt_wkup          (wdt_wkup),           // Watchdog Wakeup
    .wdtifg            (wdtifg),             // Watchdog-timer interrupt flag
    .wdtnmies          (wdtnmies),           // Watchdog-timer NMI edge selection
 
// INPUTs
    .aclk              (aclk),               // ACLK
    .aclk_en           (aclk_en),            // ACLK enable
    .dbg_freeze        (dbg_freeze),         // Freeze Watchdog counter
    .mclk              (dma_mclk),           // Main system clock
    .per_addr          (per_addr),           // Peripheral address
    .per_din           (per_din),            // Peripheral data input
    .per_en            (per_en),             // Peripheral enable (high active)
    .per_we            (per_we),             // Peripheral write enable (high active)
    .por               (por),                // Power-on reset
    .puc_rst           (puc_rst),            // Main system reset
    .scan_enable       (scan_enable),        // Scan enable (active during scan shifting)
    .scan_mode         (scan_mode),          // Scan mode
    .smclk             (smclk),              // SMCLK
    .smclk_en          (smclk_en),           // SMCLK enable
    .wdtie             (wdtie),              // Watchdog-timer interrupt enable
    .wdtifg_irq_clr    (irq_acc[`IRQ_NR-6]), // Clear Watchdog-timer interrupt flag
    .wdtifg_sw_clr     (wdtifg_sw_clr),      // Watchdog-timer interrupt flag software clear
    .wdtifg_sw_set     (wdtifg_sw_set)       // Watchdog-timer interrupt flag software set
);
`else
assign per_dout_wdog        = 16'h0000;
assign wdt_irq              =  1'b0;
assign wdt_reset            =  1'b0;
assign wdt_wkup             =  1'b0;
assign wdtifg               =  1'b0;
assign wdtnmies             =  1'b0;
wire   UNUSED_por           =  por;
wire   UNUSED_wdtie         =  wdtie;
wire   UNUSED_wdtifg_sw_clr =  wdtifg_sw_clr;
wire   UNUSED_wdtifg_sw_set =  wdtifg_sw_set;
`endif
 
 
//=============================================================================
// 8)  HARDWARE MULTIPLIER
//=============================================================================
`ifdef MULTIPLIER
omsp_multiplier multiplier_0 (
 
// OUTPUTs
    .per_dout          (per_dout_mpy),       // Peripheral data output
 
// INPUTs
    .mclk              (dma_mclk),           // Main system clock
    .per_addr          (per_addr),           // Peripheral address
    .per_din           (per_din),            // Peripheral data input
    .per_en            (per_en),             // Peripheral enable (high active)
    .per_we            (per_we),             // Peripheral write enable (high active)
    .puc_rst           (puc_rst),            // Main system reset
    .scan_enable       (scan_enable)         // Scan enable (active during scan shifting)
);
`else
assign per_dout_mpy = 16'h0000;
`endif
 
//=============================================================================
// 9)  PERIPHERALS' OUTPUT BUS
//=============================================================================
 
assign  per_dout_or  =  per_dout      |
                        per_dout_clk  |
                        per_dout_sfr  |
                        per_dout_wdog |
                        per_dout_mpy;
 
 
//=============================================================================
// 10)  DEBUG INTERFACE
//=============================================================================
 
`ifdef DBG_EN
omsp_dbg dbg_0 (
 
// OUTPUTs
    .dbg_cpu_reset     (dbg_cpu_reset),      // Reset CPU from debug interface
    .dbg_freeze        (dbg_freeze),         // Freeze peripherals
    .dbg_halt_cmd      (dbg_halt_cmd),       // Halt CPU command
    .dbg_i2c_sda_out   (dbg_i2c_sda_out),    // Debug interface: I2C SDA OUT
    .dbg_mem_addr      (dbg_mem_addr),       // Debug address for rd/wr access
    .dbg_mem_dout      (dbg_mem_dout),       // Debug unit data output
    .dbg_mem_en        (dbg_mem_en),         // Debug unit memory enable
    .dbg_mem_wr        (dbg_mem_wr),         // Debug unit memory write
    .dbg_reg_wr        (dbg_reg_wr),         // Debug unit CPU register write
    .dbg_uart_txd      (dbg_uart_txd),       // Debug interface: UART TXD
 
