OpenCores
URL https://opencores.org/ocsvn/s6soc/s6soc/trunk

Subversion Repositories s6soc

[/] [s6soc/] [trunk/] [doc/] [src/] [spec.tex] - Rev 37

Go to most recent revision | Compare with Previous | Blame | View Log

\documentclass{gqtekspec}
\usepackage{import}
\usepackage{bytefield}
\project{CMod S6 SoC}
\title{Specification}
\author{Dan Gisselquist, Ph.D.}
\email{dgisselq (at) opencores.org}
\revision{Rev.~0.2}
\begin{document}
\pagestyle{gqtekspecplain}
\titlepage
\begin{license}
Copyright (C) \theyear\today, Gisselquist Technology, LLC
 
This project is free software (firmware): you can redistribute it and/or
modify it under the terms of  the GNU General Public License as published
by the Free Software Foundation, either version 3 of the License, or (at
your option) any later version.
 
This program is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
for more details.
 
You should have received a copy of the GNU General Public License along
with this program.  If not, see \texttt{http://www.gnu.org/licenses/} for a copy.
\end{license}
\begin{revisionhistory}
0.2 & 5/14/2016 & Gisselquist & Updated Draft, still not complete \\\hline
0.1 & 4/22/2016 & Gisselquist & First Draft \\\hline
\end{revisionhistory}
% Revision History
% Table of Contents, named Contents
\tableofcontents
\listoffigures
\listoftables
\begin{preface}
The Zip CPU was built with the express purpose of being an area optimized,
32--bit FPGA soft processor.  
 
The S6~SoC is designed to prove that the ZipCPU has met this goal.
\end{preface}
 
\chapter{Introduction}
\pagenumbering{arabic}
\setcounter{page}{1}
 
This project is ongoing.  Any and all files, to include this one, are subject
to change without notice.
 
This project comes from my desire to demonstrate the Zip CPU's utility in a
challenging environment.  The CMod~S6 board fits this role nicely.
\begin{enumerate}
\item The Spartan--6 LX4 FPGA is very limited in its resources: 
	It only has 2,400 look--up tables (LUTs), and can only support 
	a 4,096~Word RAM memory (16 kB).
\item With only 4kW RAM, the majority of any program will need to be placed into
	and run from flash.  (The chip will actually support more, just not
	8k RAM.)
\item While the chip has enough area for the CPU, it doesn't have enough area
	to include the CPU and \ldots write access to the flash, debug access,
	wishbone command access from the UART, pipelined CPU operations, and
	more.  Other solutions will need to be found.
\end{enumerate}
 
Of course, if someone just wants the functionality of a small, cheap, CPU,
this project does not fit that role very well.  While the S6 is not very
expensive, it is still an order of magnitude greater than it's CPU competitors
in price.  This includes such CPU's as the Raspberry Pi Zero, or even the
TeensyLC.
 
If, on the other hand, what you want is a small, cheap, CPU that can be embedded
within an FPGA without using too much of the FPGA's resources, this project
will demonstrate that utility and possibility.  Alternatively, if you wish to
study how to get a CPU to work in a small, constrained environment, this project
may be what you are looking for.
 
\chapter{Architecture}
Fig.~\ref{fig:architecture}
\begin{figure}\begin{center}
\includegraphics[width=5in]{../gfx/s6bones.eps}
\caption{CMod S6 SoC Architecture: ZipCPU and
	Peripherals}\label{fig:architecture}
\end{center}\end{figure}
shows the basic internal architecture of the S6~SoC.  In summary, it consists of a CPU
coupled with a variety of peripherals for the purpose of controlling the
external peripherals of the S6: flash, LEDs, buttons, and GPIO.  External
devices may also be added on, such as an audio device, an external serial
port, an external keypad, and an external display.  All of these devices
are then available for the CPU to interact with.
 
If you are familiar with the Zip CPU, you'll notice this architecture provides
no access to the Zip CPU debug port.  There simply wasn't enough room on the
device.  Debugging the ZipCPU will instead need to take place via other means,
such as dumping all registers and/or memory to the serial port on any reboot.
 
Further, the ZipCPU has no ability to write to flash memory.  For this reason,
there exists an alternate CMod S6~SoC architecture, as shown in
Fig.~\ref{fig:altarchitecture}.
\begin{figure}\begin{center}
\includegraphics[width=5in]{../gfx/altbones.eps}
\caption{Alternate CMod S6 SoC Architecture: Peripherals, with no
	CPU}\label{fig:altarchitecture}
\end{center}\end{figure}
Using this alternate architecture, it should be possible to test the peripherals
and program the flash memory.  Both architectures may be loaded into the flash,
together with the programming code for the Zip CPU.
 
