Rev |
Log message |
Author |
Age |
Path |
116 |
Fixes a compiler warning about signed versus unsigned comparison, by forcing
the comparison to be signed. |
dgisselq |
2984d 17h |
/ |
115 |
Made the SDCard support dependent upon a XULA25 macro, which is defined at the
top of the file. Remove the XULA25 macro definition, and this will build
assuming a XULA9 configuration. |
dgisselq |
2993d 08h |
/ |
114 |
Added ZipBones to the list of dependencies, so this will (should) build
properly for the XULA9 as well as the XULA25. |
dgisselq |
2993d 08h |
/ |
113 |
Lots of updates, mostly focused on getting the XuLA board and CPU able to pass
a comprehensive test suite. At this point, everything passes and logic usage
is down even. Among the few changes includes the "break" bit in the uCC
register, used to indicate a switch to supervisor mode occurred as a result
of a user break, and the ability for the supervisor to clear the instruction
cache. |
dgisselq |
2993d 08h |
/ |
112 |
Provides a simulated UART capability to the busmaster_tb simulation. |
dgisselq |
2995d 13h |
/ |
111 |
Added some debug support programs to the repository. |
dgisselq |
3001d 07h |
/ |
110 |
Fixed a problem whereby block RAM would be declared as a bus error on the
stack, even if the data was valid. |
dgisselq |
3001d 12h |
/ |
109 |
This continues the updates to the wishbone-uart conversion. It fixes several
bugs within wbuexec, and pipelines the compression scheme. Further, the
read codeword was adjusted so that a read of 8 can be requested with six-bits,
rather than requiring 12. Likewise, the dependence upon the read of 8 on
incrementing the address pointer has been removed. All told, the design
builds for a 200MHz Artix-7, and it has been tested with the CMod-S6. (Writing
flash seems to be one of the most comprehensive tests ...) |
dgisselq |
3001d 16h |
/ |
108 |
Minor documentation updates. |
dgisselq |
3002d 02h |
/ |
107 |
Minor change. |
dgisselq |
3002d 02h |
/ |
106 |
Minor, inconsequential changes. |
dgisselq |
3002d 02h |
/ |
105 |
Mostly cosmetic changes. The Makefile now builds a couple more programs,
the documentation is better, etc. |
dgisselq |
3002d 02h |
/ |
104 |
Updates to the flash driver drawn from the S6SoC project. |
dgisselq |
3002d 02h |
/ |
103 |
Added a SDSPI scope, and defined which of the four scopes it points to.
(It uses the configuration scopes position, if the configuration scope isn't
defined.) |
dgisselq |
3002d 02h |
/ |
102 |
Updated documentation. The documentation for these now also reflects that
these were drawn from an FPGA Library project, that is shared among many
FPGA builds. |
dgisselq |
3002d 02h |
/ |
101 |
Fixed the `defines at the top so that this can be built without any CPU.
This was then used to measure the impact of the CPU on the entire build, as
you could now build with no CPU, and then with a CPU to compare. |
dgisselq |
3002d 02h |
/ |
100 |
Includes updates so this can run at higher clocks speeds within an FPGA. |
dgisselq |
3002d 03h |
/ |
99 |
Includes high-speed updates. rxuart and txuart will now run at 200MHz on
an Artix-7, so should not impact timing (any more) on the XuLA platform. |
dgisselq |
3002d 03h |
/ |
98 |
Updated copyright notices for the new year, to reflect that changes have been
made in 2016. |
dgisselq |
3002d 03h |
/ |
97 |
Latest working bit file, with all changes attached as of this date. |
dgisselq |
3025d 06h |
/ |
96 |
Now accepts an SD-Card backing file, so that SD-Card reads *and* writes can be
tested. |
dgisselq |
3025d 06h |
/ |
95 |
Added write capability to the SD-SPI simulator. |
dgisselq |
3025d 07h |
/ |
94 |
Fixes a bug which had caused the device to die artificially and early, just
simply because the program connecting to the simulator shut its pipe down before
getting our last message. We now ignore this signal and continue. |
dgisselq |
3025d 07h |
/ |
93 |
Oops -- missed adjusting the copyright. |
dgisselq |
3025d 07h |
/ |
92 |
Fixes the problem whereby the master counters show when the user counters should
be showing and vice versa. Now the master counters show by default, together
with their correct labels. User counters are still available by pressing
'u' in the debugger, and the master counter display may be returned to by
pressing 'm' in the debugger. |
dgisselq |
3025d 07h |
/ |
91 |
Fixes bugs associated with an overflow of write acknowledgements in the
receiver. This helps keep our accesses aligned. |
dgisselq |
3025d 07h |
/ |
90 |
Reads and writes to the SD over SPI port now work. The card appears, as of now,
to be fully functional. |
dgisselq |
3025d 07h |
/ |
89 |
Bug fixes, following the adf_ce logic combining ALU/DIVIDE/FPU pipeline logic
into one register, this fixes that logic so that instructions without their
condition fulfilled are still "executed" and marked as done. |
dgisselq |
3025d 07h |
/ |
88 |
Adjusted copyright date. |
dgisselq |
3025d 07h |
/ |
87 |
Placed the interrupt into the carry chain for less logic area. |
dgisselq |
3025d 07h |
/ |