// INPUTs
    .cpu_en_s          (cpu_en_s),           // Enable CPU code execution (synchronous)
    .cpu_id            (cpu_id),             // CPU ID
    .cpu_nr_inst       (cpu_nr_inst),        // Current oMSP instance number
    .cpu_nr_total      (cpu_nr_total),       // Total number of oMSP instances-1
    .dbg_clk           (dbg_clk),            // Debug unit clock
    .dbg_en_s          (dbg_en_s),           // Debug interface enable (synchronous)
    .dbg_halt_st       (cpu_halt_st),        // Halt/Run status from CPU
    .dbg_i2c_addr      (dbg_i2c_addr),       // Debug interface: I2C Address
    .dbg_i2c_broadcast (dbg_i2c_broadcast),  // Debug interface: I2C Broadcast Address (for multicore systems)
    .dbg_i2c_scl       (dbg_i2c_scl),        // Debug interface: I2C SCL
    .dbg_i2c_sda_in    (dbg_i2c_sda_in),     // Debug interface: I2C SDA IN
    .dbg_mem_din       (dbg_mem_din),        // Debug unit Memory data input
    .dbg_reg_din       (dbg_reg_din),        // Debug unit CPU register data input
    .dbg_rst           (dbg_rst),            // Debug unit reset
    .dbg_uart_rxd      (dbg_uart_rxd),       // Debug interface: UART RXD (asynchronous)
    .decode_noirq      (decode_noirq),       // Frontend decode instruction
    .eu_mab            (eu_mab),             // Execution-Unit Memory address bus
    .eu_mb_en          (eu_mb_en),           // Execution-Unit Memory bus enable
    .eu_mb_wr          (eu_mb_wr),           // Execution-Unit Memory bus write transfer
    .fe_mdb_in         (fe_mdb_in),          // Frontend Memory data bus input
    .pc                (pc),                 // Program counter
    .puc_pnd_set       (puc_pnd_set)         // PUC pending set for the serial debug interface
);
 
`else
assign      dbg_cpu_reset            =  1'b0;
assign      dbg_freeze               =  ~cpu_en_s;
assign      dbg_halt_cmd             =  1'b0;
assign      dbg_i2c_sda_out          =  1'b1;
assign      dbg_mem_addr             = 16'h0000;
assign      dbg_mem_dout             = 16'h0000;
assign      dbg_mem_en               =  1'b0;
assign      dbg_mem_wr               =  2'b00;
assign      dbg_reg_wr               =  1'b0;
assign      dbg_uart_txd             =  1'b1;
wire        UNUSED_decode_noirq      = decode_noirq;
wire [31:0] UNUSED_cpu_id            = cpu_id;
wire        UNUSED_eu_mab_0          = eu_mab[0];
wire        UNUSED_dbg_clk           = dbg_clk;
wire        UNUSED_dbg_rst           = dbg_rst;
wire        UNUSED_dbg_en_s          = dbg_en_s;
wire [15:0] UNUSED_dbg_mem_din       = dbg_mem_din;
wire [15:0] UNUSED_dbg_reg_din       = dbg_reg_din;
wire        UNUSED_puc_pnd_set       = puc_pnd_set;
wire  [6:0] UNUSED_dbg_i2c_addr      = dbg_i2c_addr;
wire  [6:0] UNUSED_dbg_i2c_broadcast = dbg_i2c_broadcast;
wire        UNUSED_dbg_i2c_scl       = dbg_i2c_scl;
wire        UNUSED_dbg_i2c_sda_in    = dbg_i2c_sda_in;
wire        UNUSED_dbg_uart_rxd      = dbg_uart_rxd;
`endif
 
 
endmodule // openMSP430
 
`ifdef OMSP_NO_INCLUDE
`else
`include "openMSP430_undefines.v"
`endif
 

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.