The basic approach to loading the board is actually quite simple.  Using the
Digilent ADEPT JTAG configuration program, {\tt djtgcfg}, the alternate 
configuration may be written directly to the device.  Once this alternate
configuration has been loaded, the flash may be examined and programmed.
This includes programming a primary and alternate configuration into the
configuration section of the flash.  Once complete, the system may then be
reloaded with the primary configuration file which will contain an image of
the CPU.  The CPU will then begin following the instructions found in flash
memory.
 
 
\chapter{Software}
\section{Directory Structure}
\begin{itemize}
\item[{\tt trunk/bench}] Contains software for emulating the S6 without the S6
	present.
  \begin{itemize}
	\item[{\tt trunk/bench/cpp}]  All of the bench testing software is
		written in C++, so it is found in this directory.  Primary
		among these programs is the {\tt zip\_sim} program which will
		simulate the ZipCPU within the S6--Soc.  Specifically, it
		simulates everything at or below the {\tt busmaster.v} level.
 
		Some, although not all, of the peripherals have been simulated
		and made a part of this simulation.  These include the
		Quad--SPI flash, the UART, and the LED's.
 
  \end{itemize}
\item[{\tt trunk/doc}] All of the documentation for the S6SoC project may be
	found in this documentation directory.  Specifically, I would commend
	your attention to anything with a {\tt .pdf} extension, as these
	are the completed documents.  Among these you should find a copy of the
	GPL copyright under which this software is released, as well as a 
	pre--built copy of this document.
  \begin{itemize}
	\item[{\tt trunk/doc/gfx}] Here is where the graphics are located in
		support of this specification document.
	\item[{\tt trunk/doc/src}] And here is where the \LaTeX files are
		kept that were used in building both this document as well as
		the GPL copyright.
  \end{itemize}
\item[{\tt trunk/rtl}] Verilog files
  \begin{itemize}
	\item[{\tt trunk/rtl/cpu}]	Verilog files containing the ZipCPU
		core and peripherals.  The toplevel file here is the
		{\tt zipbones.v} file, although some of the peripherals, such
		as the {\tt ziptimer.v} are referenced independently.
  \end{itemize}
\item[{\tt trunk/sw}] The main software directory, primarily a repository
	for software subdirectories beneath it.
  \begin{itemize}
	\item[{\tt trunk/sw/dev}]  This directory holds a variety of 
		simple programs for the ZipCPU, such as {\tt helloworld},
		{\tt doorbell} and {\tt doorbell2}, as well as software drivers
		for various peripherals, such as the real--time clock simulator,
		and the keypad and display device drivers.
	\item[{\tt trunk/sw/host}]  This directory holds support software which
		can be built on and run on the host machine.  Building this
		software will involve adjusting the Makefile so that it knows
		where your local ADEPT installation directory is.\footnote{Many
		of the programs also depend upon the serial number of my CMod
		S6 device.  This will need to be adjusted in any new install.}
		Once built, you will find a variety of very useful programs
		within here. 
	\item[{\tt trunk/sw/zipos}]  This directory contains the source code for
			a rudimentary, very basic, operating system that I
			call the ZipOS. 
  \end{itemize}
\end{itemize}
 
\section{ZipCPU Tool Chain}
To build programs for the ZipCPU, you will need the ZipCPU toolchain.  You
can find this as part of the ZipCPU project, available at OpenCores.  Building
the ZipCPU project should result in a set of binaries in the
\hbox{\tt trunk/sw/install/cross-tools/bin} directory.  Make this directory
a part of your path, and you should be able to build the CMod S6 ZipCPU
software.  Specifically, you will need to use {\tt zip-gcc}, {\tt zip-as}
{\tt zip-ld}, and {\tt zip-cpp}.  Other tools, such as {\tt zip-objdump} and
{\tt zip-readelf}, may also prove to be very useful when trying to figure out
what is going on within the SoC.
 
\section{Bench Test Software}
 
Bench testing software currently consists of the {\tt zip\_sim} program found
within {\tt trunk/bench/cpp}.  This program requires Verilator to run, and
simulates in a cycle accurate fashion, the entire S6SoC from {\tt busmaster.v}
on down.  Further, the external Quad--SPI flash memory, UART, and LED's are
also simulated, although the 2--line display, audio, and keypad are not.
 
\section{Host Software}
These include:
\begin{itemize}
\item {\tt dumpuart}: My current approach to debugging involves
	dumping the state of the registers and memory to the
	UART upon reboot.  The dumpuart command found here is
	designed to make certain that the UART is first set
	up correctly at 9600~Baud, and that second everything
	read from the UART is directly sent to both a file and
	to the screen.  In this fashion, it is similar to the
	UNIX {\tt tee} program, save for its serial port
	attachment.
\item {\tt readflash}: As I am loathe to remove anything from
	a device that came factory installed, the
	{\tt readflash} program reads the original installed
	configuration from the flash and dumps it to a file.
\item {\tt wbregs}
\item {\tt zipload}: This is the primary program you will need
	to get your software loaded on the CMod.  It takes three
	arguments.  The first is the name of the primary
	Xilinx configuration file, the second is the name
	of the alternate Xilinx configuration file, and the 
	third is the name of the ZipCPU program you wish to 
	write to Flash memory.
 
