OpenCores
URL https://opencores.org/ocsvn/zipcpu/zipcpu/trunk

Subversion Repositories zipcpu

[/] [zipcpu/] [trunk/] [rtl/] [core/] [memops.v] - Rev 5

Go to most recent revision | Compare with Previous | Blame | View Log

///////////////////////////////////////////////////////////////////////////
//
// Filename:	memops.v
//
// Project:	Zip CPU -- a small, lightweight, RISC CPU soft core
//
// Purpose:	A memory unit to support a CPU.
//
//	In the interests of code simplicity, this memory operator is 
//	susceptible to unknown results should a new command be sent to it
//	before it completes the last one.  Unpredictable results might then
//	occurr.
//
// Creator:	Dan Gisselquist, Ph.D.
//		Gisselquist Tecnology, LLC
//
///////////////////////////////////////////////////////////////////////////
//
// Copyright (C) 2015, Gisselquist Technology, LLC
//
// This program is free software (firmware): you can redistribute it and/or
// modify it under the terms of  the GNU General Public License as published
// by the Free Software Foundation, either version 3 of the License, or (at
// your option) any later version.
//
// This program is distributed in the hope that it will be useful, but WITHOUT
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
//
// License:	GPL, v3, as defined and found on www.gnu.org,
//		http://www.gnu.org/licenses/gpl.html
//
//
///////////////////////////////////////////////////////////////////////////
//
module	memops(i_clk, i_rst, i_stb,
		i_op, i_addr, i_data, i_oreg,
			o_busy, o_valid, o_wreg, o_result,
		o_wb_cyc, o_wb_stb, o_wb_we, o_wb_addr, o_wb_data,
		i_wb_ack, i_wb_stall, i_wb_data);
	input			i_clk, i_rst;
	input			i_stb;
	// CPU interface
	input			i_op;
	input		[31:0]	i_addr;
	input		[31:0]	i_data;
	input		[4:0]	i_oreg;
	// CPU outputs
	output	wire		o_busy;
	output	reg		o_valid;
	output	reg	[4:0]	o_wreg;
	output	reg	[31:0]	o_result;
	// Wishbone outputs
	output	reg		o_wb_cyc, o_wb_stb, o_wb_we;
	output	reg	[31:0]	o_wb_addr, o_wb_data;
	// Wishbone inputs
	input			i_wb_ack, i_wb_stall;
	input		[31:0]	i_wb_data;
 
	always @(posedge i_clk)
		if (i_rst)
			o_wb_cyc <= 1'b0;
		else if (o_wb_cyc)
			o_wb_cyc <= (~i_wb_ack);
		else if (i_stb) // New memory operation
			// Grab the wishbone
			o_wb_cyc  <= 1'b1;
	always @(posedge i_clk)
		if (o_wb_cyc)
			o_wb_stb <= (o_wb_stb)&&(i_wb_stall);
		else
			o_wb_stb  <= i_stb; // Grab wishbone on new operation
	always @(posedge i_clk)
		if (i_stb)
		begin
			o_wb_we   <= i_op;
			o_wb_data <= i_data;
			o_wb_addr <= i_addr;
		end
 
	initial	o_valid = 1'b0;
	always @(posedge i_clk)
		o_valid <= (o_wb_cyc)&&(i_wb_ack)&&(~o_wb_we);
	assign	o_busy = o_wb_cyc;
 
	always @(posedge i_clk)
		if (i_stb)
			o_wreg    <= i_oreg;
	always @(posedge i_clk)
		if (i_wb_ack)
			o_result <= i_wb_data;
endmodule
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.