OpenCores
URL https://opencores.org/ocsvn/udp_ip_stack/udp_ip_stack/trunk

Subversion Repositories udp_ip_stack

[/] [udp_ip_stack/] [trunk/] [rtl/] [vhdl/] [arp_STORE_br.vhd] - Rev 10

Go to most recent revision | Compare with Previous | Blame | View Log

----------------------------------------------------------------------------------
-- Company: 
-- Engineer: 		Peter Fall
-- 
-- Create Date:    12:00:04 05/31/2011 
-- Design Name: 
-- Module Name:    arp_STORE_br - Behavioral 
-- Project Name: 
-- Target Devices: 
-- Tool versions: 
-- Description:
--		ARP storage table using block ram with lookup based on IP address
--		implements upto 255 entries with sequential search
--		uses round robin overwrite when full (LRU would be better, but ...)
--
--		store may take a number of cycles and the request is latched
--		lookup may take a number of cycles. Assumes that request signals remain valid during lookup
--
-- Dependencies: 
--
-- Revision: 
-- Revision 0.01 - File Created
-- Additional Comments: 
--
----------------------------------------------------------------------------------
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.NUMERIC_STD.ALL;
use ieee.std_logic_unsigned.all;
use work.arp_types.all;
 
entity arp_STORE_br is
	generic (
			MAX_ARP_ENTRIES : integer := 255							-- max entries in the store
			);
	Port (
			-- read signals
			read_req				: in arp_store_rdrequest_t;		-- requesting a lookup or store
			read_result			: out arp_store_result_t;			-- the result
			-- write signals
			write_req			: in arp_store_wrrequest_t;		-- requesting a lookup or store
			-- control and status signals
			clear_store			: in std_logic;						-- erase all entries
			entry_count			: out unsigned(7 downto 0);		-- how many entries currently in store
			-- system signals
			clk					: in std_logic;
			reset 				: in  STD_LOGIC
			);
end arp_STORE_br;
 
architecture Behavioral of arp_STORE_br is
 
	type st_state_t is (IDLE,PAUSE,SEARCH,FOUND,NOT_FOUND);
 
	type ip_ram_t is array (0 to MAX_ARP_ENTRIES-1) of std_logic_vector(31 downto 0);
	type mac_ram_t is array (0 to MAX_ARP_ENTRIES-1) of std_logic_vector(47 downto 0);
	subtype addr_t is integer range 0 to MAX_ARP_ENTRIES;
 
	type count_mode_t is (RST,INCR,HOLD);
 
	type mode_t is (MREAD,MWRITE);
 
	-- state variables
	signal ip_ram					: ip_ram_t;										-- will be implemented as block ram
	signal mac_ram					: mac_ram_t;									-- will be implemented as block ram	
	signal st_state				: st_state_t;
	signal next_write_addr		: addr_t;										-- where to make the next write
	signal num_entries			: addr_t; 										-- number of entries in the store
	signal next_read_addr		: addr_t; 										-- next addr to read from
	signal entry_found			: arp_entry_t;									-- entry found in search
	signal mode						: mode_t;										-- are we writing or reading?
	signal req_entry				: arp_entry_t;									-- entry latched from req
 
	-- busses
	signal next_st_state			: st_state_t;
	signal arp_entry_val			: arp_entry_t;
	signal mode_val				: mode_t;
	signal write_addr				: addr_t; 										-- actual write address to use
 
	-- control signals
	signal set_st_state		: std_logic;
	signal set_next_write_addr	: count_mode_t;
	signal set_num_entries		: count_mode_t;
	signal set_next_read_addr	: count_mode_t;
	signal write_ram				: std_logic;
	signal set_entry_found		: std_logic;
	signal set_mode				: std_logic;
 
	function read_status(status : arp_store_rslt_t; signal mode : mode_t) return arp_store_rslt_t is
		variable ret : arp_store_rslt_t;
	begin
		case status is
			when IDLE =>
				ret := status;
			when others =>
				if mode = MWRITE then
					ret := BUSY;
				else
					ret := status;
				end if;
		end case;
		return ret;
	end read_status;
 
begin
	combinatorial : process (
		-- input signals
		read_req, write_req, clear_store, reset, 
		-- state variables
		ip_ram, mac_ram, st_state, next_write_addr, num_entries, 
		next_read_addr, entry_found, mode, req_entry, 
		-- busses
		next_st_state, arp_entry_val, mode_val, write_addr, 
		-- control signals
		set_st_state, set_next_write_addr, set_num_entries, set_next_read_addr, set_entry_found, 
		write_ram, set_mode
		)
	begin
		-- set output followers
		read_result.status <= IDLE;
		read_result.entry <= entry_found;
		entry_count <= to_unsigned(num_entries,8);
 
		-- set bus defaults
		next_st_state <= IDLE;
		mode_val <= MREAD;
		write_addr <= next_write_addr;
 
		-- set signal defaults
		set_st_state <= '0';
		set_next_write_addr <= HOLD;
		set_num_entries <= HOLD;
		set_next_read_addr <= HOLD;
		write_ram <= '0';
		set_entry_found <= '0';
		set_mode <= '0';
 
