Rev |
Log message |
Author |
Age |
Path |
21 |
Changed the top entity for KC705, so that the FADE core is correctly reset
by the RESETMAC command.
Changed sending of the FCMD_RESET command form driver to the FPGA (as it
is not confirmed - the reinitialized core can't confirm the command).
Changed the receiver2t demo program so that it sends RESETMAC three times
before the transmission is started.
In the future, probably there should be a STATUS ioctl, which would
verify, that the core has been reset by RESETMAC.
Then the program should send RESETMAC, and afterwards read the STATUS,
verifying, that RESETMAC arrived FPGA. If not it should repeat the
above procedure (not implemented yet). |
wzab |
3587d 07h |
/ |
20 |
Cured problem with dta_eod missed, when buffer was full at the moment
when dta_eod was asserted.
It caused the client program to hang, as no end of data was transmitted
and no new data arrived... |
wzab |
3587d 22h |
/ |
19 |
The send_cmd function protected to attempt to call it if the Ethernet device was not
claimed before (previously it caused a problem with NULL pointer dereference
in the ioctl in kernel code).
Moved the Ethernet device name to a macro, so it is easier to modify it, when
someone tests in different machines (e.g. the 10Gb/s NIC for tests with
KC705 is p4p1, while 1Gb/s NIC for tests with Atlys is eth0) |
wzab |
3588d 00h |
/ |
18 |
Changed handling of commands so, that all commands are now confirmed - even start and stop
(which previously were not confirmed - successful reception of start was confirmed
by sending of data packets (what if there was no data at the moment?), successful
reception of stop was confirmed by end of data stream).
Added also flushing of data stream after reception of stop command.
The receiver2t.c implements suggested method of communication with the FADE driver.
One thread is responsible for reception and processing of data, while another thread
is responsible for sending of control commands. |
wzab |
3588d 20h |
/ |
17 |
Corrected mutex management in ioctl. |
wzab |
3595d 00h |
/ |
16 |
Introduced inline functions simplifying reading and writing of packets' contents. |
wzab |
3595d 01h |
/ |
15 |
The previous experimental implemenation for 10Gb/s links has been replaced with the
new, rewritten implementation, which uses sequential numbering of packets instaed
of "sets of packets". This allowed to simplify the driver, and improve its performance.
Additionally a possibility to send user defined commands to the FPGA was added. |
wzab |
3602d 22h |
/ |
14 |
Removed small mistake causing a combinatorial loop. |
wzab |
3608d 00h |
/ |
13 |
Small correction in the kernel driver |
wzab |
3610d 06h |
/ |
12 |
Added experimental version of my protocol, working with the 10Gb/s
link on the KC705 board.
The design has been initially tested, and is working, but it still
needs some improvments.
Please note, that this version uses the "jumbo" frames,
with 8192 bytes of user data in each packet (plus header).
Therefore it was necessary to make some changes in the kernel
driver. |
wzab |
3617d 02h |
/ |
11 |
Corrected small bug in eth_sender8 (which in fact should only
generate a compiler warning, as the resulting bit vector
was anyway correctly truncated...) |
wzab |
3774d 00h |
/ |
10 |
Updated test client program - receiver2.c
Added possibility to activate only selected slave in the command line.
Currently program services up to three slaves: 0, 1 and 2
To activate a slave, add its number as a program argument in the command line
(order doesn't matter). |
wzab |
4073d 22h |
/ |
9 |
Corrected serious bug in acknowledged packed number calculations, which lead to transmission
errors in high speed CPUs. |
wzab |
4074d 22h |
/ |
8 |
Adjusted parameters of the NCA (network congestion avoidance) alogorithm
to obtain higher throughput. |
wzab |
4078d 23h |
/ |
7 |
Shortened synchronization path for tx_start signal in the eth_sender blocks |
wzab |
4079d 02h |
/ |
6 |
Further adjusted IFG lengths |
wzab |
4079d 09h |
/ |
5 |
Decreased length of the intraframe gaps (IFG)
In 100Mb/s version - to 100bits (25 nibbles)
In 1Gb/s version - to 104bits (13 bytes) |
wzab |
4079d 23h |
/ |
4 |
Added lacking files PCK_CRC32_D4.vhd and PCK_CRC32_D8.vhd |
wzab |
4106d 07h |
/ |
3 |
Added new version of the FPGA firmware, which does not rely on the Ethernet MAC core.
Now both versions are available.
The version with Ethernet MAC is in directory FPGA_with_MAC.
The version which handles directly Ethernet PHY is in directory FPGA_no_MAC |
wzab |
4106d 08h |
/ |
2 |
Initial submission of the implementation of the "fade" protocol. |
wzab |
4263d 02h |
/ |