| Rev |
Log message |
Author |
Age |
Path |
| 203 |
Removed an extra delay FF from the bitclock rising edge signal for the clock slave configuration to better center the rising edge pulse on the receive signal. |
jshamlet |
1586d 02h |
/ |
| 202 |
Fixed receiver bug that caused false flag detection,
Split the large sdlc_serial_ctrl entity into sub-entities to make debugging easier. |
jshamlet |
1586d 03h |
/ |
| 201 |
Fixed comments regarding RX Checksum location |
jshamlet |
1588d 00h |
/ |
| 200 |
Renamed dual-port buffer to match other entities. |
jshamlet |
1588d 01h |
/ |
| 199 |
Added monitor ram for debugging and fixed issue with dual-port read path. |
jshamlet |
1588d 01h |
/ |
| 198 |
Removed debugging memory |
jshamlet |
1588d 09h |
/ |
| 197 |
Fixed incorrect comments |
jshamlet |
1588d 09h |
/ |
| 196 |
Modified the update logic to allow direct writes to offset 0xFE for refreshing the clock status. This way, any write to the clock status register will immediately be undone. (Writing 0x00 to offset 0xFF is once-more ignored) |
jshamlet |
1588d 10h |
/ |
| 195 |
Added dual-port RAM core for SDLC interface. |
jshamlet |
1589d 04h |
/ |
| 194 |
Cleaned up licensing sections |
jshamlet |
1589d 04h |
/ |
| 193 |
Fixed incorrect comment in o8_alu16.vhd. The value of the write to 0x1F doesn't matter, as the write itself triggers the calculation. |
jshamlet |
1589d 05h |
/ |
| 192 |
Added SDLC packet engine |
jshamlet |
1589d 05h |
/ |
| 191 |
Cleaned up comments, added back the OPEN8_NULLBUS constant, and added some new modules for ADCs and LCD displays.
Also made the button input module more configurable by moving the debounce code to a separate entity and using generics to instantiate it. |
jshamlet |
1589d 05h |
/ |
| 190 |
Fixed a bug in CPU where RTI/RTS wasn't idling the instruction cache, causing intermittent failures where RTI would execute as RTS, corrupting the stack;
Fixed a bug in the real-time clock where the uSec tick generator would stop if the PIT timer value was left/set to 0x00. |
jshamlet |
1601d 03h |
/ |
| 189 |
Merged changes from private repository,
added ceil_log2 function to Open8_pkg, since it is used to calculate RAM vectors,
cleaned up comments and removed local copies of the ceil_log2 function from peripherals. |
jshamlet |
1602d 03h |
/ |
| 188 |
Added a generic to alter the behavior of RTI so that it can optionally skip restoring the general purpose flags GP4 to GP7, allowing ISR's to make persistent changes to them. Also exported these flags to the top level for use outside the CPU. |
jshamlet |
1602d 06h |
/ |
| 187 |
Added the CPU_Halt input, only now as an input to the instruction decoder. The CPU_Halt line will assert the registered CPU_Halt_Req, which will cause the instruction decoder to abort the current instruction, reset the PC, then enter a hold state until the line is deasserted. Additionally, a very minor bug that could cause the SMSK instruction to effectively execute twice if interrupted was fixed. Lastly, cleaned up the comments even more. |
jshamlet |
1604d 02h |
/ |
| 186 |
Merged the interrupt override logic into the case structure, simplifying how interrupts are processed. |
jshamlet |
1607d 02h |
/ |
| 185 |
1) Fixed an apparently long-standing bug where the interrupt bit wasn't being cleared after an RTI
2) Modified the program counter logic to be simpler. It now always increments, and states control the increment using the offset field. A new set of constants was added to replace the old states.
3) Modified the ALU to always use Operand1 instead of ALU_Ctrl.Data (and removed the field in the record). A new ALU command, ALU_GMSK, was added, as it was the only instruction to set the .Data field to something other than Operand1 (Int_Mask)
4) Modified the package file so that flag names match what the assembler calls them. FL_Z is now PSR_Z, FL_GP1 is now PSR_GP4, etc.
5) Cleaned up the comments and code formatting |
jshamlet |
1607d 05h |
/ |
| 184 |
More file/entity renaming to match private versions. |
jshamlet |
1609d 05h |
/ |
