Rev |
Log message |
Author |
Age |
Path |
147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4580d 17h |
/minsoc/branches/rc-1.0/backend/ |
146 |
Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. |
ConX. |
4580d 23h |
/minsoc/branches/rc-1.0/backend/ |
143 |
Compiling firmwares in board configuration scripts instead of on global minsoc setup. |
rfajardo |
4581d 19h |
/minsoc/branches/rc-1.0/backend/ |
137 |
Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). |
rfajardo |
4582d 19h |
/minsoc/branches/rc-1.0/backend/ |
124 |
Removing Verilog delays from minsoc_bench.v. minsoc_bench_defines.v defines now if uart or ethernet have to be tested. If yes, it checks the behavior of the enclosed firmwares. If not, simulation simply runs forever. |
rfajardo |
4601d 14h |
/minsoc/branches/rc-1.0/backend/ |
118 |
Configure scripts for Xilinx devices updated. All of them require to update or1200_defines.v. The non-standard part uses now the variable $BOARD to print that this board require non-standard update of files. |
rfajardo |
4607d 13h |
/minsoc/branches/rc-1.0/backend/ |
117 |
spartan3e_starter_kit designs require DUALPORT from or1200_defines.v to be active instead of GENERIC. |
rfajardo |
4607d 14h |
/minsoc/branches/rc-1.0/backend/ |
116 |
Configure scripts were trying to copy/patch projects files before creating them. Ordering is correct now. |
rfajardo |
4607d 15h |
/minsoc/branches/rc-1.0/backend/ |
113 |
minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error
spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated
prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files |
rfajardo |
4607d 16h |
/minsoc/branches/rc-1.0/backend/ |
110 |
Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure
-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0
-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.
-prj/src: or1200_top.prj downdated to definition of or1200_v1 |
rfajardo |
4608d 08h |
/minsoc/branches/rc-1.0/backend/ |
109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4608d 10h |
/minsoc/branches/rc-1.0/backend/ |
105 |
Updating configure scripts to copy Windows synthesis launch script setup.bat from either minsoc/syn/altera or minsoc/syn/xilinx to minsoc/syn. |
rfajardo |
4608d 20h |
/minsoc/trunk/backend/ |
99 |
backend/altera_3c25_board/minsoc_defines.v: if GENERIC_FPGA selected, undefine ALTERA_FPGA and FPGA_FAMILY to avoid vendor specific code to flow into the simulation. If you don't do it, generate_bench fails. |
rfajardo |
4652d 20h |
/minsoc/trunk/backend/ |
97 |
As proposed by Javier Almansa automatically generated project files for simulation and synthesis are out of revision control. Instead, the backend configure scripts run the prj/Makefile now to generate the project files prior to configuration of SoC for a specific board. |
rfajardo |
4652d 21h |
/minsoc/trunk/backend/ |
96 |
Some files needed for Altera synthesis |
javieralso |
4653d 07h |
/minsoc/trunk/backend/ |
95 |
Makefile for Altera FPGAs fixed |
javieralso |
4654d 10h |
/minsoc/trunk/backend/ |
93 |
Support for Altera synthesis. It needs some tune, but it works fine |
javieralso |
4656d 22h |
/minsoc/trunk/backend/ |
92 |
backend/spartan3e_starter_kit*: or1200_defines.v file was outdated and hindering synthesis. Probably it would be best if we used a patching system here. But for now, I copied the new files and made the necessary changes to fit the system into the target boards. |
rfajardo |
4657d 20h |
/minsoc/trunk/backend/ |
88 |
Project structure, Xilinx Makefiles and simulation working. |
rfajardo |
4658d 13h |
/minsoc/trunk/backend/ |
87 |
Synchronizing scripts to behave exactly the same. |
rfajardo |
4658d 14h |
/minsoc/trunk/backend/ |
86 |
Updating configure script messages. |
rfajardo |
4658d 14h |
/minsoc/trunk/backend/ |
85 |
Central project definition under prj. Synthesis and simulation take their project files from here. |
rfajardo |
4658d 14h |
/minsoc/trunk/backend/ |
80 |
Establishing a better Makefile system for firmwares. |
rfajardo |
4676d 18h |
/minsoc/trunk/backend/ |
70 |
Including a global timescale under minsoc/rtl/verilog to control simulation. It is under the implementation because the implementation files include it.
Removing timescale definition of minsoc_bench_defines.v files.
Creating a modelsim simulation directory. Everything is working under Linux. For Windows, run_sim.sh has to be changed:
-pli ../../bench/verilog/vpi/jp-io-vpi.so
to:
-pli ../../bench/verilog/vpi/jp-io-vpi.dll
These files have to be compiled/copied from minsoc/rtl/verilog/adv_debug_sys/Software/adv_jtag_bridge/sim_lib/modelsim_platform to minsoc/bench/verilog/vpi. |
rfajardo |
4777d 19h |
/minsoc/trunk/backend/ |
69 |
backend update:
-minsoc_bench_defines.v
-gcc-opt.mk
Both files should now be under minsoc/backend to proper system functionality.
backend subdirectories have been given those files. Configure script updated accordingly.
They are searched there from system scripts and Makefiles.
-sim/bin/minsoc_verilog_files.txt has the files for Icarus Verilog, minsoc_bench_defines.v is now referenced from backend directory.
-sw/support/Makefile.inc now references to gcc-opt.mk inside backend.
backend/spartan3e_starter_kit_eth:
-It is the system configuration for Spartan 3E Starter Kit with Ethernet. |
rfajardo |
4782d 11h |
/minsoc/trunk/backend/ |
68 |
Still one configuration mismatch on minsoc_defines.v:
-MEMORY_ADR_WIDTH now 15
-orp.ld is defined accordingly |
rfajardo |
4784d 15h |
/minsoc/trunk/backend/ |
67 |
Constraint file for backend spartan3a_dsp_kit.ucf was configured to include the STARTUP module.
This module is not enabled under the respective minsoc_defines.v. Thus, its pins had to be commented out. |
rfajardo |
4784d 15h |
/minsoc/trunk/backend/ |
66 |
spartan3e_starter_kit requires special configuration of or1200_r3.
For that, configure script was specially adapted and that is reported on script execution.
For release-1.0 of MinSoC this should not be required, because or1200_r1 already has the
required configuration. |
rfajardo |
4784d 16h |
/minsoc/trunk/backend/ |
65 |
Files missing in the last commit.
backend/std/configure
sw: eth, uart and driver Makefiles |
rfajardo |
4784d 17h |
/minsoc/trunk/backend/ |
64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4784d 19h |
/minsoc/trunk/backend/ |