Rev |
Log message |
Author |
Age |
Path |
20 |
Cured problem with dta_eod missed, when buffer was full at the moment
when dta_eod was asserted.
It caused the client program to hang, as no end of data was transmitted
and no new data arrived... |
wzab |
3538d 00h |
/ |
19 |
The send_cmd function protected to attempt to call it if the Ethernet device was not
claimed before (previously it caused a problem with NULL pointer dereference
in the ioctl in kernel code).
Moved the Ethernet device name to a macro, so it is easier to modify it, when
someone tests in different machines (e.g. the 10Gb/s NIC for tests with
KC705 is p4p1, while 1Gb/s NIC for tests with Atlys is eth0) |
wzab |
3538d 02h |
/ |
18 |
Changed handling of commands so, that all commands are now confirmed - even start and stop
(which previously were not confirmed - successful reception of start was confirmed
by sending of data packets (what if there was no data at the moment?), successful
reception of stop was confirmed by end of data stream).
Added also flushing of data stream after reception of stop command.
The receiver2t.c implements suggested method of communication with the FADE driver.
One thread is responsible for reception and processing of data, while another thread
is responsible for sending of control commands. |
wzab |
3538d 21h |
/ |
17 |
Corrected mutex management in ioctl. |
wzab |
3545d 02h |
/ |
16 |
Introduced inline functions simplifying reading and writing of packets' contents. |
wzab |
3545d 03h |
/ |
15 |
The previous experimental implemenation for 10Gb/s links has been replaced with the
new, rewritten implementation, which uses sequential numbering of packets instaed
of "sets of packets". This allowed to simplify the driver, and improve its performance.
Additionally a possibility to send user defined commands to the FPGA was added. |
wzab |
3553d 00h |
/ |
14 |
Removed small mistake causing a combinatorial loop. |
wzab |
3558d 02h |
/ |
13 |
Small correction in the kernel driver |
wzab |
3560d 07h |
/ |
12 |
Added experimental version of my protocol, working with the 10Gb/s
link on the KC705 board.
The design has been initially tested, and is working, but it still
needs some improvments.
Please note, that this version uses the "jumbo" frames,
with 8192 bytes of user data in each packet (plus header).
Therefore it was necessary to make some changes in the kernel
driver. |
wzab |
3567d 04h |
/ |
11 |
Corrected small bug in eth_sender8 (which in fact should only
generate a compiler warning, as the resulting bit vector
was anyway correctly truncated...) |
wzab |
3724d 02h |
/ |
10 |
Updated test client program - receiver2.c
Added possibility to activate only selected slave in the command line.
Currently program services up to three slaves: 0, 1 and 2
To activate a slave, add its number as a program argument in the command line
(order doesn't matter). |
wzab |
4024d 00h |
/ |
9 |
Corrected serious bug in acknowledged packed number calculations, which lead to transmission
errors in high speed CPUs. |
wzab |
4025d 00h |
/ |
8 |
Adjusted parameters of the NCA (network congestion avoidance) alogorithm
to obtain higher throughput. |
wzab |
4029d 01h |
/ |
7 |
Shortened synchronization path for tx_start signal in the eth_sender blocks |
wzab |
4029d 04h |
/ |
6 |
Further adjusted IFG lengths |
wzab |
4029d 10h |
/ |
5 |
Decreased length of the intraframe gaps (IFG)
In 100Mb/s version - to 100bits (25 nibbles)
In 1Gb/s version - to 104bits (13 bytes) |
wzab |
4030d 01h |
/ |
4 |
Added lacking files PCK_CRC32_D4.vhd and PCK_CRC32_D8.vhd |
wzab |
4056d 09h |
/ |
3 |
Added new version of the FPGA firmware, which does not rely on the Ethernet MAC core.
Now both versions are available.
The version with Ethernet MAC is in directory FPGA_with_MAC.
The version which handles directly Ethernet PHY is in directory FPGA_no_MAC |
wzab |
4056d 09h |
/ |
2 |
Initial submission of the implementation of the "fade" protocol. |
wzab |
4213d 03h |
/ |
1 |
The project and the structure was created |
root |
4213d 06h |
/ |