| Rev |
Log message |
Author |
Age |
Path |
| 36 |
utils: -adding a 32 to 8 bit Wishbone bridge to connect 8 bit modules to the MinSoC interconnect.
-adding a Linux driver for parallel cables for the adv_jtag_bridge. It circumvents the necessity of privilege to run adv_jtag_bridge with cables xpc3 and xess.
sw/support: support library has been made completely standalone. That means, it is now independent from uClib and/or newlib. Thanks to Wojciech A. Koszek for his contribution on this.
sw/drivers: a driver library has been included, which supply drivers for the OpenRISC timer; and for UART, Ethernet, I2C, and CAN modules from OpenCores.
sw/uart and sw/eth: they don't provide code to control the UART and Ethernet controllers anymore. They use the drivers library instead.
Documentation:
-FAQ extended:
-table of contents
-explanation of how to use the 32 to 8 bit Wishbone bridge
-how to make adv_jtag_bridge work without privilege requirement for xess or xpc3
-explanation of locking problem of xpc_usb cable
-explanation of what to do if the cable is built on-board
-INSTALL:
-patching of gdb only required if version is 6.8, explanation on FAQ now.
-HOWTO:
-instruct to compile drivers library
-remove line numbers information on what to edit, better leave it to be found only by the informed context.
-adv_jtag_bridge execution now without 'sudo'. Note included that 'sudo' is required for Linux and xess or xpc3. Reference to FAQ to avoid this requirement. |
rfajardo |
5123d 15h |
/minsoc/branches/verilator/ |
| 35 |
minsoc.pdf: -adjusting the date on the page header of MinSoC documentation. It was correct on the front and revision pages, now header adjusted accordingly. |
rfajardo |
5128d 09h |
/minsoc/branches/verilator/ |
| 34 |
start_server changed: '-t' option of adv_jtag_bridge for vpi connection on simulation removed. or1200_v3 will not pass on CPU self test.
FAQ completed with asked questions since Februrary 2010.
INSTALL informs bsdl files only have to be copied to home directory for Xilinx devices.
synthesis_examples title includes Minimal OpenRISC System on Chip. |
rfajardo |
5137d 17h |
/minsoc/branches/verilator/ |
| 33 |
Start-up Starter, included in the MinSoC top file, has been updated to three-phase instruction output; instruction assertion, acknowledge assertion, and next instruction with acknowledge deassertion.
Previously it was two-phase with next instruction, instruction assertion and acknowledge assertion together, and acknowledge deassertion.
That is required by the new Wishbone master interface used by OpenRISC release 3. |
rfajardo |
5145d 19h |
/minsoc/branches/verilator/ |
| 32 |
Documentation revision 1.1, thanks to Wojciech A. Koszek for many comments on it.
Also updating howto, splitint it in INSTALL, HOWTO, FAQ and synthesis_examples, so it should be more clear now what to do when and not to try too much when you don't need. Like everyone was trying to debug the simulation but didn't even test the regular simulation before. Again thanks to Wojciech A. Koszek for his view on this matter. |
rfajardo |
5159d 17h |
/minsoc/branches/verilator/ |
| 31 |
Adaption to or1200_r3. It is still important to change or1200_defines.v:
-`define OR1200_BOOT_ADR 32'hf0000100 to `define OR1200_BOOT_ADR 32'h00000100 |
rfajardo |
5215d 00h |
/minsoc/branches/verilator/ |
| 30 |
minsoc SoC documentation had 2 small typo corrections. Performance penalty due to addition of register addresses was a wrong assumption. On project description "is composed by" -> "consists of". Thanks to Wojciech A. Koszek.
howto, at some places the howto did not tell the path from the files being talked about. I tried to always specify the path for every commented file.
Scripts for running the simulation called bash instead of sh. For compatibility reasons sh is now used, this should affect noone. Scripts do not use bash specific commands and generally every UNIX like computer has sh. Thanks again to Wojciech A. Koszek, who adapted that to port it to FreeBSD. |
rfajardo |
5257d 22h |
/minsoc/branches/verilator/ |
| 29 |
Finishing the howto for Spartan3E Starter Kit with Ethernet. Last hint, change uart baudrate to 9600 to avoid the baudrate skew problem due to truncation.