	Each of these arguments is optional.  For example, if
	only one configuration file is given, the loader will
	load the primary configuration.  If only one ZipCPU
	program is given, the program will be loaded into 
	the program memory area and the configuration file areas
	will be left untouched.
\end{itemize}
\section{ZipCPU Programs}
\begin{itemize}
\item {\tt helloworld}: The first program any programmer should build,
	``Hello, world!''  This program sends the string, ``Hello, world!''
	over the UART connection once per second.  It is a very valuable
	program because, if you can get this program running, you know you have
	a lot of things working and working correctly.  For example, running
	this program means you can run the {\tt zip-gcc} compiler, load
	the auxiliar configuration, load the program info flash memory, load
	the primary configuration, and read from the UART port.  It also means
	that you must have the UART port properly configured and wired to your
	CMod board.
\item {\tt doorbell}: This annoying program verifies the functionality of the
	audio device by playing a doorbell sound to the audio port.  It will
	then wait ten seconds, and play the doorbell sound again (and again,
	and again).  (It gets old after a while ...)
\item {\tt doorbell2}: This adds to the functionality of the {\tt doorbell}
	program a wait for keypress, and a display of the current time on the
	2--line display.  While almost our fully functional program, this
	does not include any menus to configure the device or set time, since
	it doesn't include any keypad functionality.
\item {\tt kptest}: A test of whether or not they keypad driver works.  When
	run, anytime a key is pressed, the key's value (in hex) will be
	sent to the UART.  Further, pressing an `F' on the keypad will also
	send a newline over the UART, in case you wish to keep your lines from
	getting too long.
\end{itemize}
\section{ZipOS}
This operating system is pre--emptive and multitasking, although with many
limitations.  Those familiar with the internals of the Linux kernel may laugh
that I call this an Operating System at all: it has no memory management unit,
no paging, no virtual memory, no file I/O access, no network stack, no ability
to dynamically add or remove tasks, indeed it hardly has any of the things
most often associated with an Operating System.  It does, however, handle
interrupts, support multiple pre--emptive tasks in a multitasking, timesharing
fashion, and it supports some very basic and rudimentary system calls.  In a
similar fashion, it does contain just about all of the functionality necessary
for a multi--tasking microcontroller built around a do--forever loop.  For its
size, I consider it an impressive achievement.  You are welcome to disagree
with me, however.
 
This version of the ZipOS starts in the resetdump.s code, so that upon
any startup the ZipOS will dump register contents, the BusError register, and
any scope contents to the UART.  This can take some time, so you may wish to
configure what you really wish to send--if anything.  If desired, this will
also dump the entire memory as well.  All of this is quite useful in case the
ZipCPU encounters a bus error or other sort of error that causes it to hang,
stall, or reboot, as these registers are very carefully not touched prior to
being sent to the UART output port.
 
{\tt resetdump.s} also calls a rudimentary bootloader, to load the parts of
the ZipOS that need to run faster into Block RAM.  The choice of what parts
to load into Block RAM is made on a file by file basis, and found within
the linker script, {\tt cmodram.ld}.
 
Upon completion, {\tt resetdump.s} calls the entry routine for the O/S,
{\tt kernel\_entry()} found in {\tt kernel.c}.  This is the main task loop for
the entire O/S, and worth studying if you are interested in understanding how
the O/S works.
 
The user tasks are found (mostly) within {\tt doorbell.c}, also found in the
ZipOS directory.  This file contains two kernel entry points, {\tt kntasks()},
which returns the number of tasks the kernel needs to know about, and
{\tt kinit()}, which builds each of the tasks and connects their file 
descriptors to the various devices they will be referencing.
\subsection{Traps}
The ZipOS supports a variety of traps, listed here:
\begin{itemize}
\item WAIT: Halts the execution of a process until an event takes place, or
	a timeout has been reached.  The events that can take place are a
	bitmask of the various interrupts the CPU supports, together with a 
	bitmask of the values found in {\tt swint.h}.
 
	The timeout value can either be zero, to return immediately with the
	list of events that have taken place, negative, to wait indefinitely,
	or a positive number of milliseconds in order to wait at least that
	time for the event of interest to take place.
 
	This also allows a process to sleep for any number of milliseconds.
 
	When wait returns, any events returned by the wait have been cleared.
 
