| Rev |
Log message |
Author |
Age |
Path |
| 113 |
Read with single block works on cards, but not in simulation. SdData.sv
sends data with one "XXXX" cycle right before the crc. |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 112 |
Save wide mode with out gHighSpeedMode = true |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 111 |
Sclk moved to neg. edge -> setup and hold times for fast mode are easier
to reach. (only micro sd does not work in fast mode). |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 110 |
All except microsd work in highspeed mode. |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 109 |
Added a data ram. |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 108 |
Added a ram to the testbed |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 106 |
Fixes #29: All cards respond, but they do not all work. |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 105 |
Changing speed works! refs #33 |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 104 |
SdController: Configuration ready to switch to high speed, refs #33 |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 103 |
SdController: Checking speed works |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 102 |
SdController: Enabling wide mode works, refs #33 |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 101 |
Receiving response to ACMD51 works including data, refs #33. |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 100 |
SdController: Receiving data after ACMD51, but CRC is wrong |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 99 |
SdController: Checking bus width without receiving data response |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 98 |
SdController: Receive response to CMD7 (except when busy is activated) |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 97 |
SdController: CMD55 out of main state into Region |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 96 |
SdController: Region extracted from main state, select card in config
state |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 95 |
SdController: entity and architecture split, all outputs registered
SdCardModel: Delay between response and next command added
SdData: Busy checking
refs #33 |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 94 |
CmdTimeout (8 Clocks) added, SdData inserted into top, refs #31 |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
| 90 |
Fixes the milestone ReadCID. It works with SD2.0 (non HC) card. |
rkastl |
4928d 20h |
/sdhc-sc-core/trunk/src/grpSd/unitSdController/src/ |