		-- STORE FSM
		case st_state is
			when IDLE =>
				if write_req.req = '1' then
					-- need to search to see if this IP already there
					set_next_read_addr <= RST;			-- start lookup from beginning
					mode_val <= MWRITE;
					set_mode <= '1';
					next_st_state <= PAUSE;
					set_st_state <= '1';				
				elsif read_req.req = '1' then
					set_next_read_addr <= RST;			-- start lookup from beginning
					mode_val <= MREAD;
					set_mode <= '1';
					next_st_state <= PAUSE;
					set_st_state <= '1';
				end if;
 
			when PAUSE =>
				-- wait until read addr is latched and we get first data out of the ram
				read_result.status <= read_status(BUSY,mode);
				set_next_read_addr <= INCR;
				next_st_state <= SEARCH;
				set_st_state <= '1';
 
			when SEARCH =>
				read_result.status <= read_status(SEARCHING,mode);
				-- check if have a match at this entry
				if req_entry.ip = arp_entry_val.ip and next_read_addr <= num_entries then
					-- found it
					set_entry_found <= '1';
					next_st_state <= FOUND;
					set_st_state <= '1';
				elsif next_read_addr > num_entries or next_read_addr >= MAX_ARP_ENTRIES then
					-- reached end of entry table
					read_result.status <= read_status(NOT_FOUND,mode);
					next_st_state <= NOT_FOUND;
					set_st_state <= '1';
				else
					-- no match at this entry , go to next
					set_next_read_addr <= INCR;
				end if;
 
			when FOUND =>			
				read_result.status <= read_status(FOUND,mode);
				if mode = MWRITE then
					write_addr <= next_read_addr - 1;
					write_ram <= '1';
					next_st_state <= IDLE;
					set_st_state <= '1';
				elsif read_req.req = '0' then			-- wait in this state until request de-asserted
					next_st_state <= IDLE;
					set_st_state <= '1';
				end if;
 
			when NOT_FOUND =>			
				read_result.status <= read_status(NOT_FOUND,mode);
				if mode = MWRITE then
					-- need to write into the next free slot
					write_addr <= next_write_addr;
					write_ram <= '1';
					set_next_write_addr <= INCR;
					if num_entries < MAX_ARP_ENTRIES then
						-- if not full, count another entry (if full, it just wraps)
						set_num_entries <= INCR;
					end if;
					next_st_state <= IDLE;
					set_st_state <= '1';
				elsif read_req.req = '0' then			-- wait in this state until request de-asserted
					next_st_state <= IDLE;
					set_st_state <= '1';
				end if;
 
		end case;		
	end process;
 
	sequential : process (clk)
	begin
		if rising_edge(clk) then
			-- ram processing
			if write_ram = '1' then
				ip_ram(write_addr) <= req_entry.ip;
				mac_ram(write_addr) <= req_entry.mac;
			end if;
			if next_read_addr < MAX_ARP_ENTRIES then
				arp_entry_val.ip <= ip_ram(next_read_addr);
				arp_entry_val.mac <= mac_ram(next_read_addr);
			else
				arp_entry_val.ip <= (others => '0');
				arp_entry_val.mac <= (others => '0');
			end if;
 
			if reset = '1' or clear_store = '1' then
				-- reset state variables
				st_state <= IDLE;
				next_write_addr <= 0;
				num_entries <= 0;
				next_read_addr <= 0;
				entry_found.ip <= (others => '0');
				entry_found.mac <= (others => '0');
				req_entry.ip <= (others => '0');
				req_entry.mac <= (others => '0');
				mode <= MREAD;
 
			else
				-- Next req_state processing
				if set_st_state = '1' then
					st_state <= next_st_state;
				else
					st_state <= st_state;
				end if;
 
				-- mode setting and write request latching
				if set_mode = '1' then
					mode <= mode_val;
					if mode_val = MWRITE then
						req_entry <= write_req.entry;
					else
						req_entry.ip <= read_req.ip;
						req_entry.mac <= (others => '0');
					end if;
				else
					mode <= mode;
					req_entry <= req_entry;
				end if;
 
				-- latch entry found
				if set_entry_found = '1' then
					entry_found <= arp_entry_val;
				else
					entry_found <= entry_found;
				end if;
 
				-- next_write_addr counts and wraps
				case set_next_write_addr is
					when HOLD => next_write_addr <= next_write_addr;
					when RST => next_write_addr <= 0;
					when INCR => if next_write_addr < MAX_ARP_ENTRIES-1 then next_write_addr <= next_write_addr + 1;  else next_write_addr <= 0; end if;
				end case;
 
				-- num_entries counts and holds at max
				case set_num_entries is
					when HOLD => num_entries <= num_entries;
					when RST => num_entries <= 0;
					when INCR => if next_write_addr < MAX_ARP_ENTRIES then num_entries <= num_entries + 1; else num_entries <= num_entries; end if;
				end case;
 
				-- next_read_addr counts and wraps
				case set_next_read_addr is
					when HOLD => next_read_addr <= next_read_addr;
					when RST => next_read_addr <= 0;
					when INCR => if next_read_addr < MAX_ARP_ENTRIES then next_read_addr <= next_read_addr + 1; else next_read_addr <= 0; end if;
				end case;
 
			end if;						
		end if;
	end process;
 
end Behavioral;
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.