Following the howto to implement Ethernet on Spartan3E Starter Kit will work flawlessly now. |
rfajardo |
5299d 22h |
/minsoc/branches/verilator/ |
| 28 |
1) Period calculations through 1/freq on testbench use now a numerator definition in order to extract nano seconds of the divisions. Previously the number 1e9 was being repeatedly typed as numerator, now FREQ_NUM_FOR_NS is used.
2) There is a possibility of enabling the GENERIC_CLOCK_DIVISION for the testbench, so that you can test the outcome of different system clock inputs and internal clock adjustments. To do so, NO_CLOCK_DIVISION definition of minsoc_bench_defines.v has to be commented out.
-This also requested the initialization of the internal registers clk_int and clock_divisor of the minsoc_clock_manager.v, this is made by the testbench in case the NO_CLOCK_DIVISION definition is NOT defined.
3) Howto part of implementing Ethernet for the Spartan3E Starter Kit has been completely described. (Chapter 7, subitem 3) |
rfajardo |
5300d 17h |
/minsoc/branches/verilator/ |
| 27 |
Simulation library fpga_memory_primitives.v had an issue with its lpm_ram_dq module, which did not output its data.
The data was being output to doq instead of q, the declared output. doq was also not defined anywhere else.
Icarus Verilog did not detect this, because Verilog-2001 allows internal wires to be used without being defined. To detect this errors, one can define "`default_nettype none". After doing this, Icarus Verilog detected that error and nothing else.
doq changed to q, error corrected. |
rfajardo |
5315d 18h |
/minsoc/branches/verilator/ |
| 26 |
On version 34 of the Advanced Debug System the signal debug_tdo_o from the altera_virtual_jtag has changed to debug_tdo_i.
This commit adapts minsoc_top.v accordingly. |
rfajardo |
5325d 06h |
/minsoc/branches/verilator/ |
| 25 |
Updated the howto document to adapt minsoc to a new update of the Advanced Debug System.
-Compilation of adv_jtag_bridge needs a Makefile adjustment.
-Simulation and Implementation have to remove a definition on the adbg_defines.v file.
Both adjustments simply removes the new JSP (JTAG Serial Port), which has been included in the new release of the Advanced Debug System. |
rfajardo |
5329d 22h |
/minsoc/branches/verilator/ |
| 24 |
E-mail in the documentation has been corrected. |
rfajardo |
5393d 11h |
/minsoc/branches/verilator/ |
| 23 |
Paragraph minor changes, used in announcement and double checked. |
rfajardo |
5397d 15h |
/minsoc/branches/verilator/ |
| 22 |
Status progress and howto pdf documents were not commited, there now. |
rfajardo |
5397d 16h |
/minsoc/branches/verilator/ |
| 21 |
Including the first draft project documentation. How to and status progress docs are now separate from documentation. |
rfajardo |
5397d 18h |
/minsoc/branches/verilator/ |
| 20 |
minsoc_defines.v had a semicolon at the end of the two reset polarity definitions.
minsoc_top had a signal array for two different signals which was for backward compatibility. The compatible debugging module is so old that there is no reason for keeping it.
Documentation has been updated to better explain how to use the definitions files, minsoc_defines.v and or1200_defines.v. An example for Altera devices has been added too. |
rfajardo |
5404d 18h |
/minsoc/branches/verilator/ |
| 19 |
Documentation update. How To: 7) Examples:
-Spartan 3E Starter Kit no Ethernet has been already tested and is known to work.
-Spartan 3E Starter Kit with Ethernet not yet.
-change of sw/support/orp.ld cannot be done by only commenting and uncommenting line, the instruction, documentation line, which said so has been removed.
-Further possibilities -> Further area optimization possibilities. |
rfajardo |
5435d 22h |
/minsoc/branches/verilator/ |
| 18 |
Deprecated comments removed from the file listing files. |
rfajardo |
5467d 22h |
/minsoc/branches/verilator/ |
| 17 |
Ethernet testbench speed penalty solved. Now Ethernet of testbench and minsoc can be enabled by only uncommenting `define ETHERNET on minsoc_defines.v.
send_mac, get_mac and uart_send tasks have been included/improved. Also a testbench, which works for both included firmwares is added. (eth and uart)
If ETHERNET is defined for the SoC, both firmwares will complete successfully. If not, the eth firmware will stall when trying to access the Ethernet module. |
rfajardo |
5469d 17h |
/minsoc/branches/verilator/ |
