Rev |
Log message |
Author |
Age |
Path |
32 |
Brought the CPU to its first working version, to include demo. |
dgisselq |
2777d 06h |
/openarty/trunk |
31 |
Initial network is now working. Adding CPU control files to repository. |
dgisselq |
2777d 23h |
/openarty/trunk |
30 |
Network transmit and MIG memory both work now, though the clock speed has
been dropped to 80.125MHz. |
dgisselq |
2777d 23h |
/openarty/trunk |
29 |
Here's the memory pin list, necessary for running Xilinx's Memory Interface
Generator. |
dgisselq |
2805d 19h |
/openarty/trunk |
28 |
Including the updates and corrections from the wbuart32 project. |
dgisselq |
2805d 20h |
/openarty/trunk |
27 |
Bus changes ... |
dgisselq |
2805d 20h |
/openarty/trunk |
26 |
Adjusted the timing comments. |
dgisselq |
2805d 20h |
/openarty/trunk |
25 |
The memory now works. However, the core speed has been lowered to 81.25MHz
to do this. The top level file is no longer fasttop.v, but toplevel.v. |
dgisselq |
2814d 04h |
/openarty/trunk |
24 |
Here are the updates from the first (failed) attempt to try to integrate
the DDR3 SDRAM controller onto this board. |
dgisselq |
2833d 00h |
/openarty/trunk |
23 |
Includes settings necessary for the Arty to load from flash builds, and to
reconfigure itself later. |
dgisselq |
2842d 23h |
/openarty/trunk |
22 |
A useful script for programming the device, given that the current device
program includes a valid comms interface. |
dgisselq |
2842d 23h |
/openarty/trunk |
21 |
Removed the OLED controller one additional clock from the bus. This was
necessary to maintain the 200MHz clock speed, especially given the growing
fanout of the device bus. |
dgisselq |
2842d 23h |
/openarty/trunk |
20 |
Lots of bug fixes: After turning on XIP, and running in XIP mode, leaving XIP
mode turns it back off again, necessitating a new write to the VCon register.
Further, XIP mode starts in extended SPI mode, and only transfers in QSPI
mode for data. Finally, two new commands have been created: enabling the
SPI memory reset, and actually resetting the SPI memory. In general, these
are all better--as the EQSPI flash controller now works with these changes,
whereby it didn't really work without them before. |
dgisselq |
2842d 23h |
/openarty/trunk |
19 |
Creates an LED mask portion of writing to the LED's register. Only those
bits specified in the mask (bits [7:4]) will be adjusted in the LED
register on a write. Hence to set all on, set the LED register to 0x0ff,
all off, 0x0f0, or to set LED 0 to on while leaving the others unchanged,
set it to 0x011. |
dgisselq |
2842d 23h |
/openarty/trunk |
18 |
The device can now program and configure itself, allowing bootstrap possibilities.
` |
dgisselq |
2842d 23h |
/openarty/trunk |
17 |
Fixed the misaddressed I/O peripherals in the fastio peripheral group. In
particular, UART and GPS were misaddressed. This has now been fixed, so these
peripherals (should) match the spec. Further, the default speed of the two
UARTs has been adjusted to 115200/8N1 for the aux UART, and 9600/8N1 for the
GPS UART. The Aux UART transmitter also passes testing, so at least that one
works. |
dgisselq |
2844d 22h |
/openarty/trunk |
16 |
This returns the scope to its original configuration, where the decode()
function is not allowed to have any side effects. |
dgisselq |
2844d 23h |
/openarty/trunk |
15 |
These files were changed/perfected as part of getting the EQSPI flash driver
up and running. They currently match the hardware, as far as I can tell, and
the test bench (_tb.cpp file) shows that the Verilog modules work (with the
simulated hardware) as designed. |
dgisselq |
2845d 00h |
/openarty/trunk |
14 |
All changes made as a part of getting the flash driver up and running. Today,
it successfully programmed a configuration into the Arty via wbprogram, so ...
that's been my last/best test. |
dgisselq |
2845d 00h |
/openarty/trunk |
13 |
Here are the updates necessary to get the initial Quad SPI flash driver working.
This includes in particular the bus interconnect (in fastmaster.v), and the
final hookup to the external wires (in fasttop.v). |
dgisselq |
2845d 00h |
/openarty/trunk |
12 |
A work in progress. This checkin contains fixes for the flash (mostly),
together with some logic reductions facilitating full speed (200MHz) build. |
dgisselq |
2846d 03h |
/openarty/trunk |
11 |
Files necessary to simulate the entire Arty board--everything at the fastmaster
module and below. |
dgisselq |
2846d 03h |
/openarty/trunk |
10 |
Updated flash data and test files, for a flash that produces it's answers a
clock after I'm expecting them. |
dgisselq |
2846d 03h |
/openarty/trunk |
9 |
Adding copywrite statement (oops). |
dgisselq |
2846d 03h |
/openarty/trunk |
8 |
Fixes the makefile so it builds a complete testbench suite, emulating the
entire Arty board. |
dgisselq |
2846d 03h |
/openarty/trunk |
7 |
This implements the coordination of a massive build/test suite--just not the
actual configuration file itself. |
dgisselq |
2846d 03h |
/openarty/trunk |
6 |
Minor updates, mostly to support the development of the DDR3 SDRAM--such
as creating addresses for the debugging scope used to figure out what's
going on with it. |
dgisselq |
2846d 03h |
/openarty/trunk |
5 |
Initial checkin, this time of the bench testing s/w. |
dgisselq |
2861d 06h |
/openarty/trunk |
4 |
Initial host software pack. |
dgisselq |
2861d 06h |
/openarty/trunk |
3 |
Initial set of files. The flash appears to work, memory hasn't been started,
the MDIO controller works in simulation, etc. Everything below fasttop.v works
at 200MHz (not the CPU---yet). |
dgisselq |
2861d 06h |
/openarty/trunk |