| Rev |
Log message |
Author |
Age |
Path |
| 110 |
Fixed a problem whereby block RAM would be declared as a bus error on the
stack, even if the data was valid. |
dgisselq |
2876d 10h |
/xulalx25soc/ |
| 109 |
This continues the updates to the wishbone-uart conversion. It fixes several
bugs within wbuexec, and pipelines the compression scheme. Further, the
read codeword was adjusted so that a read of 8 can be requested with six-bits,
rather than requiring 12. Likewise, the dependence upon the read of 8 on
incrementing the address pointer has been removed. All told, the design
builds for a 200MHz Artix-7, and it has been tested with the CMod-S6. (Writing
flash seems to be one of the most comprehensive tests ...) |
dgisselq |
2876d 14h |
/xulalx25soc/ |
| 108 |
Minor documentation updates. |
dgisselq |
2877d 00h |
/xulalx25soc/ |
| 107 |
Minor change. |
dgisselq |
2877d 00h |
/xulalx25soc/ |
| 106 |
Minor, inconsequential changes. |
dgisselq |
2877d 00h |
/xulalx25soc/ |
| 105 |
Mostly cosmetic changes. The Makefile now builds a couple more programs,
the documentation is better, etc. |
dgisselq |
2877d 00h |
/xulalx25soc/ |
| 104 |
Updates to the flash driver drawn from the S6SoC project. |
dgisselq |
2877d 00h |
/xulalx25soc/ |
| 103 |
Added a SDSPI scope, and defined which of the four scopes it points to.
(It uses the configuration scopes position, if the configuration scope isn't
defined.) |
dgisselq |
2877d 00h |
/xulalx25soc/ |
| 102 |
Updated documentation. The documentation for these now also reflects that
these were drawn from an FPGA Library project, that is shared among many
FPGA builds. |
dgisselq |
2877d 00h |
/xulalx25soc/ |
| 101 |
Fixed the `defines at the top so that this can be built without any CPU.
This was then used to measure the impact of the CPU on the entire build, as
you could now build with no CPU, and then with a CPU to compare. |
dgisselq |
2877d 01h |
/xulalx25soc/ |
| 100 |
Includes updates so this can run at higher clocks speeds within an FPGA. |
dgisselq |
2877d 01h |
/xulalx25soc/ |
| 99 |
Includes high-speed updates. rxuart and txuart will now run at 200MHz on
an Artix-7, so should not impact timing (any more) on the XuLA platform. |
dgisselq |
2877d 01h |
/xulalx25soc/ |
| 98 |
Updated copyright notices for the new year, to reflect that changes have been
made in 2016. |
dgisselq |
2877d 01h |
/xulalx25soc/ |
| 97 |
Latest working bit file, with all changes attached as of this date. |
dgisselq |
2900d 05h |
/xulalx25soc/ |
| 96 |
Now accepts an SD-Card backing file, so that SD-Card reads *and* writes can be
tested. |
dgisselq |
2900d 05h |
/xulalx25soc/ |
| 95 |
Added write capability to the SD-SPI simulator. |
dgisselq |
2900d 05h |
/xulalx25soc/ |
| 94 |
Fixes a bug which had caused the device to die artificially and early, just
simply because the program connecting to the simulator shut its pipe down before
getting our last message. We now ignore this signal and continue. |
dgisselq |
2900d 05h |
/xulalx25soc/ |
| 93 |
Oops -- missed adjusting the copyright. |
dgisselq |
2900d 05h |
/xulalx25soc/ |
| 92 |
Fixes the problem whereby the master counters show when the user counters should
be showing and vice versa. Now the master counters show by default, together
with their correct labels. User counters are still available by pressing
'u' in the debugger, and the master counter display may be returned to by
pressing 'm' in the debugger. |
dgisselq |
2900d 05h |
/xulalx25soc/ |
| 91 |
Fixes bugs associated with an overflow of write acknowledgements in the
receiver. This helps keep our accesses aligned. |
dgisselq |
2900d 05h |
/xulalx25soc/ |
