Rev |
Log message |
Author |
Age |
Path |
1308 |
Gyorgy Jeney: extensive cleanup |
phoenix |
7284d 18h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
1244 |
Added "cm" command to copy data inside memory.
Make or1ksim work on little endian platforms.
Port to Mac OS X.
Some bugfixes.
Allow JTAG write access to read-only memory regions. |
hpanther |
7452d 03h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
1165 |
timeout bug fixed; contribution by Carlos |
markom |
7691d 02h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
1153 |
When multiple interrupts were pending, e.g. TX buffer empty and RX
available, reading the UART's IIR register could potentially clear a
TX interrupt before it had been sent to the processor, thus dropping
the interrupt permanently.
Fix tested w/ both eCos and uclinux. |
sfurman |
7748d 21h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
1145 |
1) Fix trivial bug w/ transmitter empty interrupts that I introduced in the
last check-in.
2) Improve printed output from debugging-only uart_status() routine. |
sfurman |
7749d 15h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
1143 |
Make UART transmitter-empty interrupts match both 16450 and 16550 behavior. |
sfurman |
7752d 11h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
1116 |
There was a bug in the simulator's UART implementation that caused the
UART's LSR register to become corrupted. This was due to an
assumption that 'char' is an unsigned type, but that is not true on
all platforms.
When the char type is signed and a character is read in the range
0x80-0xff, the high bit is sign-extended into the upper bits of an
entry in the receive FIFO. When the character reaches the head of the
FIFO, the upper bits of the FIFO entry are OR'ed into the LSR, causing
the LSR to be set to 0xFF.
A simple cast fixes the problem. |
sfurman |
7792d 19h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
1073 |
channels support |
rprescott |
7917d 23h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
997 |
PRINTF should be used instead of printf; command redirection repaired |
markom |
7981d 09h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
970 |
Testbench is now running on ORP architecture platform. |
simons |
7988d 20h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
884 |
code cleaning - a lot of global variables moved to runtime struct |
markom |
8025d 07h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
821 |
ugly bug with duplicate redefined i removed |
markom |
8111d 03h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
806 |
uart now partially uses scheduler |
markom |
8116d 10h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
805 |
kbd, fb, vga devices now uses scheduler |
markom |
8116d 10h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
713 |
lot of small minor improvements: code documented, cleaned; runs at about same speed when not actually logging, but exe_log is enabled; raw_stats now run only with simple execution - enable RAW_USAGE_STATS macro |
markom |
8153d 08h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
549 |
enabled parameters removed from devices, which also have number of devices; command line --output-cfg parameter added |
markom |
8207d 04h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
530 |
THRI interrupt fixed. |
simons |
8209d 21h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
529 |
Bug in receiver fixed. |
simons |
8209d 23h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
492 |
uart THRE interrupt immedialty after write to IER |
markom |
8226d 07h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |
490 |
clkcycle parsing problem fixed |
markom |
8227d 03h |
/or1k/tags/stable_0_1_0/or1ksim/peripheral/16450.c |