| Rev |
Log message |
Author |
Age |
Path |
| 105 |
Updating configure scripts to copy Windows synthesis launch script setup.bat from either minsoc/syn/altera or minsoc/syn/xilinx to minsoc/syn. |
rfajardo |
4772d 23h |
/minsoc/trunk/backend/ |
| 99 |
backend/altera_3c25_board/minsoc_defines.v: if GENERIC_FPGA selected, undefine ALTERA_FPGA and FPGA_FAMILY to avoid vendor specific code to flow into the simulation. If you don't do it, generate_bench fails. |
rfajardo |
4816d 22h |
/minsoc/trunk/backend/ |
| 97 |
As proposed by Javier Almansa automatically generated project files for simulation and synthesis are out of revision control. Instead, the backend configure scripts run the prj/Makefile now to generate the project files prior to configuration of SoC for a specific board. |
rfajardo |
4816d 23h |
/minsoc/trunk/backend/ |
| 96 |
Some files needed for Altera synthesis |
javieralso |
4817d 10h |
/minsoc/trunk/backend/ |
| 95 |
Makefile for Altera FPGAs fixed |
javieralso |
4818d 13h |
/minsoc/trunk/backend/ |
| 93 |
Support for Altera synthesis. It needs some tune, but it works fine |
javieralso |
4821d 00h |
/minsoc/trunk/backend/ |
| 92 |
backend/spartan3e_starter_kit*: or1200_defines.v file was outdated and hindering synthesis. Probably it would be best if we used a patching system here. But for now, I copied the new files and made the necessary changes to fit the system into the target boards. |
rfajardo |
4821d 22h |
/minsoc/trunk/backend/ |
| 88 |
Project structure, Xilinx Makefiles and simulation working. |
rfajardo |
4822d 15h |
/minsoc/trunk/backend/ |
| 87 |
Synchronizing scripts to behave exactly the same. |
rfajardo |
4822d 16h |
/minsoc/trunk/backend/ |
| 86 |
Updating configure script messages. |
rfajardo |
4822d 16h |
/minsoc/trunk/backend/ |
| 85 |
Central project definition under prj. Synthesis and simulation take their project files from here. |
rfajardo |
4822d 16h |
/minsoc/trunk/backend/ |
| 80 |
Establishing a better Makefile system for firmwares. |
rfajardo |
4840d 21h |
/minsoc/trunk/backend/ |
| 70 |
Including a global timescale under minsoc/rtl/verilog to control simulation. It is under the implementation because the implementation files include it.
Removing timescale definition of minsoc_bench_defines.v files.
Creating a modelsim simulation directory. Everything is working under Linux. For Windows, run_sim.sh has to be changed:
-pli ../../bench/verilog/vpi/jp-io-vpi.so
to:
-pli ../../bench/verilog/vpi/jp-io-vpi.dll
These files have to be compiled/copied from minsoc/rtl/verilog/adv_debug_sys/Software/adv_jtag_bridge/sim_lib/modelsim_platform to minsoc/bench/verilog/vpi. |
rfajardo |
4941d 22h |
/minsoc/trunk/backend/ |
| 69 |
backend update:
-minsoc_bench_defines.v
-gcc-opt.mk
Both files should now be under minsoc/backend to proper system functionality.
backend subdirectories have been given those files. Configure script updated accordingly.
They are searched there from system scripts and Makefiles.
-sim/bin/minsoc_verilog_files.txt has the files for Icarus Verilog, minsoc_bench_defines.v is now referenced from backend directory.
-sw/support/Makefile.inc now references to gcc-opt.mk inside backend.
backend/spartan3e_starter_kit_eth:
-It is the system configuration for Spartan 3E Starter Kit with Ethernet. |
rfajardo |
4946d 14h |
/minsoc/trunk/backend/ |
| 68 |
Still one configuration mismatch on minsoc_defines.v:
-MEMORY_ADR_WIDTH now 15
-orp.ld is defined accordingly |
rfajardo |
4948d 17h |
/minsoc/trunk/backend/ |
| 67 |
Constraint file for backend spartan3a_dsp_kit.ucf was configured to include the STARTUP module.
This module is not enabled under the respective minsoc_defines.v. Thus, its pins had to be commented out. |
rfajardo |
4948d 18h |
/minsoc/trunk/backend/ |
| 66 |
spartan3e_starter_kit requires special configuration of or1200_r3.
For that, configure script was specially adapted and that is reported on script execution.
For release-1.0 of MinSoC this should not be required, because or1200_r1 already has the
required configuration. |
rfajardo |
4948d 18h |
/minsoc/trunk/backend/ |
| 65 |
Files missing in the last commit.
backend/std/configure
sw: eth, uart and driver Makefiles |
rfajardo |
4948d 19h |
/minsoc/trunk/backend/ |
| 64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4948d 21h |
/minsoc/trunk/backend/ |
| 63 |
Adding a functional synthesis Makefile system. Still needs a reviews and enhancements, but at least it is something. |
rfajardo |
4952d 14h |
/minsoc/trunk/backend/ |
