| Rev |
Log message |
Author |
Age |
Path |
| 147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4777d 04h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4804d 21h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 80 |
Establishing a better Makefile system for firmwares. |
rfajardo |
4873d 05h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 65 |
Files missing in the last commit.
backend/std/configure
sw: eth, uart and driver Makefiles |
rfajardo |
4981d 04h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4981d 06h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 55 |
Adjusting Makefiles to compile correctly with new firmware updates.
1) except.o not included into libsupport.a.
2) libsupport.a linked to except.o, now in correct order: ld libsupport.a except.o -o executable (not the other way around)
3) int.c was not being compiled because of a #ifdef which is not set anywhere |
rfajardo |
4994d 02h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 53 |
Indentation, deleting redundant files and adding externals |
ConX. |
4994d 05h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 39 |
FAQ:
-Adv_jtag_bridge self test fails?
-included now SoC flow mistakes
-forgetting to upload the bitfile
-leaving clock unconnected
-older information is now under "Known Issues" right below of SoC flow mistakes
Software:
-eth: included eth.h is from drivers and not from this directory. eth.h from this directory is old and has been removed.
-uart: included uart.h is from drivers and not from this directory. uart.h from this directory is old and has been removed. |
rfajardo |
5100d 18h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 38 |
Small update to HOWTO: advices now to also include the ucf (pinout) file, for forgetful people :-).
FAQ: Added another option (hint) as a solution for people with on-board Xilinx USB cables, which do not reset.
uart.c: now uses the IRQ line definition instead of the line number directly. |
rfajardo |
5135d 17h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 36 |
utils: -adding a 32 to 8 bit Wishbone bridge to connect 8 bit modules to the MinSoC interconnect.
-adding a Linux driver for parallel cables for the adv_jtag_bridge. It circumvents the necessity of privilege to run adv_jtag_bridge with cables xpc3 and xess.
sw/support: support library has been made completely standalone. That means, it is now independent from uClib and/or newlib. Thanks to Wojciech A. Koszek for his contribution on this.
sw/drivers: a driver library has been included, which supply drivers for the OpenRISC timer; and for UART, Ethernet, I2C, and CAN modules from OpenCores.
sw/uart and sw/eth: they don't provide code to control the UART and Ethernet controllers anymore. They use the drivers library instead.
Documentation:
-FAQ extended:
-table of contents
-explanation of how to use the 32 to 8 bit Wishbone bridge
-how to make adv_jtag_bridge work without privilege requirement for xess or xpc3
-explanation of locking problem of xpc_usb cable
-explanation of what to do if the cable is built on-board
-INSTALL:
-patching of gdb only required if version is 6.8, explanation on FAQ now.
-HOWTO:
-instruct to compile drivers library
-remove line numbers information on what to edit, better leave it to be found only by the informed context.
-adv_jtag_bridge execution now without 'sudo'. Note included that 'sudo' is required for Linux and xess or xpc3. Reference to FAQ to avoid this requirement. |
rfajardo |
5166d 23h |
/minsoc/branches/rc-1.0/sw/uart/ |
| 2 |
First commit of project. Beta status:
-testbench: working
-firmware: working
-RTL: Working for: Xilinx Spartan-3A DSP Development Kit |
rfajardo |
5573d 05h |
/minsoc/branches/rc-1.0/sw/uart/ |
