Subversion Repositories wbuart32

////////////////////////////////////////////////////////////////////////////////
//
// Filename: 	speechfifo.v
//
// Project:	wbuart32, a full featured UART with simulator
//
// Purpose:	To test/demonstrate/prove the wishbone access to the FIFO'd
//		UART via sending more information than the FIFO can hold,
//	and then verifying that this was the value received.
//
//	To do this, we "borrow" a copy of Abraham Lincolns Gettysburg address,
//	make that the FIFO isn't large enough to hold it, and then try
//	to send this address every couple of minutes.
//
//	With some minor modifications (discussed below), this RTL should be
//	able to be run as a top-level testing file, requiring only that the
//	clock and the transmit UART pins be working.
//
// Creator:	Dan Gisselquist, Ph.D.
//		Gisselquist Technology, LLC
//
////////////////////////////////////////////////////////////////////////////////
//
// Copyright (C) 2015-2016, Gisselquist Technology, LLC
//
// This program is free software (firmware): you can redistribute it and/or
// modify it under the terms of  the GNU General Public License as published
// by the Free Software Foundation, either version 3 of the License, or (at
// your option) any later version.
//
// This program is distributed in the hope that it will be useful, but WITHOUT
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
//
// You should have received a copy of the GNU General Public License along
// with this program.  (It's in the $(ROOT)/doc directory, run make with no
// target there if the PDF file isn't present.)  If not, see
// <http://www.gnu.org/licenses/> for a copy.
//
// License:	GPL, v3, as defined and found on www.gnu.org,
//		http://www.gnu.org/licenses/gpl.html
//
//
////////////////////////////////////////////////////////////////////////////////
//
//
// Uncomment the next line if you want this program to work as a standalone
// (not verilated) RTL "program" to test your UART.  You'll also need to set
// your i_setup condition properly, though (below).  I recommend setting it to 
// the ratio of your onboard clock to your desired baud rate.  For more
// information about how to set this, please see the specification.
//
//`define OPT_STANDALONE
//
module	speechfifo(i_clk,
`ifndef	OPT_STANDALONE
			i_setup,
`endif
			o_uart_tx);
	input		i_clk;
	output	wire	o_uart_tx;
 
	// Here we set i_setup to something appropriate to create a 115200 Baud
	// UART system from a 100MHz clock.  This also sets us to an 8-bit data
	// word, 1-stop bit, and no parity.  This will be overwritten by
	// i_setup, but at least it gives us something to start with/from.
	parameter	INITIAL_UART_SETUP = 30'd868;
 
	// The i_setup wires are input when run under Verilator, but need to
	// be set internally if this is going to run as a standalone top level
	// test configuration.
`ifdef	OPT_STANDALONE
	wire	[29:0]	i_setup;
	assign	i_setup = INITIAL_UART_SETUP;
`else
	input	[29:0]	i_setup;
`endif
 
	reg		restart;
	reg		wb_stb;
	reg	[1:0]	wb_addr;
	reg	[31:0]	wb_data;
 
	wire		uart_stall, uart_ack;
	wire	[31:0]	uart_data;
 
	wire		tx_int, txfifo_int;
 
	// The next four lines create a strobe signal that is true on the first
	// clock, but never after.  This makes for a decent power-on reset
	// signal.
	reg	pwr_reset;
	initial	pwr_reset = 1'b1;
	always @(posedge i_clk)
		pwr_reset <= 1'b0;
 
	// The message we wish to transmit is kept in "message".  It needs to be
	// set initially.  Do so here.
	//
	// Since the message has fewer than 2048 elements in it, we preset every
	// element to a space so that if (for some reason) we broadcast past the
	// end of our message, we'll at least be sending something useful.
	integer	i;
	reg	[7:0]	message [0:2047];
	initial begin
		$readmemh("speech.hex",message);
		for(i=1481; i<2048; i=i+1)
			message[i] = 8'h20;
	end
 
	// Let's keep track of time, and send our message over and over again.
	// To do this, we'll keep track of a restart counter.  When this counter
	// rolls over, we restart our message.
	reg	[30:0]	restart_counter;
	// Since we want to start our message just a couple clocks after power
	// up, we'll set the reset counter just a couple clocks shy of a roll
	// over.
	initial	restart_counter = -31'd16;
	always @(posedge i_clk)
		restart_counter <= restart_counter+1'b1;
 