	The other thing to be aware of is that events may accumulate before the
	wait system call.  They will only be returned and cleared, though, if
	the wait call indicates an interest in those events.
\item CLEAR: This system call works closely with the wait system call. 
	Indeed, it is very similar to a wait system call with a zero timeout.
	It clears any of the requested events which may be pending.  If given
	a timeout (in milliseconds), it will start a timer and generate a 
	{\tt SWINT\_TIMEOUT} event to be sent to this process when the timer
	completes.
\item POST: Certain devices, such as the real--time clock and the doorbell
	reader, need the ability of being able to post events to any listener
	within the O/S.  The POST system call allows them to POST events in
	this manner.
\item YIELD: This is simply a way of being nice to other processes.  This system
	call takes no arguments and simply asks the scheduler to schedule the
	next process.  It does not take this process off of the ready to run
	list, so the next process may be this one.  However, since the scheduler
	is a round--robin scheduler, it will only return to this process if
	nothing else is available to run.
\item READ: This is roughly the same system call as the POSIX read() system
	call.  It reads some number of memory addresses (words, not octets),
	to the given file descriptor.  If the memory requested is unavailable,
	the read will wait until it is available, possibly indefinitely.
\item WRITE: This is roughly the same system call as the POSIX write() system
	call.  It writes some number of memory addresses (words, not octets),
	to the given file descriptor.  If nothing is reading from the device,
	the write stall the task forever, otherwise it will only stall the task
	until the data is either written to the receiving task, or copied into
	a memory buffer.
\item TIME: Returns the number of seconds since startup.  Eventually, this will
	return the number of seconds since January 1, 1970, and be identical
	to the UNIX system time() command, but that may not happen on this
	project.
% \item SEMGET
% \item SEMPUT
\item MALLOC: Allocates memory from the system/kernel heap.  This is a very
	low overhead memory allocator that, while it does allocate memory,
	cannot free it later.  It is nearly 100\% efficient since only
	one memory address, the top of the heap, is used to determine what
	memory has been allocated.
\item FREE: Not currently implemented.
\end{itemize}
\subsection{Scheduler}
The ZipCPU currently supports only a round--robin scheduler.  Tasks are executed
in the order they were created, as long as they are available to be executed.
If no tasks are available to be run, the Scheduler will run the idle task which
puts the CPU to sleep while waiting for an interrupt.
 
\chapter{Operation}
 
\chapter{Registers}
There are several address regions on the S6~SoC, as shown in
Tbl.~\ref{tbl:memregions}.
\begin{table}[htbp]
\begin{center}\begin{tabular}{|p{0.75in}|p{0.75in}|p{0.5in}|p{3.0in}|}\hline
\rowcolor[gray]{0.85} Start & End & & Purpose \\\hline\hline
\scalebox{0.9}{\tt 0x000100} & \scalebox{0.9}{\tt 0x000107} & R/W & Peripheral I/O Control \\\hline
\scalebox{0.9}{\tt 0x000200} & \scalebox{0.9}{\tt 0x000201} & R/(W) & Debugging scope\\\hline
\scalebox{0.9}{\tt 0x000400} & \scalebox{0.9}{\tt 0x00043f} & R/W & Internal Configuration Access Port\\\hline
\scalebox{0.9}{\tt 0x000800} & \scalebox{0.9}{\tt 0x000803} & R/W & RTC Clock (if present)\\\hline
\scalebox{0.9}{\tt 0x002000} & \scalebox{0.9}{\tt 0x002fff} & R/W & 16kB On-Chip Block RAM \\\hline
\scalebox{0.9}{\tt 0x400000} & \scalebox{0.9}{\tt 0x7fffff} & R & 16~MB SPI Flash memory\\\hline
\end{tabular}
\caption{Address Regions}\label{tbl:memregions}
\end{center}\end{table}
In general, the address regions that are made up of RAM or flash act like
memory.  The RAM can be read and written, and the flash acts like read only
memory.
 
This isn't quite so true with the other address regions.  Accessing the I/O
region, while it may be read/write, may have side-effects.  For example, reading
from the debugging scope device's data port will read a word from the scope's
buffer and advance the buffer pointer.  
 
