Rev |
Log message |
Author |
Age |
Path |
78 |
Comments out the line that caused a compiler warning--setting an unused
variable. Code should be better as a result. |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
77 |
Adds register names and values for the SD card interface. |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
76 |
Now tries to avoid reading from the stack if the stack addresses are already
known to be bad. That way, the debugger tries to preserve any bus error address
already on the buserr device. |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
75 |
Added simulation capability for the SD-Card, as well as debugging output for the
DMA. (The SD-Card debug may not be fully featured, yet, but it has gotten me
to where I can talk to the card.) |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
74 |
Adds the SD-card capability, and connects the debug wires to/from the uartdev
in case it needs to be debugged. |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
73 |
Simplified logic. |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
72 |
Sets XULA25 as the default. |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
71 |
Needed to play with subtle timing to get this to build. Expect me to play
with these two clock numbers more. |
dgisselq |
2970d 19h |
/xulalx25soc/trunk/ |
70 |
Cosmetic (minor) update. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
69 |
Massive logic simplification. This is also the first (verified) working
version. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
68 |
Fixes the debug ack line, so it no longer acks when there isn't a dbg_stb.
Fixed the multiply option parameter, so it sets a 3-clock multiply properly.
Adjusted the watchdog timer so that it now produces a timer that doesn't
reload--since this is pointless for a watchdog. Finally, connects a reset
line to the DMA, to make certain that resetting the CPU will also reset any
ongoing DMA operation. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
67 |
Simplifies logic, and guarantees that the minimum set value will always
produce an int. For example, if the count was X before, setting X-1 wouldn't
produce an interrupt since it had passed. Now it produces an interrupt, and
keeps the next interrupt valid. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
66 |
Simplified logic (barely). |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
65 |
Makes the auto-reload feature a parameterized (generic) feature, so the same
code will work for both auto-reloadable and non-autoreloadable (i.e. watchdog)
timers. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
64 |
First (verified) working version. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
63 |
Simplified logic. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
62 |
Removed the pipe logic from the non-pipelined version, and made the NOOP a
specific ALU instruction so that the PC is always properly updated. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
61 |
Fixed the timing control wires: busy and valid will never both be true. Busy
will be true (now) until valid is asserted, and busy will never not be
asserted until valid is true. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
60 |
LONG_MPY upgrade. This is part of swapping out the LDIHI instruction for a
MPY, and the MPYS and MPYU instructions for MPYSHI and MPYUHI respectively. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
59 |
Simplified logic. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
58 |
Bug fix: the UART can now be reconfigured post-boot without a BREAK condition. |
dgisselq |
2970d 20h |
/xulalx25soc/trunk/ |
57 |
Fixed the TX/RX addresses so that they match the documentation: TX first, then
RX. |
dgisselq |
2978d 20h |
/xulalx25soc/trunk/ |
56 |
Brings code in line with the OpenCores core: parameterizes the reload value,
and the number of bits in the timer. |
dgisselq |
2978d 20h |
/xulalx25soc/trunk/ |
55 |
Updated copyright notice. |
dgisselq |
2978d 20h |
/xulalx25soc/trunk/ |
54 |
Updated copyright notice. |
dgisselq |
2978d 20h |
/xulalx25soc/trunk/ |
53 |
Added a touch of error checking. |
dgisselq |
3018d 20h |
/xulalx25soc/trunk/ |
52 |
This brings the XuLA2-LX25 SoC up to speed with the rest of the ZipCPU, and
prepares it for the 32x32 bit multiply instruction set change. |
dgisselq |
3018d 20h |
/xulalx25soc/trunk/ |
51 |
Lots of bug fixes. The ugliest were in the prefetch cache, where instructions
from one cache line were being issued as valid in another. Other fixes include
pipeline fixes so that LOD (Rx),Rx; LOD(Rx),Rx works, and more. Finally, the
decode was adjusted so that brev no longer affects the flags. |
dgisselq |
3028d 19h |
/xulalx25soc/trunk/ |
50 |
Updates to fix some broken early branching code, both in idecode and pfcache. |
dgisselq |
3037d 21h |
/xulalx25soc/trunk/ |
49 |
Added some documentation to make the read and write calls easier to understand. |
dgisselq |
3046d 21h |
/xulalx25soc/trunk/ |