	// Ok, now that we have a counter that tells us when to start over,
	// let's build a set of signals that we can use to get things started
	// again.  This will be the restart signal.  On this signal, we just
	// restart everything.
	initial	restart = 0;
	always @(posedge i_clk)
		restart <= (restart_counter == 0);
 
	// Our message index.  This is the address of the character we wish to
	// transmit next.  Note, there's a clock delay between setting this 
	// index and when the wb_data is valid.  Hence, we set the index on
	// restart[0] to zero.
	reg	[10:0]	msg_index;
	initial	msg_index = 11'd2040;
	always @(posedge i_clk)
	begin
		if (restart)
			msg_index <= 0;
		else if ((wb_stb)&&(!uart_stall))
			// We only advance the index if a port operation on the
			// wbuart has taken place.  That's what the
			// (wb_stb)&&(!uart_stall) is about.  (wb_stb) is the
			// request for a transaction on the bus, uart_stall
			// tells us to wait 'cause the peripheral isn't ready. 
			// In our case, it's always ready, uart_stall == 0, but
			// we keep/maintain this logic for good form.
			//
			// Note also, we only advance when restart[0] is zero.
			// This keeps us from advancing prior to the setup
			// word.
			msg_index <= msg_index + 1'b1;
	end
 
	// What data will we be sending to the port?
	always @(posedge i_clk)
		if (restart)
			// The first thing we do is set the baud rate, and
			// serial port configuration parameters.  Ideally,
			// we'd only set this once.  But rather than complicate
			// the logic, we set it everytime we start over.
			wb_data <= { 2'b00, i_setup };
		else if ((wb_stb)&&(!uart_stall))
			// Then, if the last thing was received over the bus,
			// we move to the next data item.
			wb_data <= { 24'h00, message[msg_index] };
 
	// We send our first value to the SETUP address (all zeros), all other
	// values we send to the transmitters address.  We should really be
	// double checking that stall remains low, but its not required here.
	always @(posedge i_clk)
		if (restart)
			wb_addr <= 2'b00;
		else // if (!uart_stall)??
			wb_addr <= 2'b11;
 
	// Knowing when to stop sending the speech is important, but depends
	// upon an 11 bit comparison.  Since FPGA logic is best measured by the
	// number of inputs to an always block, we pull those 11-bits out of
	// the always block for wb_stb, and place them here on the clock prior.
	// If end_of_message is true, then we need to stop transmitting, and
	// wait for the next (restart) to get us started again.  We set that
	// flag hee.
	reg	end_of_message;
	initial	end_of_message = 1'b1;
	always @(posedge i_clk)
		if (restart)
			end_of_message <= 1'b0;
		else
			end_of_message <= (msg_index >= 1481);
 
	// The wb_stb signal indicates that we wish to write, using the wishbone
	// to our peripheral.  We have two separate types of writes.  First,
	// we wish to write our setup.  Then we want to drop STB and write
	// our data.  Once we've filled half of the FIFO, we wait for the FIFO
	// to empty before issuing a STB again and then fill up half the FIFO
	// again.
	initial	wb_stb = 1'b0;
	always @(posedge i_clk)
		if (restart)
			// Start sending to the UART on a reset.  The first
			// thing we'll send will be the configuration, but
			// that's done elsewhere.  This just starts up the
			// writes to the peripheral wbuart.
			wb_stb <= 1'b1;
		else if (end_of_message)
			// Stop transmitting when we get to the end of our
			// message.
			wb_stb <= 1'b0;
		else if (tx_int)
			// If we aren't at the end of the message, and tx_int
			// tells us the FIFO is empty, then start writing into
			// the FIFO>
			wb_stb <= 1'b1;
		else if (txfifo_int)
			// If we are writing into the FIFO, and it's less than
			// half full (i.e. txfifo_int is true) then keep going.
			wb_stb <= wb_stb;
		else
			// But once the FIFO gets to half full, stop.
			wb_stb <= 1'b0;
 
	// We aren't using the receive interrupts, so we'll just mark them
	// here as ignored.
	wire	ignored_rx_int, ignored_rxfifo_int;
 
	// Finally--the unit under test--now that we've set up all the wires
	// to run/test it.
	wbuart	#(INITIAL_UART_SETUP)
		wbuarti(i_clk, pwr_reset,
			wb_stb, wb_stb, 1'b1, wb_addr, wb_data,
			uart_stall, uart_ack, uart_data,
			1'b1, o_uart_tx,
			ignored_rx_int, tx_int,
			ignored_rxfifo_int, txfifo_int);
 
endmodule