\section{Peripheral I/O Control}
Tbl.~\ref{tbl:ioregs}
\begin{table}[htbp]
\begin{center}\begin{reglist}
PIC    &\scalebox{0.8}{\tt 0x0100} & 32 & R/W & Interrupt Controller \\\hline
BUSERR &\scalebox{0.8}{\tt 0x0101} & 32 & R & Last Bus Error Address\\\hline
TIMA   &\scalebox{0.8}{\tt 0x0102} & 32 & R/W & ZipTimer A\\\hline
TIMB   &\scalebox{0.8}{\tt 0x0103} & 32 & R/W & ZipTimer B\\\hline
PWM    &\scalebox{0.8}{\tt 0x0104} & 32 & R/W & PWM Audio Controller\\\hline
SPIO   &\scalebox{0.8}{\tt 0x0105} & 32 & R/W & Special Purpose I/O, Keypad, LED Controller \\\hline
GPIO   &\scalebox{0.8}{\tt 0x0106} & 32 & R/W & GPIO Controller \\\hline
UART   &\scalebox{0.8}{\tt 0x0107} & 32 & R/W & UART data\\\hline
\end{reglist}
\caption{I/O Peripheral Registers}\label{tbl:ioregs}
\end{center}\end{table}
shows the addresses of various I/O peripherals included as part of the SoC.
 
\subsection{Interrupt Controller}
The interrupt controller is identical to the one found with the ZipSystem.
The layout of the PIC bits is shown in Fig.~\ref{fig:picreg}.
\begin{figure}\begin{center}
\begin{bytefield}[endianness=big]{32}
\bitheader{0-31} \\
	\bitbox{1}{E}
	\bitbox{15}{Enabled}
	\bitbox{1}{A}
	\bitbox{15}{ACTIVE}
	\\
\end{bytefield}
\caption{Programmable Interrupt Control (PIC) Register}\label{fig:picreg}
\end{center}\end{figure}
This controller supports up to fifteen interrupts, however only twelve are
defined within the SoC.  If any interrupt line is active, the PIC controller
will have that bit set among it's active set.  Once set, the bit and hence the
interrupt can only be cleared by writing to the controller.  Interrupts can 
also be enabled as well.  The enabled bit mask controls which interrupt lines
are permitted to interrupt the CPU. Hence, just because an interrupt is active
doesn't mean it will interrupt the CPU--the enabled line must be set as well.
Finally, then {\tt A} or {\tt ANY} bit will be high if any interrupts are both
enabled and active, whereas the {\tt E} or global interrupt enable bit can be
set to allow the PIC to interrupt the CPU or cleared to disable all interrupts.
 
To keep operations on this register atomic, most of the bits of this register
have special meanings upon write.  The one exception to this is the global
interrupt enable bit.  On any write, interrupts will be globally enabled or
disabled based upon the value of this bit.  Further, the {\tt ANY} bit is a 
read only bit, so writes to it have no effect.
 
Enabling specific interrupts, via writes to the enable lines, are different.
To enable a specific interrupt, enable all interrupts and
set the wire high associated with the specific interrupt you wish to enable.
Hence writing a {\tt 0x80010000} will enable interrupt line zero, while also
enabling all previously enabled interrupts.
To disable a specific interrupt, disable all interrupts and write a one to the
enable line of the interrupt you wish to disable.  In this fashion, writing a
{\tt 0x00010000} will disable all interrupts and leave interrupt line zero
disabled when the interrupts are re--enabled later, whereas {\tt 0x07fff0000}
will disable all specific interrupts.
 
Interrupts are acknowledged in a fashion similar to enabling interrupts.  By
writing a `1' to the active bit mask, the interrupt will be acknowledged and
reset, whereas writing a `0' leaves the interrupt untouched.  In this fashion,
as individual interrupts are handled, a `1' may be written to this bottom mask
to clear the interrupt.  Be aware, however, that any interrupt acknowledgement
may also globally enable or disable interrupts.
 
\subsection{Last Bus Error Address}
The Bus Error peripheral simply records the address of the last bus error.
This can be useful when debugging.  While the peripheral may only be read,
setting it is really as easy as creating a bus error and trapping the result.
Another use for this is upon any reboot, it is possible to read the address
of the last bus error and perhaps learn something of what caused the CPU to
restart.
 
\subsection{ZipTimer}
The S6 Soc contains two ZipTimers, available for the CPU to use.  These are
countdown timers.  Writing any non--zero value to them will cause them to 
immediately start counting down from that value towards zero, and to interrupt
the CPU when they reach zero.  Writing a new value while the timer is running
will cause that new value to automatically load into the CPU and start counting
from there.  Writing a zero to the timer disables the timer, and causes it to
stop.
 
ZipTimer A can be set to auto reload.  When set, the timer will automatically
load it's last set value upon reaching zero and interrupting the CPU.  This
effectively turns it into an interrupt timer if desired.  To set this feature,
write to the timer the number of clock ticks before an interrupt, but also set
the high order bit.  In this fashion, writing a {\tt 0x80013880} will interrupt
the CPU every millisecond, starting one millisecond after the write takes place
(assuming an 80~MHz system clock).
 
ZipTimer B has been wired for a different purpose.  ZipTimer B does not support
auto reload, nor will it interrupt the CPU.  Instead, ZipTimer B has been wired
as a watchdog timer.  When this timer reaches zero, the CPU will be rebooted.
One way to use this timer would be in conjunction with the ZipTimer A, and to
write a number to it upon any entry to the interrupt service routine.  If given
enough time, this would cause the CPU to reboot if for any reason it locked up.
 
