Rev |
Log message |
Author |
Age |
Path |
102 |
Updated documentation. The documentation for these now also reflects that
these were drawn from an FPGA Library project, that is shared among many
FPGA builds. |
dgisselq |
2972d 10h |
/ |
101 |
Fixed the `defines at the top so that this can be built without any CPU.
This was then used to measure the impact of the CPU on the entire build, as
you could now build with no CPU, and then with a CPU to compare. |
dgisselq |
2972d 10h |
/ |
100 |
Includes updates so this can run at higher clocks speeds within an FPGA. |
dgisselq |
2972d 11h |
/ |
99 |
Includes high-speed updates. rxuart and txuart will now run at 200MHz on
an Artix-7, so should not impact timing (any more) on the XuLA platform. |
dgisselq |
2972d 11h |
/ |
98 |
Updated copyright notices for the new year, to reflect that changes have been
made in 2016. |
dgisselq |
2972d 11h |
/ |
97 |
Latest working bit file, with all changes attached as of this date. |
dgisselq |
2995d 15h |
/ |
96 |
Now accepts an SD-Card backing file, so that SD-Card reads *and* writes can be
tested. |
dgisselq |
2995d 15h |
/ |
95 |
Added write capability to the SD-SPI simulator. |
dgisselq |
2995d 15h |
/ |
94 |
Fixes a bug which had caused the device to die artificially and early, just
simply because the program connecting to the simulator shut its pipe down before
getting our last message. We now ignore this signal and continue. |
dgisselq |
2995d 15h |
/ |
93 |
Oops -- missed adjusting the copyright. |
dgisselq |
2995d 15h |
/ |
92 |
Fixes the problem whereby the master counters show when the user counters should
be showing and vice versa. Now the master counters show by default, together
with their correct labels. User counters are still available by pressing
'u' in the debugger, and the master counter display may be returned to by
pressing 'm' in the debugger. |
dgisselq |
2995d 15h |
/ |
91 |
Fixes bugs associated with an overflow of write acknowledgements in the
receiver. This helps keep our accesses aligned. |
dgisselq |
2995d 15h |
/ |
90 |
Reads and writes to the SD over SPI port now work. The card appears, as of now,
to be fully functional. |
dgisselq |
2995d 15h |
/ |
89 |
Bug fixes, following the adf_ce logic combining ALU/DIVIDE/FPU pipeline logic
into one register, this fixes that logic so that instructions without their
condition fulfilled are still "executed" and marked as done. |
dgisselq |
2995d 15h |
/ |
88 |
Adjusted copyright date. |
dgisselq |
2995d 15h |
/ |
87 |
Placed the interrupt into the carry chain for less logic area. |
dgisselq |
2995d 15h |
/ |
86 |
Fine tuning the `defines, so that you can build pipelined without pipelined
bus access and so forth. |
dgisselq |
2995d 15h |
/ |
85 |
First version of the SD-SPI interface, with partial functionality. (No the
empty link that was here before.) |
dgisselq |
2999d 12h |
/ |
84 |
First part of switching to proper sdspi.v, and not just the link. |
dgisselq |
2999d 12h |
/ |
83 |
Fixes a bug in the LX9 build whereby the flash was never ever granted permission
to use the SPI port. |
dgisselq |
3000d 16h |
/ |
82 |
|
dgisselq |
3001d 11h |
/ |
81 |
Adds register values for the SD-Card registers. |
dgisselq |
3001d 11h |
/ |
80 |
Currently working version: contains both a working DMA controller as well as
a working (as far as I can tell) SD-Card controller (writes not yet tested). |
dgisselq |
3001d 11h |
/ |
79 |
Adds 'bench' and 'sw' targets, and automatically builds them (now). |
dgisselq |
3001d 11h |
/ |
78 |
Comments out the line that caused a compiler warning--setting an unused
variable. Code should be better as a result. |
dgisselq |
3001d 11h |
/ |
77 |
Adds register names and values for the SD card interface. |
dgisselq |
3001d 11h |
/ |
76 |
Now tries to avoid reading from the stack if the stack addresses are already
known to be bad. That way, the debugger tries to preserve any bus error address
already on the buserr device. |
dgisselq |
3001d 11h |
/ |
75 |
Added simulation capability for the SD-Card, as well as debugging output for the
DMA. (The SD-Card debug may not be fully featured, yet, but it has gotten me
to where I can talk to the card.) |
dgisselq |
3001d 11h |
/ |
74 |
Adds the SD-card capability, and connects the debug wires to/from the uartdev
in case it needs to be debugged. |
dgisselq |
3001d 11h |
/ |
73 |
Simplified logic. |
dgisselq |
3001d 11h |
/ |