| Rev |
Log message |
Author |
Age |
Path |
| 79 |
minsoc-install.sh: rpath corrected.
required-cygwin-tools: updated |
rfajardo |
4826d 08h |
/minsoc/ |
| 78 |
minsoc-install.sh: Advanced JTAG bridge compilation needs to know where the dynamic libraries are on runtime. Patching (sed) the Makefile to compile it with the rpath to the libraries (libusb/libftdi). |
rfajardo |
4826d 08h |
/minsoc/ |
| 77 |
New tool requirements for installing Icarus Verilog. |
rfajardo |
4826d 08h |
/minsoc/ |
| 76 |
Including a script allowing the installation of MinSoC and all its required tools.
It should be working for all Linuxes and Cygwin. |
rfajardo |
4826d 08h |
/minsoc/ |
| 75 |
Adapting minsoc_top.v and minsoc_verilog_files.txt to new names for top modules and define file of ethmac ip core. |
rfajardo |
4833d 08h |
/minsoc/ |
| 74 |
or1200.h includes a CLABLE macro which uses __USER_LABEL_PREFIX__(from compiler defined macro) to find out if we need the underscore as prefix to reference C functions (its assembly labels) or not.
except.S and reset.S use CLABLE to call externally defined C functions.
This should avoid problems compiling firmware with old or new toolchain.
support/common.mk updated, reset-nocache.o and reset-icdc.o are dependent on or1200.h |
rfajardo |
4926d 07h |
/minsoc/ |
| 73 |
Makefile does not automatic clean anymore. In Windows rm -f leads to errors and abort synthesis.
minsoc/syn/setup.bat added. Asks for Xilinx settings32|64.bat script and completely implements MinSoC. On completion or error, it holds window open until user input ENTER.
minsoc/sim/modelsim/: *.bat holds window open until user input ENTER.
run_sim.bat asks for target firmware, check if it exists before running simulator. Holds window open and output error message if not found. Does not hold for simulator. |
rfajardo |
4926d 12h |
/minsoc/ |
| 72 |
Adding Windows batch files to run a Modelsim simulation.
-prepare_modelsim.bat, compile_design.bat, run_sim.bat |
rfajardo |
4926d 13h |
/minsoc/ |
| 71 |
Modelsim whines about missing timescales:
-minsoc_bench.v, minsoc_memory_model.v and dbg_comm_vpi.v updated to include timescale.v
modelsim simulation working under Windows. Modelsim PE Student Edition 10.0a
Simulation<->adv_jtag_bridge<->gdb communication not working perfectly. I believe VPI module has to be recompiled, used pre-compiled one for now. |
rfajardo |
4926d 15h |
/minsoc/ |
| 70 |
Including a global timescale under minsoc/rtl/verilog to control simulation. It is under the implementation because the implementation files include it.
Removing timescale definition of minsoc_bench_defines.v files.
Creating a modelsim simulation directory. Everything is working under Linux. For Windows, run_sim.sh has to be changed:
-pli ../../bench/verilog/vpi/jp-io-vpi.so
to:
-pli ../../bench/verilog/vpi/jp-io-vpi.dll
These files have to be compiled/copied from minsoc/rtl/verilog/adv_debug_sys/Software/adv_jtag_bridge/sim_lib/modelsim_platform to minsoc/bench/verilog/vpi. |
rfajardo |
4926d 16h |
/minsoc/ |
| 69 |
backend update:
-minsoc_bench_defines.v
-gcc-opt.mk
Both files should now be under minsoc/backend to proper system functionality.
backend subdirectories have been given those files. Configure script updated accordingly.
They are searched there from system scripts and Makefiles.
-sim/bin/minsoc_verilog_files.txt has the files for Icarus Verilog, minsoc_bench_defines.v is now referenced from backend directory.
-sw/support/Makefile.inc now references to gcc-opt.mk inside backend.
backend/spartan3e_starter_kit_eth:
-It is the system configuration for Spartan 3E Starter Kit with Ethernet. |
rfajardo |
4931d 08h |
/minsoc/ |
| 68 |
Still one configuration mismatch on minsoc_defines.v:
-MEMORY_ADR_WIDTH now 15
-orp.ld is defined accordingly |
rfajardo |
4933d 11h |
/minsoc/ |
| 67 |
Constraint file for backend spartan3a_dsp_kit.ucf was configured to include the STARTUP module.
This module is not enabled under the respective minsoc_defines.v. Thus, its pins had to be commented out. |
rfajardo |
4933d 12h |
/minsoc/ |
| 66 |
spartan3e_starter_kit requires special configuration of or1200_r3.
For that, configure script was specially adapted and that is reported on script execution.
For release-1.0 of MinSoC this should not be required, because or1200_r1 already has the
required configuration. |
rfajardo |
4933d 12h |
/minsoc/ |
| 65 |
Files missing in the last commit.
backend/std/configure
sw: eth, uart and driver Makefiles |
rfajardo |
4933d 13h |
/minsoc/ |
| 64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4933d 15h |
/minsoc/ |
| 63 |
Adding a functional synthesis Makefile system. Still needs a reviews and enhancements, but at least it is something. |
rfajardo |
4937d 08h |
/minsoc/ |
| 62 |
Wrapping different family modules of same manufacturer in a single module.
minsoc_clock_manager.v: uses fpga manufacturer wrappers
xilinx_dcm.v: selects between different Xilinx FPGA families and implements the module
altera_pll.v: selects between different Altera FPGA families and implements the module |
rfajardo |
4937d 15h |
/minsoc/ |
| 61 |
Removing supposely defined external function, which don't exist anymore. |
rfajardo |
4937d 16h |
/minsoc/ |
| 60 |
Selection of memory model or implementation memory is now made on minsoc_bench_defines.v. It is done by a definition instead of including different files for simulation.
minsoc_bench_defines.v definition of reset level was not correct. It based the level decision on defineds POSITIVE_RESET or NEGATIVE_RESET, which couldn't be defined by then, since minsoc_defines.v is not included in minsoc_bench_defines.v. The decision has been moved to minsoc_bench.v and made a localparam instead of a definition. |
rfajardo |
4938d 03h |
/minsoc/ |
