Subversion Repositories zipcpu

[/] [zipcpu/] [trunk/] [rtl/] [peripherals/] [zipcounter.v] - Rev 2

Go to most recent revision | Compare with Previous | Blame | View Log

// Filename:	zipcounter.v
// Project:	Zip CPU -- a small, lightweight, RISC CPU soft core
// Purpose:
//		A very, _very_ simple counter.  It's purpose doesn't really
//	include rollover, but it will interrupt on rollover.  It can be set,
//	although my design concept is that it can be reset.  It cannot be
//	halted.  It will always produce interrupts--whether or not they are 
//	handled interrupts is another question--that's up to the interrupt
//	controller.
//	My intention is to use this counter for process accounting: I should
//	be able to use this to count clock ticks of processor time assigned to
//	each task by resetting the counter at the beginning of every task
//	interval, and reading the result at the end of the interval.  As long
//	as the interval is less than 2^32 clocks, there should be no problem.
//	Similarly, this can be used to measure CPU wishbone bus stalls, 
//	prefetch stalls, or other CPU stalls (i.e. stalling as part of a JMP
//	instruction, or a read from the condition codes following a write).
// Creator:	Dan Gisselquist, Ph.D.
//		Gisselquist Tecnology, LLC
// Copyright (C) 2015, Gisselquist Technology, LLC
// This program is free software (firmware): you can redistribute it and/or
// modify it under the terms of  the GNU General Public License as published
// by the Free Software Foundation, either version 3 of the License, or (at
// your option) any later version.
// This program is distributed in the hope that it will be useful, but WITHOUT
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
// License:	GPL, v3, as defined and found on,
module	zipcounter(i_clk, i_ce,
		i_wb_cyc, i_wb_stb, i_wb_we, i_wb_data,
			o_wb_ack, o_wb_stall, o_wb_data,
	parameter	BW = 32;
	input				i_clk, i_ce;
	// Wishbone inputs
	input				i_wb_cyc, i_wb_stb, i_wb_we;
	input		[(BW-1):0]	i_wb_data;
	// Wishbone outputs
	output	reg			o_wb_ack;
	output	wire			o_wb_stall;
	output	reg	[(BW-1):0]	o_wb_data;
	// Interrupt line
	output	reg			o_int;
	initial	o_wb_data = 32'h00;
	always @(posedge i_clk)
		if ((i_wb_cyc)&&(i_wb_stb)&&(i_wb_we))
			o_wb_data <= i_wb_data;
		else if (i_ce)
			o_wb_data <= o_wb_data + 1;
	initial	o_int = 0;
	always @(posedge i_clk)
		if (i_ce)
			o_int <= &o_wb_data;
			o_int <= 1'b0;
	initial	o_wb_ack = 1'b0;
	always @(posedge i_clk)
		o_wb_ack <= (i_wb_cyc)&&(i_wb_stb);
	assign	o_wb_stall = 1'b0;

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2022, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.