\subsection{PWM Audio Controller}
The bit fields of the PWM Audio controller are shown in Fig.~\ref{fig:pwmreg}.
\begin{figure}\begin{center}
\begin{bytefield}[endianness=big]{32}
\bitheader{0-31} \\
	\bitbox{10}{Unused}
	\bitbox{1}{S}
	\bitbox{1}{G}
	\bitbox{3}{}
	\bitbox{1}{E}
	\bitbox{16}{Sample}
	\\
\end{bytefield}
\caption{PWM Audio Controller Bitfields}\label{fig:pwmreg}
\end{center}\end{figure}
This controller has been designed for easy writing.  To send a sample to the
PWM audio controller, simply write the sample to the controller and clear the
PWM audio interrupt.  When the audio interrupts the CPU again, it is ready
for the next sample.
 
The audio sample rate has been fixed at 8~kHz.  While changing this rate is
easy to do within {\tt busmaster.v}, the rate itself takes some work to keep
up with, so I wouldn't recommend going much (any) faster.
 
The audio controller supports two additional functionalities, however.  The
first is that the {\tt E} bit will be set upon any read when or if the audio
controller is ready for another sample.  Equivalently, the audio interrupt
will be asserted.
 
The second functionality has to do with the two auxiliary control bits present
in the PModAMP2 audio device.  These are the gain and shutdown bits.  To set
these bits, write a sample to the controller while also setting the {\tt E}
bit.  When the {\tt E} bit is set upon any write, the shutdown and gain bits
will also be set.  (Be aware, the shutdown bit is negative logic.)  Hence, one
may start this interface by writing a {\tt 0x0310000} to the device, and later
shut it back off by writing a {\tt 0x010000}.
 
\subsection{Special Purpose I/O}
 
Register {\tt SPIO}, as shown in Fig.~\ref{fig:spioreg},
\begin{figure}\begin{center}
\begin{bytefield}[endianness=big]{32}
\bitheader{0-31} \\
\begin{leftwordgroup}{Read}\bitbox[lrt]{16}{Zeros}
	\bitbox[lrt]{4}{Kpad}
	\bitbox[lrt]{4}{Kpad}
	\bitbox[lrt]{2}{00}
	\bitbox[lrt]{2}{Btn}
	\bitbox[lrt]{4}{LED} \\
\bitbox[lrb]{16}{}
	\bitbox[lrb]{4}{Col Out}
	\bitbox[lrb]{4}{Row In}
	\bitbox[lrb]{2}{}
	\bitbox[lrb]{2}{}
	\bitbox[lrb]{4}{}\end{leftwordgroup} \\
\begin{leftwordgroup}{Write}\bitbox[lrt]{16}{Ignored}
	\bitbox[lrt]{4}{Col}
	\bitbox[lrt]{4}{Col}
	\bitbox[lrt]{4}{LED}
	\bitbox[lrt]{4}{LED} \\
\bitbox[lrb]{16}{}
	\bitbox[lrb]{4}{Out}
	\bitbox[lrb]{4}{Enable}
	\bitbox[lrb]{4}{Enable}
	\bitbox[lrb]{4}{}\end{leftwordgroup} \\
\end{bytefield}
\caption{SPIO Control Register}\label{fig:spioreg}
\end{center}\end{figure}
is a Special Purpose Input/Output (SPIO) register. It is
designed to control the on-board LED's, buttons, and keypad.  Upon any read,
the register reads the current state of the keypad column output, the keypad
row input, the buttons and the LED's.  Writing is more difficult, in order to
make certain that parts of these registers can be modified atomically.  
Specifically, to change an LED, write the new value as well as a `1' to the
corresponding LED change enable bit.  The same goes for the keypad column
output, a `1' needs to be written to the change enable bit in order for a 
new value to be accepted.
 
As examples, writing a {\tt 0x0ff} to the {\tt SPIO} register will turn all
LED's on, {\tt 0x0f0} will turn all LED's off, and {\tt 0x011} and {\tt 0x010}
will turn LED0 on and then off again respectively.
 
The controller will generate a keypad interrupt whenever any row input is
zero, and a button interrupt whenever any button value is a one.  This also
means that, once generated, the interrupt must be disabled until the key or
button is released.
 
