Rev |
Log message |
Author |
Age |
Path |
85 |
First version of the SD-SPI interface, with partial functionality. (No the
empty link that was here before.) |
dgisselq |
2954d 07h |
/xulalx25soc/trunk |
84 |
First part of switching to proper sdspi.v, and not just the link. |
dgisselq |
2954d 07h |
/xulalx25soc/trunk |
83 |
Fixes a bug in the LX9 build whereby the flash was never ever granted permission
to use the SPI port. |
dgisselq |
2955d 11h |
/xulalx25soc/trunk |
82 |
|
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
81 |
Adds register values for the SD-Card registers. |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
80 |
Currently working version: contains both a working DMA controller as well as
a working (as far as I can tell) SD-Card controller (writes not yet tested). |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
79 |
Adds 'bench' and 'sw' targets, and automatically builds them (now). |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
78 |
Comments out the line that caused a compiler warning--setting an unused
variable. Code should be better as a result. |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
77 |
Adds register names and values for the SD card interface. |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
76 |
Now tries to avoid reading from the stack if the stack addresses are already
known to be bad. That way, the debugger tries to preserve any bus error address
already on the buserr device. |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
75 |
Added simulation capability for the SD-Card, as well as debugging output for the
DMA. (The SD-Card debug may not be fully featured, yet, but it has gotten me
to where I can talk to the card.) |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
74 |
Adds the SD-card capability, and connects the debug wires to/from the uartdev
in case it needs to be debugged. |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
73 |
Simplified logic. |
dgisselq |
2956d 06h |
/xulalx25soc/trunk |
72 |
Sets XULA25 as the default. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
71 |
Needed to play with subtle timing to get this to build. Expect me to play
with these two clock numbers more. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
70 |
Cosmetic (minor) update. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
69 |
Massive logic simplification. This is also the first (verified) working
version. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
68 |
Fixes the debug ack line, so it no longer acks when there isn't a dbg_stb.
Fixed the multiply option parameter, so it sets a 3-clock multiply properly.
Adjusted the watchdog timer so that it now produces a timer that doesn't
reload--since this is pointless for a watchdog. Finally, connects a reset
line to the DMA, to make certain that resetting the CPU will also reset any
ongoing DMA operation. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
67 |
Simplifies logic, and guarantees that the minimum set value will always
produce an int. For example, if the count was X before, setting X-1 wouldn't
produce an interrupt since it had passed. Now it produces an interrupt, and
keeps the next interrupt valid. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
66 |
Simplified logic (barely). |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
65 |
Makes the auto-reload feature a parameterized (generic) feature, so the same
code will work for both auto-reloadable and non-autoreloadable (i.e. watchdog)
timers. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
64 |
First (verified) working version. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
63 |
Simplified logic. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
62 |
Removed the pipe logic from the non-pipelined version, and made the NOOP a
specific ALU instruction so that the PC is always properly updated. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
61 |
Fixed the timing control wires: busy and valid will never both be true. Busy
will be true (now) until valid is asserted, and busy will never not be
asserted until valid is true. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
60 |
LONG_MPY upgrade. This is part of swapping out the LDIHI instruction for a
MPY, and the MPYS and MPYU instructions for MPYSHI and MPYUHI respectively. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
59 |
Simplified logic. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
58 |
Bug fix: the UART can now be reconfigured post-boot without a BREAK condition. |
dgisselq |
2956d 07h |
/xulalx25soc/trunk |
57 |
Fixed the TX/RX addresses so that they match the documentation: TX first, then
RX. |
dgisselq |
2964d 07h |
/xulalx25soc/trunk |
56 |
Brings code in line with the OpenCores core: parameterizes the reload value,
and the number of bits in the timer. |
dgisselq |
2964d 07h |
/xulalx25soc/trunk |