Rev |
Log message |
Author |
Age |
Path |
1244 |
Added "cm" command to copy data inside memory.
Make or1ksim work on little endian platforms.
Port to Mac OS X.
Some bugfixes.
Allow JTAG write access to read-only memory regions. |
hpanther |
7469d 23h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
1165 |
timeout bug fixed; contribution by Carlos |
markom |
7708d 22h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
1153 |
When multiple interrupts were pending, e.g. TX buffer empty and RX
available, reading the UART's IIR register could potentially clear a
TX interrupt before it had been sent to the processor, thus dropping
the interrupt permanently.
Fix tested w/ both eCos and uclinux. |
sfurman |
7766d 17h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
1145 |
1) Fix trivial bug w/ transmitter empty interrupts that I introduced in the
last check-in.
2) Improve printed output from debugging-only uart_status() routine. |
sfurman |
7767d 11h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
1143 |
Make UART transmitter-empty interrupts match both 16450 and 16550 behavior. |
sfurman |
7770d 08h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
1116 |
There was a bug in the simulator's UART implementation that caused the
UART's LSR register to become corrupted. This was due to an
assumption that 'char' is an unsigned type, but that is not true on
all platforms.
When the char type is signed and a character is read in the range
0x80-0xff, the high bit is sign-extended into the upper bits of an
entry in the receive FIFO. When the character reaches the head of the
FIFO, the upper bits of the FIFO entry are OR'ed into the LSR, causing
the LSR to be set to 0xFF.
A simple cast fixes the problem. |
sfurman |
7810d 15h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
1073 |
channels support |
rprescott |
7935d 19h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
997 |
PRINTF should be used instead of printf; command redirection repaired |
markom |
7999d 05h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
970 |
Testbench is now running on ORP architecture platform. |
simons |
8006d 16h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
884 |
code cleaning - a lot of global variables moved to runtime struct |
markom |
8043d 03h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
821 |
ugly bug with duplicate redefined i removed |
markom |
8129d 00h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
806 |
uart now partially uses scheduler |
markom |
8134d 06h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
805 |
kbd, fb, vga devices now uses scheduler |
markom |
8134d 07h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
713 |
lot of small minor improvements: code documented, cleaned; runs at about same speed when not actually logging, but exe_log is enabled; raw_stats now run only with simple execution - enable RAW_USAGE_STATS macro |
markom |
8171d 04h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
549 |
enabled parameters removed from devices, which also have number of devices; command line --output-cfg parameter added |
markom |
8225d 00h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
530 |
THRI interrupt fixed. |
simons |
8227d 18h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
529 |
Bug in receiver fixed. |
simons |
8227d 20h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
492 |
uart THRE interrupt immedialty after write to IER |
markom |
8244d 04h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
490 |
clkcycle parsing problem fixed |
markom |
8244d 23h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |
424 |
memory configuration file joined into .cfg file; *mem.cfg are obsolete; read-only and write-only memory is supported; memory logging is not yet supported; update of testbench - only cache test fails, since it writes to RO memory |
markom |
8254d 03h |
/or1k/tags/stable_0_2_0_rc2/or1ksim/peripheral/16450.c |