\subsection{General Purpose I/O}
The General Purpose Input and Output (GPIO) control register, shown in 
Fig.~\ref{fig:gpioreg},
\begin{figure}\begin{center}
\begin{bytefield}[endianness=big]{32}
\bitheader{0-31} \\
\bitbox[lrtb]{16}{Current Input Vals (x16)}\bitbox[lrt]{16}{Current Output} \\
\bitbox[lrtb]{16}{Output Change Enable}\bitbox[lrb]{16}{Values (16-outs)} 
\end{bytefield}
\caption{GPIO Control Register}\label{fig:gpioreg}
\end{center}\end{figure}
is quite simple to use: when read, the top 16--bits indicate
the value of the 16--input GPIO pins, whereas the bottom 16--bits indicate
the value being placed on the 16--output GPIO pins.  To change a GPIO pin,
write the new pin's value to this register, together with setting the
corresponding pin in the upper 16--bits.  For example, to set output pin 0,
write a {\tt 0x010001} to the GPIO device.  To clear output pin 0, write a 
{\tt 0x010000}.  This makes it possible to adjust some output pins independent
of the others.
 
The GPIO controller, like the keypad or SPIO controller, will also generate
an interrupt.  The GPIO interrupt is generated whenever a GPIO input line
changes.  The interrupt is not selective: if any line changes, a GPIO interrupt
will be generated.  There are no do not care lines.
 
Of the 16 GPIO inputs and the 16 GPIO outputs, two lines have been taken for
I2C support.  GPIO line zero, for both input and output, is an I2C data line,
{\tt io\_sda}, and GPIO line one is an I2C clock line, {\tt io\_scl}.  If the
output of either of these
lines is set to zero, the GPIO controller will drive the line.  Otherwise,
the line is pulled up with a weak resistor so that other devices may
pull it low.  If either line is low, when the output control bit is high,
it is an indicator that another device is sending data across these wires.
 
\subsection{UART Data Register}
Moving on to the UART \ldots
although the UART module within the S6~SoC is highly configurable, as built
the UART can only handle 9600~Baud, 8--data bits, no parity, and one stop bit.
Changing this involves changing the constant {\tt uart\_setup} within 
{\tt busmaster.v}.  Further,  the UART has only a single byte data buffer, so
reading from the port has a real--time requirement associated with it--the
data buffer must be emptied before the next value is read. 
Attempts to read from this port will either return an 8--bit data value from
the port, or if no values are available it will return an {\tt 0x0100}
indicating that fact.  In general, reading from the UART port involves first
waiting for the interrupt to be ready, second reading from the port itself,
and then third immediately  clearing the interrupt.  (The interrupt cannot
be cleared while data is waiting.)  Writing to the UART port is done in a 
similar fashion.  First, wait until the UART transmit interrupt is asserted,
second write to the UART port, and then third clear the interrupt.  As with
the read interrupt, clearing the interrupt prior to writing to the port will
have no effect.
 
\section{Debugging Scope}
The debugging scope consists of two registers, a control register and a data
register.  It needs to be internally wired to 32--wires, internal to the S6
SoC, that will be of interest later.  For further details on how to configure
and use this scope, please see the {\tt WBSCOPE} project on OpenCores.
 
\section{Internal Configuration Access Port}
The Internal Configuration Access Port (ICAP) provides access to the internal
configuration details of the FPGA.  This access was designed so as to provide
the CPU with the capability to command a different FPGA load.  In particular,
the code in Fig.~\ref{fig:reload} should reconfigure the FPGA from any given
Quad SPI {\tt address}.\footnote{According to Xilinx's technical support, this
will only work if the JTAG port is not busy.}
\begin{figure}\begin{center}\begin{tabbing}
{\tt warmboot(uint32 address) \{} \\
\hbox to 0.25in{}\={\tt uint32\_t *icape6 = (volatile uint32\_t *)0x{\em <ICAPE port address>};}\\
 \>{\tt icape6[13] = (address<<2)\&0x0ffff;}\\
 \>{\tt icape6[14] = ((address>>14)\&0x0ff)|((0x03)<<8);}\\
 \>{\tt icape6[4] = 14;}\\
 \>{\em // The CMod~S6 is now reconfiguring itself from the new address.}\\
 \>{\em // If all goes well, this routine will never return.}\\
{\tt \}}
\end{tabbing}
\caption{Spartan--6 ICAPE Usage}\label{fig:reload}
\end{center}\end{figure}
 
One subtle problem with this port is that it will not work if the CMod is
plugged in to the USB JTAG port.  It will only work if the CMod has been
provided with an independent power supply, leaving the USB JTAG unplugged.
 
For further details, please see either the {\tt WBICAPETWO} project on OpenCores
as well as Xilinx's ``Spartan-6 FPGA Configuration User Guide''.
 
\section{Real--Time Clock}
The Real Time Clock will be included if there is enough area to support it.
The four registers correspond to a clock, a timer, a stopwatch, and an alarm.
If space is tight, the timer and stopwatch, or indeed the entire clock, may be
removed from the design.  For further details regarding how to set and use this
clock, please see the {\tt RTCCLOCK} project on OpenCores.
 
