Rev |
Log message |
Author |
Age |
Path |
162 |
Tasks don't have parenthesis. This is only used for ports on modules. This was a mistake from my part. |
rfajardo |
4608d 04h |
/minsoc/ |
161 |
Correcting configure parameters of adv_jtag_bridge on installation script. |
rfajardo |
4621d 07h |
/minsoc/ |
160 |
Typo in minsoc-install.sh script. Adv_jtag_bridge was not configuring correctly. |
rfajardo |
4621d 07h |
/minsoc/ |
159 |
Updated constraint file for de2_115 board. (Richard Hasha) |
rfajardo |
4621d 08h |
/minsoc/ |
158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4623d 00h |
/minsoc/ |
157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4628d 19h |
/minsoc/ |
156 |
Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered. |
nyawn |
4628d 19h |
/minsoc/ |
155 |
Decreased wait time, for faster simulations. |
nyawn |
4628d 19h |
/minsoc/ |
154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4628d 19h |
/minsoc/ |
153 |
Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. |
rfajardo |
4661d 08h |
/minsoc/ |
152 |
Roll back to retrieve minsoc from branches/rc-1.0. |
rfajardo |
4661d 08h |
/minsoc/ |
151 |
Creating tag release-1.0 from revision 150 of branches/rc-1.0. |
rfajardo |
4661d 09h |
/minsoc/ |
150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4661d 09h |
/minsoc/ |
149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4661d 09h |
/minsoc/ |
148 |
Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. |
rfajardo |
4666d 05h |
/minsoc/ |
147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4666d 07h |
/minsoc/ |
146 |
Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. |
ConX. |
4666d 13h |
/minsoc/ |
145 |
minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. |
rfajardo |
4666d 22h |
/minsoc/ |
144 |
Updating configure scripts. Calling make into the right directories now. |
rfajardo |
4667d 08h |
/minsoc/ |
143 |
Compiling firmwares in board configuration scripts instead of on global minsoc setup. |
rfajardo |
4667d 08h |
/minsoc/ |
142 |
Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.
backend/xxx/configure: compiling firmwares here now. |
rfajardo |
4667d 08h |
/minsoc/ |
141 |
Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. |
rfajardo |
4667d 08h |
/minsoc/ |
140 |
Including required modules for verilator simulation. |
rfajardo |
4667d 09h |
/minsoc/ |
139 |
Creating a verilator branche. |
rfajardo |
4667d 09h |
/minsoc/ |
138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4667d 22h |
/minsoc/ |
137 |
Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). |
rfajardo |
4668d 09h |
/minsoc/ |
136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4675d 04h |
/minsoc/ |
135 |
Installation on Ubuntu-11.10 has shown that package texinfo is required to compiled GDB. This package installs the binary makeinfo. |
rfajardo |
4675d 04h |
/minsoc/ |
134 |
run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. |
rfajardo |
4682d 08h |
/minsoc/ |
133 |
Roll back minsoc_bench.v to timed simulation. Merge minsoc_bench_core and minsoc_bench_clock again.
Applying Rubén Diez patch to avoid warnings on firmware load for simulation. |
rfajardo |
4682d 09h |
/minsoc/ |