| Rev |
Log message |
Author |
Age |
Path |
| 35 |
Added comments and copyright notice. |
dgisselq |
2786d 13h |
/openarty/trunk/ |
| 34 |
These updates bring the distribution along to the point where both the GPS
clock subsecond tracking, as well as the OLEDrgb controller now work. |
dgisselq |
2786d 15h |
/openarty/trunk/ |
| 33 |
Fixed the network receive CRC and MAC checking, and added ip-checking and
minimum packet length checking to the receiver. |
dgisselq |
2791d 21h |
/openarty/trunk/ |
| 32 |
Brought the CPU to its first working version, to include demo. |
dgisselq |
2793d 00h |
/openarty/trunk/ |
| 31 |
Initial network is now working. Adding CPU control files to repository. |
dgisselq |
2793d 17h |
/openarty/trunk/ |
| 30 |
Network transmit and MIG memory both work now, though the clock speed has
been dropped to 80.125MHz. |
dgisselq |
2793d 17h |
/openarty/trunk/ |
| 29 |
Here's the memory pin list, necessary for running Xilinx's Memory Interface
Generator. |
dgisselq |
2821d 13h |
/openarty/trunk/ |
| 28 |
Including the updates and corrections from the wbuart32 project. |
dgisselq |
2821d 14h |
/openarty/trunk/ |
| 27 |
Bus changes ... |
dgisselq |
2821d 14h |
/openarty/trunk/ |
| 26 |
Adjusted the timing comments. |
dgisselq |
2821d 14h |
/openarty/trunk/ |
| 25 |
The memory now works. However, the core speed has been lowered to 81.25MHz
to do this. The top level file is no longer fasttop.v, but toplevel.v. |
dgisselq |
2829d 22h |
/openarty/trunk/ |
| 24 |
Here are the updates from the first (failed) attempt to try to integrate
the DDR3 SDRAM controller onto this board. |
dgisselq |
2848d 17h |
/openarty/trunk/ |
| 23 |
Includes settings necessary for the Arty to load from flash builds, and to
reconfigure itself later. |
dgisselq |
2858d 17h |
/openarty/trunk/ |
| 22 |
A useful script for programming the device, given that the current device
program includes a valid comms interface. |
dgisselq |
2858d 17h |
/openarty/trunk/ |
| 21 |
Removed the OLED controller one additional clock from the bus. This was
necessary to maintain the 200MHz clock speed, especially given the growing
fanout of the device bus. |
dgisselq |
2858d 17h |
/openarty/trunk/ |
| 20 |
Lots of bug fixes: After turning on XIP, and running in XIP mode, leaving XIP
mode turns it back off again, necessitating a new write to the VCon register.
Further, XIP mode starts in extended SPI mode, and only transfers in QSPI
mode for data. Finally, two new commands have been created: enabling the
SPI memory reset, and actually resetting the SPI memory. In general, these
are all better--as the EQSPI flash controller now works with these changes,
whereby it didn't really work without them before. |
dgisselq |
2858d 17h |
/openarty/trunk/ |
| 19 |
Creates an LED mask portion of writing to the LED's register. Only those
bits specified in the mask (bits [7:4]) will be adjusted in the LED
register on a write. Hence to set all on, set the LED register to 0x0ff,
all off, 0x0f0, or to set LED 0 to on while leaving the others unchanged,
set it to 0x011. |
dgisselq |
2858d 17h |
/openarty/trunk/ |
| 18 |
The device can now program and configure itself, allowing bootstrap possibilities.
` |
dgisselq |
2858d 17h |
/openarty/trunk/ |
| 17 |
Fixed the misaddressed I/O peripherals in the fastio peripheral group. In
particular, UART and GPS were misaddressed. This has now been fixed, so these
peripherals (should) match the spec. Further, the default speed of the two
UARTs has been adjusted to 115200/8N1 for the aux UART, and 9600/8N1 for the
GPS UART. The Aux UART transmitter also passes testing, so at least that one
works. |
dgisselq |
2860d 16h |
/openarty/trunk/ |
| 16 |
This returns the scope to its original configuration, where the decode()
function is not allowed to have any side effects. |
dgisselq |
2860d 17h |
/openarty/trunk/ |
| 15 |
These files were changed/perfected as part of getting the EQSPI flash driver
up and running. They currently match the hardware, as far as I can tell, and
the test bench (_tb.cpp file) shows that the Verilog modules work (with the
simulated hardware) as designed. |
dgisselq |
2860d 17h |
/openarty/trunk/ |
| 14 |
All changes made as a part of getting the flash driver up and running. Today,
it successfully programmed a configuration into the Arty via wbprogram, so ...
that's been my last/best test. |
dgisselq |
2860d 17h |
/openarty/trunk/ |
| 13 |
Here are the updates necessary to get the initial Quad SPI flash driver working.
This includes in particular the bus interconnect (in fastmaster.v), and the
final hookup to the external wires (in fasttop.v). |
dgisselq |
2860d 18h |
/openarty/trunk/ |
| 12 |
A work in progress. This checkin contains fixes for the flash (mostly),
together with some logic reductions facilitating full speed (200MHz) build. |
dgisselq |
2861d 20h |
/openarty/trunk/ |
| 11 |
Files necessary to simulate the entire Arty board--everything at the fastmaster
module and below. |
dgisselq |
2861d 20h |
/openarty/trunk/ |
| 10 |
Updated flash data and test files, for a flash that produces it's answers a
clock after I'm expecting them. |
dgisselq |
2861d 20h |
/openarty/trunk/ |
| 9 |
Adding copywrite statement (oops). |
dgisselq |
2861d 20h |
/openarty/trunk/ |
| 8 |
Fixes the makefile so it builds a complete testbench suite, emulating the
entire Arty board. |
dgisselq |
2861d 20h |
/openarty/trunk/ |
| 7 |
This implements the coordination of a massive build/test suite--just not the
actual configuration file itself. |
dgisselq |
2861d 20h |
/openarty/trunk/ |
| 6 |
Minor updates, mostly to support the development of the DDR3 SDRAM--such
as creating addresses for the debugging scope used to figure out what's
going on with it. |
dgisselq |
2861d 20h |
/openarty/trunk/ |