There is currently not enough area on the chip to support the Real--Time Clock
together with all of the other peripherals listed here.  You can adjust whether
the clock is included or not by adjusting the {\tt `define} lines at the top
of {\tt busmaster.v}.  For example, it may be possible to get the RTC back by
disabling the ICAPE2 interface.
 
\section{On-Chip Block RAM}
 
The block RAM is the fastest memory available to the processor.  It is also 
the {\em only} writeable memory available to the processor.  Hence all 
non-constant program data {\em must} be placed into block RAM.  The ZipCPU
can also run instructions from the block RAM if extra speed is desired.  When
runnning from block RAM, the ZipCPU will nominally take 8~clocks per
instruction, for an effective rate of 8~MIPS.  Loads or stores to block RAM
will take one instruction longer.  
 
\section{Flash Memory}
The flash memory has been arbitrarily sectioned into three sections, one for
a primary configuration, a second section for an alternate configuration file,
and the third section for any program and data.  These regions are shown in
Tbl.~\ref{tbl:flash-addresses}.
\begin{table}[htbp]
\begin{center}\begin{tabular}{|p{0.75in}|p{0.75in}|p{0.5in}|p{3.0in}|}\hline
\rowcolor[gray]{0.85} Start & End & & Purpose \\\hline\hline
\scalebox{0.9}{\tt 0x400000} & \scalebox{0.9}{\tt 0x43ffff} & R & Primary configuration space\\\hline
\scalebox{0.9}{\tt 0x440000} & \scalebox{0.9}{\tt 0x47ffff} & R & Alternate configuration space\\\hline
\scalebox{0.9}{\tt 0x480000} & \scalebox{0.9}{\tt 0x7fffff} & R & ZipCPU program memory\\\hline
\end{tabular}
\caption{Flash Address Regions}\label{tbl:flash-addresses}
\end{center}\end{table}
The host program {\tt zipload} can be used to load a ZipCPU program and
configuration files into this address space.  To use it, first load the
alternate configuration into the FPGA.  Then pass it, as arguments, the
primary, and alternate if desired, configuration files followed by the ZipCPU
program file.  Then, when the primary configuration is loaded again, perhaps
upon power up, the ZipCPU will automatically start running from it's 
{\tt RESET\_ADDRESS}, {\tt 0x480000}.
 
When running from Flash memory, the ZipCPU will nominally take 52~clocks per
instruction, for an effective speed of about 1.5~MIPS.
 
\chapter{Clocks}
 
The S6~SoC is designed to run off of one master clock.  This clock is derived
from the 8~MHz input clock on the board, by multiplying it up to 80~MHz.
 
\chapter{IO Ports}
 
See Table.~\ref{tbl:ioports}.
\begin{table}[htbp]
\begin{center}
\begin{portlist}
i\_clk\_8mhz & 1 & Input & Clock\\\hline
o\_qspi\_cs\_n & 1 & Output & Quad SPI Flash chip select\\\hline
o\_qspi\_sck & 1 & Output & Quad SPI Flash clock\\\hline
io\_qspi\_dat & 4 & Input/Output & Four-wire SPI flash data bus\\\hline
i\_btn & 2 & Input  & Inputs from the two on-board push-buttons\\\hline
o\_led & 4 & Output & Outputs controlling the four on-board LED's\\\hline
o\_pwm & 1 & Output & Audio output, via pulse width modulator\\\hline
\multicolumn{2}{|l|}{o\_pwm\_shutdown\_n, 1}& Output & Audio output shutdown control\\\hline
o\_pwm\_gain & 1 & Output & Audio output 20~dB gain enable\\\hline
i\_uart & 1 & Input &  UART receive input\\\hline
o\_uart & 1 & Output & UART transmit output\\\hline
i\_uart\_cts & 1 & Input &  \\\hline
o\_uart\_rts & 1 & Output & \\\hline
i\_kp\_row & 4 & Output & Four wires to activate the four rows of the keypad\\\hline
o\_kp\_col & 4 & Output & Return four wires, from the keypads columns \\\hline
i\_gpio & 14 & Output & General purpose logic input lines\\\hline
o\_gpio & 14 & Output & General purpose logic output lines\\\hline
io\_scl & 1 & Input/Output & I2C clock port\\\hline
io\_sda & 1 & Input/Output & I2C data port\\\hline
\end{portlist}
\caption{List of IO ports}\label{tbl:ioports}
\end{center}\end{table}
 
\begin{table}
\begin{center}
\includegraphics[height=7in]{../gfx/pinout.eps}
\caption{Physical Locations of Device I/O Ports}\label{tbl:physicalio}
\end{center}\end{table}
% Appendices
% Index
\end{document}
 
 
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.