Rev |
Log message |
Author |
Age |
Path |
19 |
Creates an LED mask portion of writing to the LED's register. Only those
bits specified in the mask (bits [7:4]) will be adjusted in the LED
register on a write. Hence to set all on, set the LED register to 0x0ff,
all off, 0x0f0, or to set LED 0 to on while leaving the others unchanged,
set it to 0x011. |
dgisselq |
2988d 05h |
/openarty |
18 |
The device can now program and configure itself, allowing bootstrap possibilities.
` |
dgisselq |
2988d 05h |
/openarty |
17 |
Fixed the misaddressed I/O peripherals in the fastio peripheral group. In
particular, UART and GPS were misaddressed. This has now been fixed, so these
peripherals (should) match the spec. Further, the default speed of the two
UARTs has been adjusted to 115200/8N1 for the aux UART, and 9600/8N1 for the
GPS UART. The Aux UART transmitter also passes testing, so at least that one
works. |
dgisselq |
2990d 05h |
/openarty |
16 |
This returns the scope to its original configuration, where the decode()
function is not allowed to have any side effects. |
dgisselq |
2990d 05h |
/openarty |
15 |
These files were changed/perfected as part of getting the EQSPI flash driver
up and running. They currently match the hardware, as far as I can tell, and
the test bench (_tb.cpp file) shows that the Verilog modules work (with the
simulated hardware) as designed. |
dgisselq |
2990d 06h |
/openarty |
14 |
All changes made as a part of getting the flash driver up and running. Today,
it successfully programmed a configuration into the Arty via wbprogram, so ...
that's been my last/best test. |
dgisselq |
2990d 06h |
/openarty |
13 |
Here are the updates necessary to get the initial Quad SPI flash driver working.
This includes in particular the bus interconnect (in fastmaster.v), and the
final hookup to the external wires (in fasttop.v). |
dgisselq |
2990d 06h |
/openarty |
12 |
A work in progress. This checkin contains fixes for the flash (mostly),
together with some logic reductions facilitating full speed (200MHz) build. |
dgisselq |
2991d 09h |
/openarty |
11 |
Files necessary to simulate the entire Arty board--everything at the fastmaster
module and below. |
dgisselq |
2991d 09h |
/openarty |
10 |
Updated flash data and test files, for a flash that produces it's answers a
clock after I'm expecting them. |
dgisselq |
2991d 09h |
/openarty |
9 |
Adding copywrite statement (oops). |
dgisselq |
2991d 09h |
/openarty |
8 |
Fixes the makefile so it builds a complete testbench suite, emulating the
entire Arty board. |
dgisselq |
2991d 09h |
/openarty |
7 |
This implements the coordination of a massive build/test suite--just not the
actual configuration file itself. |
dgisselq |
2991d 09h |
/openarty |
6 |
Minor updates, mostly to support the development of the DDR3 SDRAM--such
as creating addresses for the debugging scope used to figure out what's
going on with it. |
dgisselq |
2991d 09h |
/openarty |
5 |
Initial checkin, this time of the bench testing s/w. |
dgisselq |
3006d 12h |
/openarty |
4 |
Initial host software pack. |
dgisselq |
3006d 12h |
/openarty |
3 |
Initial set of files. The flash appears to work, memory hasn't been started,
the MDIO controller works in simulation, etc. Everything below fasttop.v works
at 200MHz (not the CPU---yet). |
dgisselq |
3006d 13h |
/openarty |
2 |
Initial documentation/proposed specification. (I'm writing the spec as I'm
building the core.) |
dgisselq |
3007d 07h |
/openarty |
1 |
The project and the structure was created |
root |
3007d 11h |
/openarty |