Rev |
Log message |
Author |
Age |
Path |
122 |
Renaming minsoc-configure.sh to minsoc-setup.sh. |
rfajardo |
4685d 08h |
/minsoc/branches/rc-1.0/utils/ |
121 |
Asserting svn:executable properties of modelsim/*.bat scripts.
Including corrected patch for advanced debug system watchpoints under utils/setup. Configure script updated to use this instead of advanced debug system patches. This will remain so until the patch is corrected. The previous line still has the correct command. |
rfajardo |
4685d 09h |
/minsoc/branches/rc-1.0/utils/ |
115 |
configure.sh script dir aware.
minsoc-install.sh logging to script dir. |
rfajardo |
4685d 15h |
/minsoc/branches/rc-1.0/utils/ |
114 |
Installation and Configuration scripts can be run out of any directory.
They assume they are going to process the files and directories found in the directory they are run from. |
rfajardo |
4685d 15h |
/minsoc/branches/rc-1.0/utils/ |
113 |
minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error
spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated
prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files |
rfajardo |
4685d 15h |
/minsoc/branches/rc-1.0/utils/ |
112 |
Updating installation & configuration scripts. |
rfajardo |
4686d 06h |
/minsoc/branches/rc-1.0/utils/ |
111 |
minsoc-install.sh: DIR_TO_INSTALL is required before using beautify.sh |
rfajardo |
4686d 07h |
/minsoc/branches/rc-1.0/utils/ |
110 |
Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure
-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0
-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.
-prj/src: or1200_top.prj downdated to definition of or1200_v1 |
rfajardo |
4686d 07h |
/minsoc/branches/rc-1.0/utils/ |
109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4686d 09h |
/minsoc/branches/rc-1.0/utils/ |
106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4686d 18h |
/minsoc/trunk/utils/ |
103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4696d 10h |
/minsoc/trunk/utils/ |
102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4696d 10h |
/minsoc/trunk/utils/ |
83 |
minsoc-install.sh: bzip2 program was being used, but its existance on target system was not being verified. It is now. |
rfajardo |
4748d 19h |
/minsoc/trunk/utils/ |
82 |
minsoc-install.sh: problems with copying the GNU Toolchain from download to tools. We uncompress the GNU Toolchain now once again to tools during the installation part. |
rfajardo |
4751d 19h |
/minsoc/trunk/utils/ |
81 |
Installation script complete, nice text feedback, output logs and better execution order. |
rfajardo |
4752d 06h |
/minsoc/trunk/utils/ |
79 |
minsoc-install.sh: rpath corrected.
required-cygwin-tools: updated |
rfajardo |
4755d 11h |
/minsoc/trunk/utils/ |
78 |
minsoc-install.sh: Advanced JTAG bridge compilation needs to know where the dynamic libraries are on runtime. Patching (sed) the Makefile to compile it with the rpath to the libraries (libusb/libftdi). |
rfajardo |
4755d 11h |
/minsoc/trunk/utils/ |
77 |
New tool requirements for installing Icarus Verilog. |
rfajardo |
4755d 11h |
/minsoc/trunk/utils/ |
76 |
Including a script allowing the installation of MinSoC and all its required tools.
It should be working for all Linuxes and Cygwin. |
rfajardo |
4755d 11h |
/minsoc/trunk/utils/ |
64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4862d 18h |
/minsoc/trunk/utils/ |